Craftsman 917.27113 To Level Mower Housing, SIDE-TO-SIDE Adjustment, FRONT-TO-BACK Adjustment

Page 21

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires areproperly inflated (See "PROD-

UCT SPECIFICATIONS" section of this manual). If tires are over or

underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance =A" on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift

link adjustment nut on that side.

NOTE: Each full tum of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjust- ing.

Bottom edge of

_

Bottom edge o!

mower to

mower to

ground _

 

ground

A7- /GroundUne

Arm

•=e@

Lift Unk N_

Adjustment

FRONT-TO-BACK ADJUSTMENT

IMPORTANT: Deck must be level side-toside. If the following front-to-beck adjustment is necessary, be sure to adjust beth front links equally so mower will stay level side-to-side.

To obtain the best cutting results, the mower housing should be adjusted so

that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in

its highest position.

Check adjustment on right side of tractor. Measure distance =D" directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjust- ments, check that both front links are

equal in length. Both links should be approximately 10-3/8".

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut "E"

on both front links an equal number of turns.

•When distance =D" is 1/8" to 1/2" lower at front than rear, tighten nuts "F" against trunnion on both front links.

•To raise front of mower, loosen nut =F" from trunnion on both front links. Tighten nut =E" on both front links an equal number of turns.

•When distance "D" is 1/8" to 1/2" lower at front than rear, tighten nut "F* against trunnion on both front links.

•Recheck side,to-side adjustment.

- _\_ - oot / Mandrel

o

o o

Both Front Links Should be Equal in Length

Front Unks

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Rrftsmrw Service Adjustments Safety General Operation Slope OperationChildren Service Customer Responsibilities Repair AgreementSteering Wheel HOW to SET UP Your Tractor Tools Required for AssemblyTo Remove Tractor from Carton Unpack CartonTo Drive Tractor OFF Skid Install SeatTo Convert to Bagging or Discharging Please Review the Following ChecklistCheck Tire Pressure Check Deck LevelnessH L c Knowyourtractor National Standards InstituteTo USE Throttle Control HOW to USE Your TractorTo Operate on Hills To Operate MowerTo Transport Before Starting the Engine Towing Carts and Other AttachmentsTo Start Engine Check Engine OIL LevelMulching Mowing Tips Mowing TipsLubrication Chart General RecommendationsBefore Each USE Blade Removal To Sharpen BladeTransaxle Cooling Clean AIR ScreenBelts Engine LubricationEngine OIL Filter To Service PRE-CLEANERMuffler Spark PlugsTo Install Mower CleaningTractor To Remove MowerTo Level Mower Housing SIDE-TO-SIDE AdjustmentFRONT-TO-BACK Adjustment Belt Installation To Adjust BrakeTo Replace Motion Drive Belt To Replace Mower Blade Drive BeltFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel AlignmentTo Remove Wheel for Repairs To Attach Jumper CablesReplacing Battery To Remove Hood and Grill AssemblyTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Carburetor Engine To Adjust Throttle Control CableAcceleration Test Engine Troubleshooting Problem Chart CauseCorrection Correction Troubleshooting Chart Problem CauseTroubleshooting Chart ProblemcauseOFF Tractor - Model Number SchematicElectrical KEY Part Description Tractor -- Model Number ElectricalTractor --MODEL Number Chassis and Enclosures Tractor - Model Number 917.271130 Chassis and Enclosures Tractor - Model Number Ground Drive Ground Drive KEY Part Description Tractor Model Number 917,271130Tractor -- Model Number 917.271130 Steeringassembly TRACTOR-- Model Number 917.271130 Steering Assembly Tractor -- Model Number Engine KEY Part Tractor - Model Number Seatassembly Wheels & Tires KEY Part Description DecalsTractor -- Model Number Lift Assembly Tractor --MODEL Number Lift Assembly Tractor - Model Number Mower Deck UNC KEY Part NO, no157 TRACTOR-- Model Number Peerless TRANSAXLE--MODELNUMBER20545C REF Part NO. noPart Description Cylinder HEAD, Valve and Breather Cylinder HEADNALVF.JBREATHERCRANKCASE KEY Part Description Ignition / Electrical Blower Housing and Baffles 25-154-02 Starting System Ehgihe Controls OIL PAN / Lubrication Starting System Engine Controls KEY Part NO. NO.DESCRIPTION OIL PanilubricationKEY Part NO. no Crahkhaft Description Fuel System Crankshaft KEY Part DescriptionPage Only Ride UP and Down Hill Not Across HillSighting Guide HomeCnt

917.27113 specifications

The Craftsman 917.27113 is a riding lawn mower that has garnered attention for its robust features, user-friendly design, and performance efficiency. This model is particularly well-suited for homeowners with large yards, delivering strong cutting power and ease of use.

One of the standout features of the Craftsman 917.27113 is its powerful engine. Equipped with a reliable 17.5 HP Briggs & Stratton engine, this riding mower provides ample power for mowing through thick grass and uneven terrain. The engine’s design ensures consistent performance, while the automatic transmission allows for smooth and effortless acceleration, making it simple to navigate various landscapes.

The cutting deck is another significant aspect of the Craftsman 917.27113. It features a 42-inch cutting deck, making it ideal for mowing large areas efficiently. The cutting height can be adjusted to multiple positions, allowing users to customize their lawn maintenance according to the season or personal preference. The blade engagement system is easy to use, enabling quick activation of the blades without the hassle of manual adjustments.

In terms of comfort, the Craftsman 917.27113 was designed with the user in mind. It boasts a comfortable high-back seat that offers support during prolonged mowing sessions. The ergonomically designed steering wheel ensures that users can navigate effortlessly, even in tight corners. The spacious foot area adds to the overall comfort, allowing for a more relaxed mowing experience.

Another notable technology in this model is the mulching capability. With the optional mulch plug, users can convert the mower to recycle grass clippings back into the lawn, promoting healthier grass while reducing the need for bagging. This eco-friendly feature not only helps in maintaining a nutrient-rich lawn but also simplifies post-mowing clean-up.

Safety is a priority in the Craftsman 917.27113, with features like the blade brake that stops the blades when the operator leaves the seat. This ensures that users remain safe while operating the mower. The design also incorporates sturdy construction materials that enhance the mower’s durability, making it a worthwhile investment for long-term lawn care.

Overall, the Craftsman 917.27113 delivers a blend of power, comfort, and technology. Its robust performance, customizable cutting options, and user-friendly features make it an excellent choice for homeowners looking to keep their lawns in pristine condition. Whether for regular mowing or tackling overgrown areas, this riding mower stands out as a reliable and effective tool in lawn maintenance.
Top Page Image Contents