Craftsman 917.272054 owner manual Tractor

Page 18

TRACTOR

Always observe safety rules when performing any maintenance.

BRAKE OPERATION

If tractorrequires more than six (6) feet stopping distance at high speed in highest gear, then brake must be ad- justed. (See "TO ADJUST BRAKE" in the

Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See "PRODUCT SPECIFICATIONS" section of this manual).

•Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent fiat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and intedock systems are working propedy. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the clutch/brake pedal is fully depressed and attachment clutch control is in the

disengaged position.

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment dutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never

operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be

kept sharp. Replace bent or damaged blades.

BLADE REMOVAL

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

4.Reassemble hex bolt, lock washer and fiat washer in exact order as shown.

5.Tighten bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: Blade bolt is grade 8 heat treated.

Star

Center

Flat Washer

Mandrel

Assembly

_--Hex Bolt,

*A Grade8 heat b'eatedbolt can be identified by six lines on the bolthead.

TO SHARPEN BLADE

NOTE: We do not recommend sharpen- ing blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and eventual

damage to mower and engine.

•The blade can be sharpened with a file or on a gdnding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone bal- ancer, follow the instructionssupplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position, if either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

5/8" Bo_ CenterHole._

or Pin _

_"_'_._

1.Raise mower to highest position to allow access to blades.

2.Remove hex bolt, lock washer and fiat washer securing blade.

3.Install new or resharpened blade with trailing edge up towards deck as shown.

BATTEF Y _ _Blade

Your tractor has a battery charging system whioh is sufficientfor normal use. How-

ever, periodic charging of the battery with an automotive charger will extend its life.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Lawn Tractor For answers to your questionsLimited 90 DAY Warranty on Battery General Operation Mow only in daylight or good artificial lightI1. Slope Operation IV. Service Cancer and birth defects or other repro- ductive harm Productspecifications Ooo Before Removing Tractor from Skid Attachsteeringwheel Install Seat Lower seat into operating position and sit in seatChecktire Pressure Install Mulcher PlateTo Convertto Bagging or Discharging Check Deck LevelnessBattery Reverse Forward Fast Ammeter Indicates charging + or discharging of battery KnowyourtractorStopping To Adjust Mower Cutting HeightHowto Useyourtractor To SET Parking Brake Ground DriveTo Operate on Hills To Adjust Gauge WheelsTo Operate Mower To TransportADD Gasoline Towing Carts and Other AttachmentsBefore Starting the Engine Check Engine OIL Level To Start EngineMulching Mowingtips Lubrication Chart General RecommendationsBefore Each USE Tractor Clean AIR INTAKE/COOLING Areas To Clean Battery and TerminalsClean AIR Screen BeltsEngine OIL Filter To Service CartridgeAIR Filter IN-LINE Fuel FilterTo Remove Mower CleaningTo Install Mower Raise attachment lift lever to its highest positionTo Level Mower Housing SIDE-TO-SIDE AdjustmentPulley To Adjust BrakeTo Replace Mower Blade Drive Belt To Replace Motion Drive BeltTo Adjust Steering Wheel ALIGN- Ment Transaxle Gear Shift Lever Neutral AdjustmentTo Start Engine with a Weak Battery To Remove Wheel for RepairsTo Replace Headlight Bulb Replacing BatteryTo Remove Hood and Grill Assembly Interlocks and RelaysTo Adjust Throttle Control Cable To Adjust CarburetorEngine Fuel System To Clean Battery and TermiTractor Engine OILCause TroubleshootingchartProblem CorrectionTroubleshooting Chart Problem Cause For 30 seconds before Troubleshooting Chart ProblemCause Correction Stopping engineSchematic TCR- Model NumberTRACTOR- -MODEL NUM BER Electrical TRACTOR-- Model Number Electrical NO. NO,DESCRIPTIONTractor - Model Number 917.272054 Chassis and Enclosures TRACTOR- -MODELNUMBER917.272054 Chassisandenclosures KEY Part NO, NO, DescriptionTRACTOR- -MODEL Number Ground Drive TRACTOR- Model Number Ground Drive X .1645/1865Shift Rate TRACTOR--MODEL Number Steering Assembly TRACTOR- Model Number 917.272054 Steeringassembly KEY Part NO. NO.DESCRIPTIONTRACTOR--MODELNUMBER917.272054 Engine KEY Part DescriptionTRACTOR-- MODELNUMBER917.272054 Seatassembly Wheels & Tires DecaJ, V-Belt SchematicTRACTOR- Model Number Decals 99904TRACTOR- Model Number Liftassembly TRACTOR-- Model Number Mowerdeck TRACTORMODELNUMBER917--.272054 Mowerdeck STD693107Page Ring TRACTOR--MODELNUMBER917.272054PEERLESSTRANSAXLE- Model NUMBER206-545C Oil Seal 9 1Cylinder HEAD, Valve and Breaiieri Crankcasi Gasket 25-186-01-S14-0 Blower Housing Baffles KEY Part Descripon 25-086-47.SStarting System Engine Controls OIL PAN / Lubrication KEY Part NO. NO.DESCRIPTION Crankshaft Available ExhausPage Page Page Suggested Guide for Sighting Slopes for Safe Operation 3s6-7278 Sears,com/patsdirect 178457 2.20,01 RD

917.272054 specifications

The Craftsman 917.272054 is a robust and efficient riding lawn mower designed to make lawn maintenance a breeze. This machine features a powerful 24 HP Kohler engine, delivering reliable performance and significant torque, enabling it to tackle even the toughest grass and terrain with ease. One of the standout characteristics of the 917.272054 is its hydrostatic transmission, which offers smooth and variable speed control. This allows the operator to maneuver easily without the need for gear shifting, providing a more comfortable mowing experience.

Equipped with a 54-inch cutting deck, the Craftsman 917.272054 allows for a wide cutting path, significantly reducing mowing time, especially for larger lawns. The cutting deck features multiple height adjustments, ranging from 1.5 to 4 inches, allowing users to achieve the perfect cut tailored to the specific needs of their grass type. This adaptability promotes healthy grass growth and enhances the overall appearance of the lawn.

The mower also showcases a rugged and durable construction, making it suitable for various conditions. The front axle is designed for added stability, while the reinforced deck is engineered to withstand the rigors of frequent use. Another notable feature is the comfortable high-back seat that provides excellent lumbar support, essential for long mowing sessions.

For enhanced convenience, the Craftsman 917.272054 includes an easy-to-use dashboard with essential controls conveniently located for quick adjustments while operating. The ignition switch is designed for easy starting, and the mower includes a sturdy grass collection system for effortless cleaning and maintenance.

Additionally, this lawn mower is compatible with various attachments, including baggers, mulch kits, and other accessories, allowing users to customize their mowing experience based on their lawn care needs. Safety features like the operator presence control ensure that the mower will shut off if the operator leaves the seat, adding an extra layer of protection.

Overall, the Craftsman 917.272054 stands out as an exemplary choice for homeowners seeking a reliable and efficient lawn mower that combines power, functionality, and user-friendly design. With its advanced features and technologies, it makes lawn maintenance not only easier but also more enjoyable.
Top Page Image Contents