Craftsman 917.27182 manual To Level Mower Housing, SIDE-TO-SIDE Adjustment, Belt Removal

Page 24

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or ddveway. Make sure tires are propedy inflated (See "PROD-

UCT SPECIFICATIONS" section of this manual). If tiros are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of

mower to ground. Distance =A" on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To _ower one side ol mower, loosen lift

link adjustment nut on that side. NOTE:Each full turn of adjustment nut

wilt change mower height about 1/8".

•Recheck measurements alter adjust-

ing.

 

Bottomedge of

Bottomedge of

mower_round

(_G SuspensionArm

LiftLinkAdjustmentNutI"

FRONT-TO-BACK ADJUSTMENT IMPORTANT: Deck must be level side-to

side. If the following front-to-beck adjustment is necessary, be sure to adjust both front links equally so mower will stay level side-to-side.

To obtain the best cutting results, the mower housing should be adjusted so

that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in

its highest position.

Check adjustment on right side of tractor. Measure distance =D" directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before makin 9 any necessary adjust- ments, check that both front links are equal in length, Both links should be approximately 10-3/8".

•If links are not equal in length, adjust

one link to same length as other link.

•To lower front of mower loosen nut "E"

on both front links an equal number of turns.

•When distance "D" is 1/8" to 1/2" lower at front than rear, tighten nuts "F" against trunnion on both front links.

•To raise front of mower, loosen nut "F" from trunnion on both front links.

Tighten nut =E" on both front links an equal number of turns.

•When distance "D" is 1/8" to 1/2" lower

at front than rear, tighten nut =F" against trunnion on both front links.

•Recheck side-to-side adjustment.

%_,_" _. oj/Mandrel

I"o"

Both FrontUnks Shouldbe Equal in Length

Nut "F"_

Nut "E"

"Trsnnion f_

Front Links

TO REPLACE MOWER BLADE DRIVE BELT

The mower blade ddve belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

1.Remove mower from tractor (See "TO REMOVE MOWER" in this section of this manual).

2.Work belt off both mandrel pulleys and idler pulleys.

3.Pull belt away from mower.

BELT INSTALLATION -

4.Install new belt in reverse order of removal.

5.Make sure belt is in all pulley grooves and inside all belt guides.

6.Install mower in reverse order of removal instructions.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Icrrftsmrni For answers to your questions About this product, CallLimited 90 DAY Warranty on Battery General Operation II. Slope OperationDo not IV. Service IiichildrenThat may obscure vision Mower blades are sharp and can cutSafety is Involved Neutral, you may lose control of the tractorProduct Specifications Repair AgreementSeat Keys Video CassetteOil DrainTube For FutureUseBefore Removing Tractor from Skid Attach Steering Wheel Install Seat If previously removed #CHECKLIST All assembly instructions have beenENG,NEONENG,NEOFFOLFRESSUREL,G.TSONO%MF Indicator KnowyourtractorClutch BrakePedal Height MotionTo Adjust Mower Cutting Height Howto Useyourtractor To SET Parking BrakeStopping Mower Blades Ground DriveTo Adjust Gauge Wheels To Operate MowerTo Operate on Hills To TransportViscosity Chart in the Mainte- nance section of this manual Towing Carts and Other AttachmentsBefore Stafitingthe Engine Check Engine OIL Level ADD GasouneWarm Weather Starting 50 F and above SlowlyAutomatic Transmission Warm UP PurgetransmissionMowingtips Mulching MowingtipsLubrication Chart All adjustmentsin the ServiceGeneral Recommendations Zerk SpindleBrake Operation TiresOperator Presence System Blade Care To Clean Battery and Terminals Belts Transaxle Cooling Tranbaxle Pump FluidCartridge Cleaning Aution Before Performing ANY Service or AdjustmentsTo Install Mower Tractor To Remove MowerTo Level Mower Housing SIDE-TO-SIDE AdjustmentTo Replace Mower Blade Drive Belt Belt RemovalTo Adjust Brake Transaxle Motion Control Lever Neutral AdjustmentTo Replace Motion Drive Belt To Adjust Steering Wheel Replacing BatteryTo Start Engine with Weak TransmissionTo Remove Hood and Grill Assembly To Adjust Throttle Control CableTo Adjust Choke Control Interlocks and RelaysTo Adjust Carburetor Preliminary SettingFinal Setting RPMTractor Loose or damaged wiring Carburetor out of adjustment ProblemDirty air filter Dirtyfuel filter Stale or dirtyfuelTroubleshooting Chart CauseOrrection Replace blade Tighten blade boltBlownfuse Place freewheel controlinEngaged position Replace motiondrive beltSchematic Tractor -- Model NumberElectrical Tractor - Model NumberElectrical KEY Part DescriponTractor - Model Number Chassis and Enclosures Tractor - Model Number 917.271820 Chassis and Enclosures KEY Part NO. NO.DESCRIPTIONGROUNDDRIVETRACTOR- MODELNUMBER917.271820 Tractor -- Model Number 917,271820 Ground Drive KEY PartTractor - Model Number 917.271820 Steering Assembly KEY Part Description Tractor - Model Number 917,271820 Optional EquipmentSpark Arrester KEY Paitt NO. NO.DESCRIPTION SEAT AssEMBLY Tractor MODELNUMBER917.271820Decals Wheels & TiresTractor - Model Number Lift Assembly Lift Assembly Tractor . Model Number Tractor - Model Number Mower Deck Spacer 2629J\ \ 20w-50 LO. Ownersmanual 291111019LABELKIT TRACTOR-- MODELNUMBER917.271820 971I 9345101 513 802 783 1051 803 797 544 801Gasket SET 634 1770 51A 16390569271411 272490 Page Page Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across HillGet it fixed, at your home or ours Rev 12.8.00 TR
Top Page Image Contents