Craftsman 917.27339 owner manual Front Wheel TOE-IN/CAMBER, To Start Engine with a Weak BAT Tery

Page 24

5.Make sure belt is in all pulley grooves and inside all belt guides and keepers.

6.Install mower (See "TO INSTALL MOWER" in this section of manual).

Enc

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not

adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or

camber, contact a Sears or other qualified service center.

TO REMOVE WHEEL FOR REPAIRS

 

Center

Clutchin4

.Span

 

Keeper

Stationary Idler

Transaxte

TRANSAXLE GEAR SHIFT LEVER NEU-

TRAL ADJUSTMENT

The transaxle should be in neutral when

the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

1.Make sure transaxte is in neutral (N). NOTE: When the tractor rear wheels move

freely, the transaxle is in neutral.

2.Loosen ad ustment bolt in front of the right rear wheel.

3.Position the gear shift lever in the neu- tral (N) position.

4.Tighten adjustment bolt securely. NOTE: If additional clearance is needed

to get to adjustment bolt, move mower

1.Block up axle securely.

2.Remove axle cover, retaining ring and washers to allow wheel removal (rear wheels have a square key - Do not lose).

3.Repair tire and reassemble.

NOTE: On rear wheels only: align

grooves in rear wheel hub and axle. Insert square key.

4.Replace washers and snap retaining ring securely in axle groove.

5.Replace axle cover.

NOTE: To seal tire punctures and prevent

flat tires due to slow leaks, purchase and use tire sealant from Sears. Tire sealant

also prevents tire dry rot and corrosion.

Washers

Retaining

Ring

Axle

Cover

I

Square Key

(Rear Wheel Only)

TO START ENGINE WITH A WEAK BAT-

TERY

deck height to the lowest position.

Neutral Lock Gate

Gearshift

 

f

 

 

......

/"

,t

Adjustment Bolt

...... ....,

i

TO ADJUST STEERING WHEEL ALIGN-

MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble with crossbars horizontal. Tighten securely.

,_WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from bat-

teries. Always wear eye protection when around batteries.

If your battery is too weak to start the

engine, it should be recharged. (See "BAT- TERY" in the MAINTENANCE section of

this manual).

If "jumper cables" are used for emergency starting, follow this procedure: IMPORTANT: Your tractor is equipped with a 12 volt system. The other vehicle must also be a 12 volt system. Do not use your tractor battery to start other vehicles.

TO ATTACH JUMPER CABLES -

1. Connect one end of the RED cable to the POSITIVE (+) terminal of each battery(A-B), taking care not to short

24

against tractor chassis.

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Jcriiftsmiinj Limited Warranty on Craftsman Riding Equipment Limited Warranty on BatteryII. Slope Operation General OperationIV. Service III. ChildrenDo not Page Product Specifications Repair Protection AgreementsSteering Wheel SeatKeys Slope Sheet Video Cassette Tools Required for Assembly Assemble Extension Shaft and BootTo Remove Tractor from Unpack CartonCheck Battery Install Mulcher Plate Check Brake SystemDischarging Check Tire Pressure@@@@@ Know Your Tractor AmmeterLift Lever HOW to USE Your Tractor To SET Parking Brake Throttle reduces the battery charging rateTo USE Throttle Control Always operate engine at full throttleTo Operate On Hills Do not drive up or downTo Transport Towing Carts and Other Attach MentsTo Start Engine ADD GasolineMowing Tips Mulching Mowing TipsLubrication Chart General RecommendationsBefore Each USE Tractor Operator Presence SystemBlade Removal Battery EngineTransaxle Cooling BeltsClean AIR Screen AIR FilterEngine Cooling System Spark PlugsCleaning To Install MowerTractor To Remove Mower To Level Mower Housing SIDE-TO-SIDE AdjustmentBelt Installation To Check and Adjust BrakeTo Check Brake Belt RemovalTo Adjust Steering Wheel Align Ment Transaxle Gear Shift Lever NEU Tral AdjustmentFront Wheel TOE-IN/CAMBER To Start Engine with a Weak BAT TeryReplacing Battery Interlocks and RelaysTo Replace Fuse To Remove Hood and Grill AS- SemblyTo Adjust Throttle Control Cable Preliminary SettingFinal Setting To Adjust CarburetorBattery Engine OILCylinders OtherTroubleshooting Chart ProblemEngine will not turn over Engine clicks but will not start Problem Loss of powerExcessive VibrationBattery will Not Mower blades willNot rotate Poor grassTractor - Model Number Schematic BlackTractor - Model Number Electrical KEY Part NO. NO. Description 20f Tractor - Model Number 917.273390 Chassis and EnclosuresKEY Part Description 7oo Tractor - Model Number Ground DriveKEY Part Tractor - Model Number 917.273390 Steering Assembly KEY Part Description Tractor - Model Number EngineOptional Equipment Tractor - Model Number Seat Assembly Tractor - Model Number Decals KEY PartWheels &TIRES KEY Part Description Tractor - Model Number Lift Assembly Tractor - Model Number Mower Deck KEY Part NO. NO.DESCRIPTION 15729B Part Description 20@ 7Sv5 108A Tractor Model Number 917.273390Briggs ENGINE-MODEL Number KEY Part NO. NO.DESCRIPTION Description Page Page Suggested Guide for Sighting Slopes for Safe Operation AR 0 4,0

917.27339 specifications

The Craftsman 917.27339 is a versatile riding lawn mower designed for homeowners seeking efficiency and performance in lawn maintenance. This model boasts a robust build quality, making it a popular choice among gardening enthusiasts and professional landscapers alike.

One of the standout features of the Craftsman 917.27339 is its powerful 26-horsepower Kohler engine, providing ample power for tackling a variety of lawn sizes and terrains. The engine ensures reliable performance and longevity, making it suitable for both residential use and larger landscapes. The mower is equipped with a hydrostatic transmission, which allows for smooth speed transitions without the need for shifting gears, making it easy to maneuver around obstacles and varying terrains.

The cutting deck is another highlight of the Craftsman 917.27339. With a 54-inch cutting width, it is designed to efficiently handle large mowing areas, reducing the time required to complete lawn care tasks. The deck features a 12-gauge steel construction, which increases durability and allows for effective grass cutting and collection. The adjustable cutting height, ranging from 1.5 to 4 inches, provides users with flexibility, enabling them to achieve the desired lawn finish.

In terms of technology and user convenience, the Craftsman 917.27339 is equipped with an ergonomic seat and steering wheel, promoting comfort during extended use. The mower also features an easy-to-access control panel that provides essential information at a glance, including speed and fuel levels.

For those concerned about grass clippings, this model includes a rear discharge option, which helps to distribute clippings evenly across the lawn, promoting healthier grass growth. Additionally, the optional bag attachment allows for easy collection of clippings, keeping your yard neat and tidy.

The Craftsman 917.27339 stands out not only for its performance but also for its ease of maintenance. It features quick-change oil and air filters, allowing users to perform routine upkeep without hassle. With its combination of power, comfort, and cutting-edge features, the Craftsman 917.27339 is an ideal choice for anyone looking to maintain a beautiful, well-manicured lawn with minimal effort.
Top Page Image Contents