Craftsman 917.27339 owner manual Mulching Mowing Tips

Page 16

MOWING TIPS

Mower should be properly leveled for best mowing performance. See "TO LEVEL MOWER HOUSING" in the

Service and Adjustments section of this manual.

The left hand side of mower should be used for trimming.

Drive so that clippings are discharged onto the area that has already been

cut. Have the cut area to the right of the tractor. This will result in a more

even distribution of clippings and more uniform cutting.

When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds,

mow in the opposite direction making left hand turns until finished.

(-

1

(- . : jj

00272

If grass is extremely tall, it should be mowed twice to reduce load and pos- sible fire hazard from dried clippings.

Make first cut relatively high; the second to the desired height.

Do not mow grass when it is wet. Wet grass wilt plug mower and leave undesirable clumps. Allow grass to dry before mowing.

Always operate engine at full throttle when mowing to assure better mowing performance and proper discharge of material. Regulate ground speed by selecting a low enough gear to give the mower cutting performance as well as the quality of cut desired.

When operating attachments, select a ground speed that wilt suit the terrain and give best performance of the at- tachment being used.

MULCHING MOWING TIPS

IMPORTANT: For best performance, keep mower housing free of built-up grass and trash. Clean after each use.

The special mulching blade will recut the grass clippings many times and reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed. Also, the mulched grass will biodegrade quickly to provide nutrients for the lawn. Always mulch with your highest engine (blade) speed as this wilt provide the best recut- ting action of the blades.

Avoid cutting your lawn when it is wet. Wet grass tends to form clumps and interferes with the mulching action. The best time to mow your lawn is the early afternoon. At this time the grass has dried, the newly cut area will not be exposed to direct sunlight.

For best results, adjust the mower cutting height so that the mower cuts off only the top one-third of the grass blades. For extremely heavy grass, re- duce your width of cut on each pass and mow slowly.

MAX 1/3

Certain types of grass and grass conditions may require that an area be mulched a second time to completely hide the clippings. When doing a sec- ond cut, mow across (perpendicular) to the first cut path.

Change your cutting pattern from week to week. Mow north to south one week

then change to east to west the next week. This wilt help prevent matting and graining of the lawn.

16

Image 16
Contents Jcriiftsmiinj Limited Warranty on Craftsman Riding Equipment Limited Warranty on BatteryII. Slope Operation General OperationIII. Children IV. ServiceDo not Page Product Specifications Repair Protection AgreementsSeat Steering WheelKeys Slope Sheet Video Cassette Tools Required for Assembly Assemble Extension Shaft and BootTo Remove Tractor from Unpack CartonCheck Battery Install Mulcher Plate Check Brake SystemDischarging Check Tire Pressure@@@@@ Ammeter Know Your TractorLift Lever HOW to USE Your Tractor To SET Parking Brake Throttle reduces the battery charging rateTo USE Throttle Control Always operate engine at full throttleTo Operate On Hills Do not drive up or downTo Transport Towing Carts and Other Attach MentsTo Start Engine ADD GasolineMowing Tips Mulching Mowing TipsGeneral Recommendations Lubrication ChartBefore Each USE Operator Presence System TractorBlade Removal Battery EngineTransaxle Cooling BeltsClean AIR Screen AIR FilterEngine Cooling System Spark PlugsTo Install Mower CleaningTractor To Remove Mower To Level Mower Housing SIDE-TO-SIDE AdjustmentBelt Installation To Check and Adjust BrakeTo Check Brake Belt RemovalTo Adjust Steering Wheel Align Ment Transaxle Gear Shift Lever NEU Tral AdjustmentFront Wheel TOE-IN/CAMBER To Start Engine with a Weak BAT TeryReplacing Battery Interlocks and RelaysTo Replace Fuse To Remove Hood and Grill AS- SemblyTo Adjust Throttle Control Cable Preliminary SettingFinal Setting To Adjust CarburetorBattery Engine OILCylinders OtherProblem Troubleshooting ChartEngine will not turn over Engine clicks but will not start Problem Loss of powerExcessive VibrationBattery will Not Mower blades willNot rotate Poor grassTractor - Model Number Schematic BlackTractor - Model Number Electrical KEY Part NO. NO. Description 20f Tractor - Model Number 917.273390 Chassis and EnclosuresKEY Part Description 7oo Tractor - Model Number Ground DriveKEY Part Tractor - Model Number 917.273390 Steering Assembly KEY Part Description Engine Tractor - Model NumberOptional Equipment Tractor - Model Number Seat Assembly KEY Part Tractor - Model Number DecalsWheels &TIRES KEY Part Description Tractor - Model Number Lift Assembly Tractor - Model Number Mower Deck KEY Part NO. NO.DESCRIPTION 15729B Part Description 20@ 7Sv5 108A 917.273390 Tractor Model NumberBriggs ENGINE-MODEL Number KEY Part NO. NO.DESCRIPTION Description Page Page Suggested Guide for Sighting Slopes for Safe Operation AR 0 4,0

917.27339 specifications

The Craftsman 917.27339 is a versatile riding lawn mower designed for homeowners seeking efficiency and performance in lawn maintenance. This model boasts a robust build quality, making it a popular choice among gardening enthusiasts and professional landscapers alike.

One of the standout features of the Craftsman 917.27339 is its powerful 26-horsepower Kohler engine, providing ample power for tackling a variety of lawn sizes and terrains. The engine ensures reliable performance and longevity, making it suitable for both residential use and larger landscapes. The mower is equipped with a hydrostatic transmission, which allows for smooth speed transitions without the need for shifting gears, making it easy to maneuver around obstacles and varying terrains.

The cutting deck is another highlight of the Craftsman 917.27339. With a 54-inch cutting width, it is designed to efficiently handle large mowing areas, reducing the time required to complete lawn care tasks. The deck features a 12-gauge steel construction, which increases durability and allows for effective grass cutting and collection. The adjustable cutting height, ranging from 1.5 to 4 inches, provides users with flexibility, enabling them to achieve the desired lawn finish.

In terms of technology and user convenience, the Craftsman 917.27339 is equipped with an ergonomic seat and steering wheel, promoting comfort during extended use. The mower also features an easy-to-access control panel that provides essential information at a glance, including speed and fuel levels.

For those concerned about grass clippings, this model includes a rear discharge option, which helps to distribute clippings evenly across the lawn, promoting healthier grass growth. Additionally, the optional bag attachment allows for easy collection of clippings, keeping your yard neat and tidy.

The Craftsman 917.27339 stands out not only for its performance but also for its ease of maintenance. It features quick-change oil and air filters, allowing users to perform routine upkeep without hassle. With its combination of power, comfort, and cutting-edge features, the Craftsman 917.27339 is an ideal choice for anyone looking to maintain a beautiful, well-manicured lawn with minimal effort.