Craftsman 917.27242 owner manual Engine

Page 27

REPLACINGBATTERY

TO REMOVE HOOD AND GRILL AS- SEMBLY

_IkCAUT!ON: Do not short battery terminais Dy allowing a wrench or any

other object to contact both terminals at the same time, Before connecting battery, remove metal bracelets, wristwatch

bands, rings, etc.

Positive terminal must be connected first

to prevent sparking from accidental grounding.

1.Lift seat pan to raised position and open battery box door.

2.Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

3.Install new battery with terminals in

same position as old battery.

4, First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely.

5.Connect BLACK grounding cable to negative (-) terminal with remaining hex bolt and keps nut, Tighten securely.

6.Close battery box door.

Seat PanI

Battery _.,,-"_!_,

Ooor_ F_II_

Box__

Keps

Hex Belt

Positive(Red) Cable Negative (Black) Cable

TO REPLACE HEADLIGHT BULB

1.Raise hood.

2.Pull bulb holder out of the hole in the backside of the grill.

3.Replace bulb in holder and push bulb holder securely back into the hole in

the backside of the grill. 4, Close hood,

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check widng. See electrical wiring

diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-typeplug-in fuse, The fuse holder is located behind the dash.

1, Raise hood.

2, Unsnap headlight wire connecter.

3, Stand in front of tractor. Grasp hood at

sides, tilt toward engine and lift off of tractor.

4. To replace, reverse above procedure.

,, _ Hood

i_ Headlight Wire

._) Connector

ENGINE

Maintenance, repair,or replacement of the emission control devicas and systems, which

are being done at the customers expense,

may be performed by any non-road engine repairestablishmentor individual. Warranty

repairs must be performed by an authorized engine manufacture¢s service outlet.

TO ADJUST THROTTLE CONTROL

CABLE

The throttlecontrol has been preset at the factory and adjustment should not be necessary.Check adjustment as described

below before loosening cable. If adjustment is necessary, proceed as follows:

1.With engine not running, move throttle control lever from slow to choke position. Slowlymove lever from choke to fast position.

2.Check to see if hole in throttlelever and hole in speed control bracket are aligned.

3.If holes are not aligned, loosen cable clamp screw and align the holes by

insertinga pencil or a 1/4" drillbit through beth holes.

4, Pull throttlecable up to remove slack and tightencable clamp screw, Remove alignment pencil or drillbit.

Cable _

Clamp _.__.__L:_['_

Screw _----]

Speed Coontrol _'_/_ I

_Bracket

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Questions Lawn TractorLimited 90 DAY Warranty on Battery MaintenanceII. Slope Operation Clean any oil or fuelGeneral Operation StorageThat may obscure vision IV. ServiceIII. Children You last saw themPage Forward Product SpecificationsGallons UnleadedSlope Sheet Tools Required for Assembly HOW to SET UP Your Tractor Check BatteryCarton Unpack Carton Sure the area in front of tractor is clear Battery DoorInstall Seat LabelInstall Mulcher Plate RlR N H L Freewheel Control Knowyour TractorThrottle/Choke Control LiftLeverEngine HOW to USE Your Tractor To SET Parking BrakeTo Adjust Mower Cutting Height StoppingTo Transport To Adjust Gauge WheelsTo Operate Mower To Operate on HillsADD Gasoline Towing Carts and Other ATTACH- MentsBefore Starting the Engine Check Engine OIL Level Engine in your tractor has beenPurge Transmission Automatic Transmission Warm UPMulching Mowing Tips Mowing TipsOnce a year you should replace Lubrication ChartMaintenance Schedule General RecommendationsBlade Removal TiresOperator Presence System Blade CareTranbaxle Cooling Transaxle Pump Fluid BatteryTo Clean Battery and Terminals BeltsAIR Filter Clean AIR ScreenClean AIR INTAKE/COOLING Areas To Service PRE-CLEANERCleaning IN-LINE Fuel FilterFuel Filter Retainer Spring To Install MowerTo Remove Mower Move attachment lift lever forward toBelt Removal SIDE-TO-SIDE AdjustmentMower to To Replace Mower Blade Drive BeltTo Replace Motion Drive Belt Belt InstallationTo Adjust Brake Transaxle Motion Control Lever Neutral AdjustmentFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery Transmission REMOVAL/REPLACE- MentEngine To Adjust Carburetor AdjustingAcceleration Test Other Engine Fuel SystemEngineoil CylindersCorrection Troubleshooting ChartProblem CauseVibration Loss of powerFuel ExcessiveOFF Troubleshooting Chart ProblemcauseTractor - Model Number SchematicElectrical Tractor --MODEL NumberKEY Part Description Tractor -- Model NumberTractor - Model Number 917.272420 Chassis and Enclosures KEY Part Description TRACTOR--MODEL Number Chassis and EnclosuresTRACTOR--MODEL Number Ground Drive Inches 1 inch= 25.4 mm TRACTOR--MODELNUMBER917.272420 Steeringassembly TRACTOR- -MODELNUMBER917.272420 Steeringassembly Optional Equipment r Spark Arrester KEY Part NO. NO.DESCRIPTION TRACTOR-- ModelnumberTRACTOR--MODEL Number Seat Assembly Wheels & Tires DecalsTractor - Model Number Liftassembly Washer 21/32 x 1 x21 Gauge 120183X Beadng, Nylon TRACTOR- Model Number Lift AssemblyTractor --MODEL Number Mower Deck O3J72140614 Ill Assembly 170408 Crankcase I CARTER-MOTEUR KEY Part Oescription Arede ARRIVSEJ1 AIR INTAKE/FILTRATION Engine Controls OIL PAN/LUBRICATION UEL DE LE Systemei Crankshaft KEY Part Service Notes Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation Part 80o-366-7278888-SU.HOGARsM

917.27242 specifications

The Craftsman 917.27242 is a high-performance riding lawn mower that delivers the power and precision needed for effective lawn maintenance. Designed for efficiency and ease of use, this model is ideal for homeowners with medium to large-sized lawns.

One of the standout features of the Craftsman 917.27242 is its robust 24 HP Kohler engine. This powerful engine ensures reliable starting and strong performance, making mowing tasks quicker and more efficient. Coupled with a hydrostatic transmission, the mower offers seamless speed adjustments without the need for shifting gears, allowing users to maneuver easily across various terrains.

The mower is equipped with a 42-inch cutting deck, which strikes a balance between size and maneuverability. This deck size is suitable for efficiently tackling both small and large areas while still being able to navigate tighter spaces like flower beds or around trees. The cutting height can be easily adjusted from 1.5 to 4 inches, enabling customization based on grass type and seasonal requirements.

In terms of technology, the Craftsman 917.27242 features an innovative, ergonomic design that enhances user comfort. The seat is adjustable, ensuring a relaxed riding position for operators of different heights. Additionally, the intuitive control panel simplifies operation, incorporating easily accessible controls for starting, cutting height adjustments, and more.

Safety is a priority in the Craftsman design. The mower includes features such as a blade brake that automatically engages when the operator leaves the seat, ensuring that the blades stop immediately when needed. This prevents accidents and adds a layer of security, especially when users need to dismount.

Moreover, the Craftsman 917.27242 is compatible with various attachments, making it a versatile choice. Beyond just mowing, attachments like baggers, mulch kits, and even snow plows can transform this machine for year-round use.

Overall, the Craftsman 917.27242 combines power, efficiency, and user-friendly features to provide an exceptional mowing experience. Suitable for both residential and light commercial use, it stands out in a competitive market, delivering reliability and high-quality performance that homeowners can depend on for maintaining their lawns.
Top Page Image Contents