Craftsman 917.27113 To Replace Headlight Bulb, Interlocks and Relays, Replacing Battery

Page 24

PositiveTerminal NegativeTerminal

Positive Terminal

Negative Terminal

REPLACING BATTERY

CAUTION: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch

bands,rings,etc.

Positive terminal must be connected first to prevent sparking from accidental grounding.

•Lift seat pan to raised position and open battery box door.

•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with hex bolt and nut as shown. Tighten securely.

•Connect BLACK grounding cable to negative (-) terminal with remaining hex bolt and nut. Tighten securely.

•Close battery box door.

Battery

Door

Hex

Nut

Positive (Red) Cable Negative (Black) Cable

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 15 amp automotive-type

plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

Hood

_eadlight rWire

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Rrftsmrw Service Adjustments Safety General Operation Slope OperationChildren Service Repair Agreement Customer ResponsibilitiesSteering Wheel Tools Required for Assembly HOW to SET UP Your TractorTo Remove Tractor from Carton Unpack CartonInstall Seat To Drive Tractor OFF SkidPlease Review the Following Checklist To Convert to Bagging or DischargingCheck Tire Pressure Check Deck LevelnessH L c National Standards Institute KnowyourtractorHOW to USE Your Tractor To USE Throttle ControlTo Operate on Hills To Operate MowerTo Transport Towing Carts and Other Attachments Before Starting the EngineTo Start Engine Check Engine OIL LevelMowing Tips Mulching Mowing TipsLubrication Chart General RecommendationsBefore Each USE To Sharpen Blade Blade RemovalClean AIR Screen Transaxle CoolingBelts Engine LubricationTo Service PRE-CLEANER Engine OIL FilterMuffler Spark PlugsCleaning To Install MowerTractor To Remove MowerTo Level Mower Housing SIDE-TO-SIDE AdjustmentFRONT-TO-BACK Adjustment To Adjust Brake Belt InstallationTo Replace Motion Drive Belt To Replace Mower Blade Drive BeltTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Remove Wheel for Repairs To Attach Jumper CablesTo Remove Hood and Grill Assembly Replacing BatteryTo Replace Headlight Bulb Interlocks and RelaysEngine To Adjust Throttle Control Cable To Adjust CarburetorAcceleration Test Engine Troubleshooting Problem Chart CauseCorrection Troubleshooting Chart Problem Cause CorrectionTroubleshooting Chart ProblemcauseOFF Schematic Tractor - Model NumberElectrical Tractor -- Model Number Electrical KEY Part DescriptionTractor --MODEL Number Chassis and Enclosures Tractor - Model Number 917.271130 Chassis and Enclosures Tractor - Model Number Ground Drive Tractor Model Number 917,271130 Ground Drive KEY Part DescriptionTractor -- Model Number 917.271130 Steeringassembly TRACTOR-- Model Number 917.271130 Steering Assembly Tractor -- Model Number Engine KEY Part Tractor - Model Number Seatassembly Decals Wheels & Tires KEY Part DescriptionTractor -- Model Number Lift Assembly Tractor --MODEL Number Lift Assembly Tractor - Model Number Mower Deck KEY Part NO, no UNC157 TRACTOR-- Model Number Peerless TRANSAXLE--MODELNUMBER20545C REF Part NO. noPart Description Cylinder HEAD, Valve and Breather Cylinder HEADNALVF.JBREATHERCRANKCASE KEY Part Description Ignition / Electrical Blower Housing and Baffles 25-154-02 Starting System Ehgihe Controls OIL PAN / Lubrication Starting System Engine Controls KEY Part NO. NO.DESCRIPTION OIL PanilubricationKEY Part NO. no Crahkhaft Fuel System Crankshaft KEY Part Description DescriptionPage Only Ride UP and Down Hill Not Across HillSighting Guide HomeCnt

917.27113 specifications

The Craftsman 917.27113 is a riding lawn mower that has garnered attention for its robust features, user-friendly design, and performance efficiency. This model is particularly well-suited for homeowners with large yards, delivering strong cutting power and ease of use.

One of the standout features of the Craftsman 917.27113 is its powerful engine. Equipped with a reliable 17.5 HP Briggs & Stratton engine, this riding mower provides ample power for mowing through thick grass and uneven terrain. The engine’s design ensures consistent performance, while the automatic transmission allows for smooth and effortless acceleration, making it simple to navigate various landscapes.

The cutting deck is another significant aspect of the Craftsman 917.27113. It features a 42-inch cutting deck, making it ideal for mowing large areas efficiently. The cutting height can be adjusted to multiple positions, allowing users to customize their lawn maintenance according to the season or personal preference. The blade engagement system is easy to use, enabling quick activation of the blades without the hassle of manual adjustments.

In terms of comfort, the Craftsman 917.27113 was designed with the user in mind. It boasts a comfortable high-back seat that offers support during prolonged mowing sessions. The ergonomically designed steering wheel ensures that users can navigate effortlessly, even in tight corners. The spacious foot area adds to the overall comfort, allowing for a more relaxed mowing experience.

Another notable technology in this model is the mulching capability. With the optional mulch plug, users can convert the mower to recycle grass clippings back into the lawn, promoting healthier grass while reducing the need for bagging. This eco-friendly feature not only helps in maintaining a nutrient-rich lawn but also simplifies post-mowing clean-up.

Safety is a priority in the Craftsman 917.27113, with features like the blade brake that stops the blades when the operator leaves the seat. This ensures that users remain safe while operating the mower. The design also incorporates sturdy construction materials that enhance the mower’s durability, making it a worthwhile investment for long-term lawn care.

Overall, the Craftsman 917.27113 delivers a blend of power, comfort, and technology. Its robust performance, customizable cutting options, and user-friendly features make it an excellent choice for homeowners looking to keep their lawns in pristine condition. Whether for regular mowing or tackling overgrown areas, this riding mower stands out as a reliable and effective tool in lawn maintenance.
Top Page Image Contents