Craftsman 917.272054 owner manual Install Seat, Lower seat into operating position and sit in seat

Page 9

Door

INSTALL SEAT

Adjust seat before tightening adjustment knob,

1.Remove adjustment knob end fiat washer secudng seat to cardboard packing and set aside for assembly of seat to tractor.

2.Pivot seat upward and remove from the cardboard packing, Remove the cardboard packing and discard,

3.Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

4.Push down on seat to engage shoulder bolt in slot and pull seat towards roar of tractor.

5.Pivot seat and pan forward end assemble adjustment knob and fiat washer loosely. Do not tighten.

6.Lower seat into operating position and sit in seat,

7.Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal ell the way down.

8.Get off seat without moving its adjusted position.

9.Raise seat and tighten adjustment knob securely,

Seat

Bolt

Flat Washer

NOTE: You may now rollor drive your tractor off the skid. Follow the appropriate instructionbelow to remove the tractor from the skid.

TO ROLLTRACTOR OFF SKID (See Operation section for location and function of controls)

1.Press lift lever plunger and raise attachment lift lever to its highest position.

2.Release parking brake by depressing clutch/brake pedal.

3.Place gearshift lever in neutral {N) position,

4.Roll tractor forward off skid.

5.Remove banding holding deflector shield up against tractor.

TO DRIVETRACTOR OFF SKID (See Operation section for location and function of controls)

,_WARNING: Before starting, read, understand and follow all instructionsin

the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear

of other people and objects.

1.Be sure all the above assembly steps have been completed,

2.Check engine oil level and fill fuel tank with gasoline.

3.Sit on seat in operating position, depress elutch/brake pedal and set the parking brake.

4.Place gear shift lever in neulfal (N)

position.

5, Press lift lever plunger and raise attachment lift lever to its highest position.

6.Start the engine. After engine has started, move throttle control to idle position.

7.Depress clutch/broke pedal into full "BRAKE" position and hold. Move gearshift lever to 1st gear.

8.Slowly release clutch/brake pedal and slowly drive tractor off skid.

9.Apply brake to stop tractor, set parking brake and place gearshift lever in

neutral position.

10.Turn ignition key to "OFF" position.

Continue with the instructions that follow.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents For answers to your questions Lawn TractorLimited 90 DAY Warranty on Battery General Operation Mow only in daylight or good artificial lightI1. Slope Operation IV. Service Cancer and birth defects or other repro- ductive harm Productspecifications Ooo Before Removing Tractor from Skid Attachsteeringwheel Lower seat into operating position and sit in seat Install SeatTo Convertto Bagging or Discharging Install Mulcher PlateChecktire Pressure Check Deck LevelnessBattery Reverse Forward Fast Knowyourtractor Ammeter Indicates charging + or discharging of batteryHowto Useyourtractor To SET Parking Brake To Adjust Mower Cutting HeightStopping Ground DriveTo Operate Mower To Adjust Gauge WheelsTo Operate on Hills To TransportBefore Starting the Engine Check Engine OIL Level Towing Carts and Other AttachmentsADD Gasoline To Start EngineMulching Mowingtips Lubrication Chart General RecommendationsBefore Each USE Tractor Clean AIR Screen To Clean Battery and TerminalsClean AIR INTAKE/COOLING Areas BeltsAIR Filter To Service CartridgeEngine OIL Filter IN-LINE Fuel FilterTo Install Mower CleaningTo Remove Mower Raise attachment lift lever to its highest positionSIDE-TO-SIDE Adjustment To Level Mower HousingTo Replace Mower Blade Drive Belt To Adjust BrakePulley To Replace Motion Drive BeltTo Start Engine with a Weak Battery Transaxle Gear Shift Lever Neutral AdjustmentTo Adjust Steering Wheel ALIGN- Ment To Remove Wheel for RepairsTo Remove Hood and Grill Assembly Replacing BatteryTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Carburetor To Adjust Throttle Control CableTractor To Clean Battery and TermiEngine Fuel System Engine OILProblem TroubleshootingchartCause CorrectionTroubleshooting Chart Problem Cause Cause Correction Troubleshooting Chart ProblemFor 30 seconds before Stopping engineTCR- Model Number SchematicTRACTOR- -MODEL NUM BER Electrical NO. NO,DESCRIPTION TRACTOR-- Model Number ElectricalTractor - Model Number 917.272054 Chassis and Enclosures KEY Part NO, NO, Description TRACTOR- -MODELNUMBER917.272054 ChassisandenclosuresTRACTOR- -MODEL Number Ground Drive TRACTOR- Model Number Ground Drive X .1645/1865Shift Rate TRACTOR--MODEL Number Steering Assembly KEY Part NO. NO.DESCRIPTION TRACTOR- Model Number 917.272054 SteeringassemblyKEY Part Description TRACTOR--MODELNUMBER917.272054 EngineTRACTOR-- MODELNUMBER917.272054 Seatassembly TRACTOR- Model Number Decals DecaJ, V-Belt SchematicWheels & Tires 99904TRACTOR- Model Number Liftassembly TRACTOR-- Model Number Mowerdeck STD693107 TRACTORMODELNUMBER917--.272054 MowerdeckPage PEERLESSTRANSAXLE- Model NUMBER206-545C TRACTOR--MODELNUMBER917.272054Ring Oil Seal 9 1Cylinder HEAD, Valve and Breaiieri Crankcasi 25-186-01-S Gasket14-0 25-086-47.S Blower Housing Baffles KEY Part DescriponStarting System Engine Controls OIL PAN / Lubrication KEY Part NO. NO.DESCRIPTION Crankshaft Exhaus AvailablePage Page Page Suggested Guide for Sighting Slopes for Safe Operation 178457 2.20,01 RD 3s6-7278 Sears,com/patsdirect

917.272054 specifications

The Craftsman 917.272054 is a robust and efficient riding lawn mower designed to make lawn maintenance a breeze. This machine features a powerful 24 HP Kohler engine, delivering reliable performance and significant torque, enabling it to tackle even the toughest grass and terrain with ease. One of the standout characteristics of the 917.272054 is its hydrostatic transmission, which offers smooth and variable speed control. This allows the operator to maneuver easily without the need for gear shifting, providing a more comfortable mowing experience.

Equipped with a 54-inch cutting deck, the Craftsman 917.272054 allows for a wide cutting path, significantly reducing mowing time, especially for larger lawns. The cutting deck features multiple height adjustments, ranging from 1.5 to 4 inches, allowing users to achieve the perfect cut tailored to the specific needs of their grass type. This adaptability promotes healthy grass growth and enhances the overall appearance of the lawn.

The mower also showcases a rugged and durable construction, making it suitable for various conditions. The front axle is designed for added stability, while the reinforced deck is engineered to withstand the rigors of frequent use. Another notable feature is the comfortable high-back seat that provides excellent lumbar support, essential for long mowing sessions.

For enhanced convenience, the Craftsman 917.272054 includes an easy-to-use dashboard with essential controls conveniently located for quick adjustments while operating. The ignition switch is designed for easy starting, and the mower includes a sturdy grass collection system for effortless cleaning and maintenance.

Additionally, this lawn mower is compatible with various attachments, including baggers, mulch kits, and other accessories, allowing users to customize their mowing experience based on their lawn care needs. Safety features like the operator presence control ensure that the mower will shut off if the operator leaves the seat, adding an extra layer of protection.

Overall, the Craftsman 917.272054 stands out as an exemplary choice for homeowners seeking a reliable and efficient lawn mower that combines power, functionality, and user-friendly design. With its advanced features and technologies, it makes lawn maintenance not only easier but also more enjoyable.
Top Page Image Contents