Craftsman 917.272054 owner manual Before Removing Tractor from Skid Attachsteeringwheel

Page 8

Yournew tractor has been assembed at the factory with exception of those parts lel unassembled for shipping purposes, To ensure safe and proper operation of your tractor all parts and hardware you assemble must he tightened securely. Use the correct tools as necessary to insure proper tightness. Review the video cassette be you begin,

TOOLS REQUIRED FOR

ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes you need are listed below.

(1)

9/16"wrench

(1)

Pliers

(2)

1/2"wrench

(1)

Utility knife

(1)

Tire pressure gauge

 

When right or left hand is mentioned in this manual, it means, from your point of

view, when you are in the operating position (seated behind the steedng

wheel),

TO REMOVETRACTOR FROM CARTON

UNPACK CARTON

1.Remove all accessible loose parts and parts cartons from carton.

2.Cut. from top to bottom, along lines on all four corners of carton, and lay panels flat.

3.Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID ATTACHSTEERINGWHEEL

ASSEMBLE EXTENSION SHAFT AND

BOOT

1.Slide extension shaft onto lower

steering shaft. Align mounting holes in extension and lower shafts and install 5/16 bex bolt and _ocknut. Tighten securely.

2.Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

3, Position front wheels of the tractor so

they are pointing straight forward.

4.Remove steedng wheel adapter from steering wheel and slide adapter onto steering shaft extension.

5.Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

6.Assemble large flat washer, 3/8 Ioc washer, 3/8 hex bolt and lighten securely.

7.Snap steering wheel insert into cel of steedng wheel.

8.Remove protective matedals from

tractor hood and gdll. IMPORTANT: Check for and remove

staples in skid that may puncturetires where tractor is to rolloff skid.

HOWTO SET UPYOURTRACTOR

CHECK BATTERY

1. Lift seat pan to raised position end

open batterybox door.

NOTE: If this battery is put into service after month and year indicated on lab, (label located between terminals) cha battery for minimum of one hour at 6-1 amps. (See "BATTERY" in Maintenanc( section of this manual for charging instructions).

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Lawn Tractor For answers to your questionsLimited 90 DAY Warranty on Battery I1. Slope Operation General OperationMow only in daylight or good artificial light IV. Service Cancer and birth defects or other repro- ductive harm Productspecifications Ooo Before Removing Tractor from Skid Attachsteeringwheel Install Seat Lower seat into operating position and sit in seatInstall Mulcher Plate To Convertto Bagging or DischargingChecktire Pressure Check Deck LevelnessBattery Reverse Forward Fast Ammeter Indicates charging + or discharging of battery KnowyourtractorTo Adjust Mower Cutting Height Howto Useyourtractor To SET Parking BrakeStopping Ground DriveTo Adjust Gauge Wheels To Operate MowerTo Operate on Hills To TransportTowing Carts and Other Attachments Before Starting the Engine Check Engine OIL LevelADD Gasoline To Start EngineMulching Mowingtips Before Each USE Lubrication ChartGeneral Recommendations Tractor To Clean Battery and Terminals Clean AIR ScreenClean AIR INTAKE/COOLING Areas BeltsTo Service Cartridge AIR FilterEngine OIL Filter IN-LINE Fuel FilterCleaning To Install MowerTo Remove Mower Raise attachment lift lever to its highest positionTo Level Mower Housing SIDE-TO-SIDE AdjustmentTo Adjust Brake To Replace Mower Blade Drive BeltPulley To Replace Motion Drive BeltTransaxle Gear Shift Lever Neutral Adjustment To Start Engine with a Weak BatteryTo Adjust Steering Wheel ALIGN- Ment To Remove Wheel for RepairsReplacing Battery To Remove Hood and Grill AssemblyTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Throttle Control Cable To Adjust CarburetorTo Clean Battery and Termi TractorEngine Fuel System Engine OILTroubleshootingchart ProblemCause CorrectionTroubleshooting Chart Problem Cause Troubleshooting Chart Problem Cause CorrectionFor 30 seconds before Stopping engineSchematic TCR- Model NumberTRACTOR- -MODEL NUM BER Electrical TRACTOR-- Model Number Electrical NO. NO,DESCRIPTIONTractor - Model Number 917.272054 Chassis and Enclosures TRACTOR- -MODELNUMBER917.272054 Chassisandenclosures KEY Part NO, NO, DescriptionTRACTOR- -MODEL Number Ground Drive Shift Rate TRACTOR- Model Number Ground DriveX .1645/1865 TRACTOR--MODEL Number Steering Assembly TRACTOR- Model Number 917.272054 Steeringassembly KEY Part NO. NO.DESCRIPTIONTRACTOR--MODELNUMBER917.272054 Engine KEY Part DescriptionTRACTOR-- MODELNUMBER917.272054 Seatassembly DecaJ, V-Belt Schematic TRACTOR- Model Number DecalsWheels & Tires 99904TRACTOR- Model Number Liftassembly TRACTOR-- Model Number Mowerdeck TRACTORMODELNUMBER917--.272054 Mowerdeck STD693107Page TRACTOR--MODELNUMBER917.272054 PEERLESSTRANSAXLE- Model NUMBER206-545CRing Oil Seal 9 1Cylinder HEAD, Valve and Breaiieri Crankcasi Gasket 25-186-01-S14-0 Blower Housing Baffles KEY Part Descripon 25-086-47.SStarting System Engine Controls OIL PAN / Lubrication KEY Part NO. NO.DESCRIPTION Crankshaft Available ExhausPage Page Page Suggested Guide for Sighting Slopes for Safe Operation 3s6-7278 Sears,com/patsdirect 178457 2.20,01 RD

917.272054 specifications

The Craftsman 917.272054 is a robust and efficient riding lawn mower designed to make lawn maintenance a breeze. This machine features a powerful 24 HP Kohler engine, delivering reliable performance and significant torque, enabling it to tackle even the toughest grass and terrain with ease. One of the standout characteristics of the 917.272054 is its hydrostatic transmission, which offers smooth and variable speed control. This allows the operator to maneuver easily without the need for gear shifting, providing a more comfortable mowing experience.

Equipped with a 54-inch cutting deck, the Craftsman 917.272054 allows for a wide cutting path, significantly reducing mowing time, especially for larger lawns. The cutting deck features multiple height adjustments, ranging from 1.5 to 4 inches, allowing users to achieve the perfect cut tailored to the specific needs of their grass type. This adaptability promotes healthy grass growth and enhances the overall appearance of the lawn.

The mower also showcases a rugged and durable construction, making it suitable for various conditions. The front axle is designed for added stability, while the reinforced deck is engineered to withstand the rigors of frequent use. Another notable feature is the comfortable high-back seat that provides excellent lumbar support, essential for long mowing sessions.

For enhanced convenience, the Craftsman 917.272054 includes an easy-to-use dashboard with essential controls conveniently located for quick adjustments while operating. The ignition switch is designed for easy starting, and the mower includes a sturdy grass collection system for effortless cleaning and maintenance.

Additionally, this lawn mower is compatible with various attachments, including baggers, mulch kits, and other accessories, allowing users to customize their mowing experience based on their lawn care needs. Safety features like the operator presence control ensure that the mower will shut off if the operator leaves the seat, adding an extra layer of protection.

Overall, the Craftsman 917.272054 stands out as an exemplary choice for homeowners seeking a reliable and efficient lawn mower that combines power, functionality, and user-friendly design. With its advanced features and technologies, it makes lawn maintenance not only easier but also more enjoyable.
Top Page Image Contents