Craftsman 917.27182 Brake Operation, Tires, Operator Presence System, Blade Care, Blade Removal

Page 20

TRACTOR

Always observe safety rules when performing any maintenance.

BRAKE OPERATION

If tractor requires more than six (6) feet

stopping distance at high speed in highest gear, then brake must be ad- justed, (_ee "TO ADJUST BRAKE" in the

Service and Adjustments section of this

manual).

TIRES

•Maintain proper air pressure in all tires (See "PRODUCT SPECIFICATIONS" section of this manual).

•Keep tiros free of gasoline, oil, or insect control chemicals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects andother hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant

may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are working properly. If your tractor does not function as described,

repair the problem immediately.

•The engine should not start unless the clutch/brake pedal is fully depressed and attachement clutch control is In the

disengaged position.

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never

operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be

kept sharp. Replace bent or damaged blades.

BLADE REMOVAL

1.Raise mower to highest position to allow access to blades.

2.Remove hex bolt, lock washer and flat washer securing blade.

3.Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

4.Reassemble hex bolt, lock washer and flat washer in exact order as shown.

5.Tighten bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: Blade bolt is grade 8 heat treated.

TraitincEdgeUp Mandrel Assembly

Blade Center Hole

Flat Washer.

Lock Washe

_'Hex Bok

*A Grade 8 heat treated boltcan be identified by six lineson the bolt head.

TO SHARPEN BLADE

NOTE; We do not recommend sharpen-

ir_ blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will

cause excessive vibration and eventual damage to mower and engine.

•The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone

balancer. (When using a cone bal- ancer, follow the instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade, The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded

portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen

the heavy end until the blade is balanced.

,/

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. How-

ever, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep smal vent holes open.

20* Recharge at 6-10 amperes for 1 hour.

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Icrrftsmrni For answers to your questions About this product, CallLimited 90 DAY Warranty on Battery Do not General OperationII. Slope Operation IV. Service IiichildrenThat may obscure vision Mower blades are sharp and can cutSafety is Involved Neutral, you may lose control of the tractorProduct Specifications Repair AgreementSeat Keys Video CassetteOil DrainTube For FutureUseBefore Removing Tractor from Skid Attach Steering Wheel Install Seat If previously removed #CHECKLIST All assembly instructions have beenENG,NEONENG,NEOFFOLFRESSUREL,G.TSONO%MF Indicator KnowyourtractorClutch BrakePedal Height MotionTo Adjust Mower Cutting Height Howto Useyourtractor To SET Parking BrakeStopping Mower Blades Ground DriveTo Adjust Gauge Wheels To Operate MowerTo Operate on Hills To TransportViscosity Chart in the Mainte- nance section of this manual Towing Carts and Other AttachmentsBefore Stafitingthe Engine Check Engine OIL Level ADD GasouneWarm Weather Starting 50 F and above SlowlyAutomatic Transmission Warm UP PurgetransmissionMowingtips Mulching MowingtipsLubrication Chart All adjustmentsin the ServiceGeneral Recommendations Zerk SpindleBrake Operation TiresOperator Presence System Blade CareTo Clean Battery and Terminals BeltsTransaxle Cooling Tranbaxle Pump FluidCartridge Cleaning Aution Before Performing ANY Service or AdjustmentsTo Install Mower Tractor To Remove MowerTo Level Mower Housing SIDE-TO-SIDE AdjustmentTo Replace Mower Blade Drive Belt Belt RemovalTo Replace Motion Drive Belt To Adjust BrakeTransaxle Motion Control Lever Neutral Adjustment To Adjust Steering Wheel Replacing BatteryTo Start Engine with Weak TransmissionTo Remove Hood and Grill Assembly To Adjust Throttle Control CableTo Adjust Choke Control Interlocks and RelaysTo Adjust Carburetor Preliminary SettingFinal Setting RPMTractor Loose or damaged wiring Carburetor out of adjustment ProblemDirty air filter Dirtyfuel filter Stale or dirtyfuelTroubleshooting Chart CauseOrrection Replace blade Tighten blade boltBlownfuse Place freewheel controlinEngaged position Replace motiondrive beltSchematic Tractor -- Model NumberElectrical Tractor - Model NumberElectrical KEY Part DescriponTractor - Model Number Chassis and Enclosures Tractor - Model Number 917.271820 Chassis and Enclosures KEY Part NO. NO.DESCRIPTIONGROUNDDRIVETRACTOR- MODELNUMBER917.271820 Tractor -- Model Number 917,271820 Ground Drive KEY PartTractor - Model Number 917.271820 Steering Assembly KEY Part Description Spark Arrester Tractor - Model Number 917,271820Optional Equipment KEY Paitt NO. NO.DESCRIPTION SEAT AssEMBLY Tractor MODELNUMBER917.271820Decals Wheels & TiresTractor - Model Number Lift Assembly Lift Assembly Tractor . Model Number Tractor - Model Number Mower Deck Spacer 2629J\ \ 20w-50 11019LABELKIT LO. Ownersmanual2911 TRACTOR-- MODELNUMBER917.271820 971I 9345101 513 802 783 1051 803 797 544 801Gasket SET 634 1770 51A 16390569271411 272490 Page Page Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across HillGet it fixed, at your home or ours Rev 12.8.00 TR

917.27182 specifications

The Craftsman 917.27182 is a versatile and reliable lawn tractor designed for homeowners who seek efficiency and ease in maintaining their yards. Known for its robust construction and innovative features, this lawn tractor is designed to handle a variety of tasks with ease.

One of the standout features of the Craftsman 917.27182 is its powerful engine. Equipped with a 17.5 HP Briggs & Stratton engine, this tractor provides plenty of power to tackle even the toughest mowing conditions. The engine is designed for smooth operation and is built for longevity, making it a dependable choice for lawn care.

The cutting deck of the Craftsman 917.27182 measures 42 inches, offering a wide cutting path that allows users to cover more ground in less time. The deck is made of durable materials, ensuring that it can withstand the rigors of regular use. Additionally, it features a multi-blade design that delivers a clean and precise cut, promoting healthy grass growth.

Another significant characteristic of this lawn tractor is its 6-speed transmission. The automatic transmission allows for smooth shifting between gears, providing users with the flexibility to adjust their speed based on the terrain and grass height. This feature enhances maneuverability and improves overall mowing efficiency.

The Craftsman 917.27182 is equipped with a comfortable and ergonomic seat, designed to reduce fatigue during extended use. The seat can be easily adjusted to accommodate different user heights, ensuring optimal comfort for everyone. Furthermore, the tractor has a tight turning radius, making it easy to navigate around obstacles and flower beds.

In terms of technological advancements, this model incorporates a robust front axle and durable rear wheels, designed for stability and traction. The inclusion of easy-access controls allows users to operate the tractor without difficulty, enhancing the overall user experience.

Maintenance is made simple with the Craftsman 917.27182, as it features an easily accessible oil filter and fuel tank, allowing for hassle-free servicing. This focus on convenience extends to the design of the mower deck, which can be tilted for easier cleaning after use.

Overall, the Craftsman 917.27182 lawn tractor combines power, durability, and user-friendly features to create an impressive tool for lawn care. Its blend of technology and thoughtful design makes it a reliable choice for any homeowner looking to maintain a beautiful lawn with minimal effort.
Top Page Image Contents