Craftsman 917.27182 Warm Weather Starting 50 F and above, Slowly, Automatic Transmission Warm UP

Page 17

WARM WEATHER STARTING (50° F and above)

8.When engine starts, slowly push choke control in until the engine begins to run smoothly. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then continue to push the control

in slowly.

•The attachments and ground drive can now be used. If the engine does not accept the load, restartthe engine and allow it to

warm up for one minute usingthe choke as described above.

COLD WEATHER STARTING (50° F and below)

8.When engine starts, slowly push choke control in until the engine begins to run smoothly. Continue to push the choke control in small steps allowing the engine to accept small changes in speed and load, until the choke control is fully in. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then continue to push the control in slowly. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature.

AUTOMATIC TRANSMISSION WARM UP

Before driving the unit in cold weather, the transmission should be warmed up as follows:

1.Be sure the tractor is on level ground.

2.Place the motion control lever in neutral. Release the parking brake and let the clutch/brake slowly return to operating position.

3.Allow one minute for transmission to

warm up. This can be done during the engine warm up pedod.

•The attachments can be used during

the engine warm-up period after the transmission has been warmed up and may require the choke control be

pulled out slightly.

NOTE= If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See "TO ADJUST CARBURETOR" in the

Service and Adjustments section of this manual.

PURGETRANSMISSION

_CABTION: Never engage or disengage freewheel lever while the engine is running.

To ensure proper operation and perfor- mance, it is recommended that the

transmission be purged before operating tractor for the first time. This procedure wil! remove any trapped air inside the trans- mission which may have developed during shipping of your tractor.

IMPORTANT= Should your transmission require removal for service or replacement, it should be purged after reinstallation before operating the tractor.

1.Place tractor safely on level surface with engine off and parking brake set.

2.Disengage transmission by placing freewheel control in freewheeling position (See "TO TRANSPORT" in this section of manual).

3.Sitting in the tractor seat, start engine. After the engine is running, move throttle control to slow position. With motion control lever in neutral (N) position, slowly disengage clutch/ brake pedal.

4.Move motion control lever to full

forward position and hold for five (5) seconds. Move lever to full reverse

position and hold for five (5) seconds.

Repeat this procedure three (3) times. NOTE= During this procedure there will be no movement of ddve wheels. The air is

being removed from hydraulic ddve system.

5.Move motion control lever to neutral

(N)position. Shut- off engine and set parking brake.

6.Engage transmission by placing freewheel control in driving position (See "TO TRANSPORT" in this section of manual).

7.Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. With motion control lever in neutral (N) position, slowly disengage clutch/ brake pedal.

8.Slowly move motion control lever forward, after the tractor moves

approximately five (5) feet, slowly move motion control lever to reverse position. After the tractor moves approximately five (5) feet retum the motion control lever to the neutral (N)

position. Repeat this procedure with the motion control lever three (3) times.

Your tractor is now purged and now ready for normal operation.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents For answers to your questions About this product, Call IcrrftsmrniLimited 90 DAY Warranty on Battery Do not General OperationII. Slope Operation Iiichildren IV. ServiceThat may obscure vision Mower blades are sharp and can cutNeutral, you may lose control of the tractor Safety is InvolvedRepair Agreement Product SpecificationsKeys Video Cassette SeatOil DrainTube For FutureUseBefore Removing Tractor from Skid Attach Steering Wheel Install Seat If previously removed All assembly instructions have been #CHECKLISTENG,NEONENG,NEOFFOLFRESSUREL,G.TSONO%MF Knowyourtractor IndicatorClutch BrakePedal Height MotionHowto Useyourtractor To SET Parking Brake To Adjust Mower Cutting HeightStopping Mower Blades Ground DriveTo Operate Mower To Adjust Gauge WheelsTo Operate on Hills To TransportTowing Carts and Other Attachments Viscosity Chart in the Mainte- nance section of this manualBefore Stafitingthe Engine Check Engine OIL Level ADD GasouneSlowly Warm Weather Starting 50 F and aboveAutomatic Transmission Warm UP PurgetransmissionMulching Mowingtips MowingtipsAll adjustmentsin the Service Lubrication ChartGeneral Recommendations Zerk SpindleTires Brake OperationOperator Presence System Blade CareBelts To Clean Battery and TerminalsTransaxle Cooling Tranbaxle Pump FluidCartridge Aution Before Performing ANY Service or Adjustments CleaningTo Install Mower Tractor To Remove MowerSIDE-TO-SIDE Adjustment To Level Mower HousingTo Replace Mower Blade Drive Belt Belt RemovalTo Replace Motion Drive Belt To Adjust BrakeTransaxle Motion Control Lever Neutral Adjustment Replacing Battery To Adjust Steering WheelTo Start Engine with Weak TransmissionTo Adjust Throttle Control Cable To Remove Hood and Grill AssemblyTo Adjust Choke Control Interlocks and RelaysPreliminary Setting To Adjust CarburetorFinal Setting RPMTractor Problem Loose or damaged wiring Carburetor out of adjustmentDirty air filter Dirtyfuel filter Stale or dirtyfuelCause Troubleshooting ChartOrrection Replace blade Tighten blade boltPlace freewheel controlin BlownfuseEngaged position Replace motiondrive beltTractor -- Model Number SchematicTractor - Model Number ElectricalKEY Part Descripon ElectricalTractor - Model Number Chassis and Enclosures KEY Part NO. NO.DESCRIPTION Tractor - Model Number 917.271820 Chassis and EnclosuresGROUNDDRIVETRACTOR- MODELNUMBER917.271820 KEY Part Tractor -- Model Number 917,271820 Ground DriveTractor - Model Number 917.271820 Steering Assembly KEY Part Description Spark Arrester Tractor - Model Number 917,271820Optional Equipment KEY Paitt NO. NO.DESCRIPTION Tractor MODELNUMBER917.271820 SEAT AssEMBLYWheels & Tires DecalsTractor - Model Number Lift Assembly Lift Assembly Tractor . Model Number Tractor - Model Number Mower Deck 2629J Spacer\ \ 20w-50 11019LABELKIT LO. Ownersmanual2911 971I 934 TRACTOR-- MODELNUMBER917.271820803 797 544 801 5101 513 802 783 1051Gasket SET 634 1770 51A 16390569271411 272490 Page Page Only Ride UP and Down Hill Not Across Hill Suggested Guide for Sighting Slopes for Safe OperationRev 12.8.00 TR Get it fixed, at your home or ours

917.27182 specifications

The Craftsman 917.27182 is a versatile and reliable lawn tractor designed for homeowners who seek efficiency and ease in maintaining their yards. Known for its robust construction and innovative features, this lawn tractor is designed to handle a variety of tasks with ease.

One of the standout features of the Craftsman 917.27182 is its powerful engine. Equipped with a 17.5 HP Briggs & Stratton engine, this tractor provides plenty of power to tackle even the toughest mowing conditions. The engine is designed for smooth operation and is built for longevity, making it a dependable choice for lawn care.

The cutting deck of the Craftsman 917.27182 measures 42 inches, offering a wide cutting path that allows users to cover more ground in less time. The deck is made of durable materials, ensuring that it can withstand the rigors of regular use. Additionally, it features a multi-blade design that delivers a clean and precise cut, promoting healthy grass growth.

Another significant characteristic of this lawn tractor is its 6-speed transmission. The automatic transmission allows for smooth shifting between gears, providing users with the flexibility to adjust their speed based on the terrain and grass height. This feature enhances maneuverability and improves overall mowing efficiency.

The Craftsman 917.27182 is equipped with a comfortable and ergonomic seat, designed to reduce fatigue during extended use. The seat can be easily adjusted to accommodate different user heights, ensuring optimal comfort for everyone. Furthermore, the tractor has a tight turning radius, making it easy to navigate around obstacles and flower beds.

In terms of technological advancements, this model incorporates a robust front axle and durable rear wheels, designed for stability and traction. The inclusion of easy-access controls allows users to operate the tractor without difficulty, enhancing the overall user experience.

Maintenance is made simple with the Craftsman 917.27182, as it features an easily accessible oil filter and fuel tank, allowing for hassle-free servicing. This focus on convenience extends to the design of the mower deck, which can be tilted for easier cleaning after use.

Overall, the Craftsman 917.27182 lawn tractor combines power, durability, and user-friendly features to create an impressive tool for lawn care. Its blend of technology and thoughtful design makes it a reliable choice for any homeowner looking to maintain a beautiful lawn with minimal effort.
Top Page Image Contents