Craftsman LTS 1500 To Remove CABLES, Reverse Order, Replacing Battery, Interlocks and Relays

Page 25

TO REMOVE CABLES, REVERSE ORDER -

1. BLACK cable first from chassis and then from the fully charged battery..

2, RED cable last from both batteries.

Weak or Dead

Fully Charged

Battery

 

Battery

REPLACING

BATTERY

_,WARNING:

Do

not Short battery termi-

nals by allowing a wrench or any other object to contact both terminals at the same time.

Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental ground- lng.

I.. Lift seat pan to raised position..

2 Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor..

3Install new battery with terminals in same position as old battery.

4First connect RED battery cable to posi- tive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal

5.Connect BLACK grounding cable to negative (-) terminal with remaining hex bolt and keps nut, Tighten securely.

3.Replace bulb in holder and push bulb 17older securely back into the hole in the backside of the grill.

4.Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting

• Check wiring. See electrical wiring dia- gram in the Repair Parts section

TO REPLACE FUSE

Replace with 20 amp automotive-type plug- in fuse. The fuse holder' is located behind

the dash_

TO REMOVE HOOD AND GRILL AS- SEMBLY

1 Raise hood.

2Unsnap headlight wire connector

3Stand in front of tractor. Grasp hood at

sides, tilt toward engine and lift off of tractor

4When replacing hood, be sure to recon- nect the headlight wire connector.

\Hood

i

"\

/\

 

/

_',

/_".

Headlight Wire

/ ..

 

" .// .--..'.

Connector

.

,

 

t

Seat _an--__...__ 1_

_.,IR

_,

_::i::::lfLabel

ICi!,:..............

/_!

IC..Keps

Terminal

Hex

Bolt

Posi (Red)

CableNegative (Black) Cable

TO REPLACE HEADLIGHT BULB t_ Raise hood

2.Pull bulb holder out of the hole in the backside of the grill°

ENGINE

Maintenance, repair, or replacement of the emission control devices and systems, which are being done atthe customers expense, may be performed by any non-road engine repair establishment or individual. Warranty repairs must be performed by an authorized engine manufacturer's service outlet,

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be neces-_ sary. Check adjustment as described below before loosening cable,. If adjustment is necessary, proceed as follows:

IWith engine not running, move throttle control lever from slowto choke position Slowly move lever from choke to fast

25position

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Sears Craftsman Help Line Lawn TractorDays on Battery Craftsman Limited Warranty TWO Years on TractorGeneral Operation II. Slope Operation Service Safe Handling of GasolineIV, Towing General Service SAE ProductAPI-SG-SL SAE RC12YCKeys T1!f1111Assemble Extension Shaft and Boot Tools Required for AssemblyInstall Steering Wheel Install SeatTo Roll Tractor OFF Skid Check BatteryCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake System@@@@ Reverse Operation System ROS Know Your TractorTo SET TractorTo Operate Mower Using the Reverse Operation SystemOperating in Reverse To Operate on HillsBefore Starting the Engine Check Engine OIL Level Towing Carts and Other ATTACH- MentsADD Gasoline To Start EngineMowing Tips Lubrication Chart MaintenanceEVE.Y Every Every SEFO.E Schedule EachBlade Removal Blade CareTo Clean Battery and Terminals BatteryTransaxle Cooling LubricationClean AIR Screen CleaningIN-LINEFUEL Filter AIR FilterTo Remove Mower To Install Mower SIDE-TO-SIDE Adjustment To Level Mower Housing FRONT-TO-BACK Adjustment To Replace Mower Blade Drive Belt Belt InstallationBelt Removal To Check BrakeMent To Adjust Throttle Control Cable Replacing BatteryTo Remove CABLES, Reverse Order Interlocks and RelaysPreliminary Setting To Adjust CarburetorFinal Setting Acceleration TestFuel System TractorEngine OIL CylindersWill Problem Cause CorrectionLoss of power ProblemEngine clicks but Cause CorrectionBattery will not charge Problem CausecorrectionPoor grass discharge When EngineOFF 11 n 11 o 11I BiAS Para BATERiAS Lesiones graves o la muerte Generales IV, RemolquePage MIN. CCA DEL ProductoPage EL Montaje Para Hacer Rodar EL Tractor Verifique LA BATER1ALlantas Revision DE LA Presion DE LASRevision DE LA Posicion ADECUA- DA DE Todas LAS Correas Lista DE Revision@@@@ Control DE Aceleracion Faiviliaricese CON SU TractorMacho DE LA Palanca DE Levanta Palanca DEL Embrague DEL AccesoMiento Para Parar LAS Cuchillas DE LA Sega Papa Operar LA SegadoraUsar EL Sistema DE FUNC1ONAMIENTO Atras Para Operar EN CerrosAntes DE Hacer Arrancar EL Remolque DE Carretillas O Otros AccesoriosMotor Agregue GasolinaConsejos Para Segar Oo272Mantenimiento Generales TablaSistema Presencia Operador Y Siste LlantasMA FUNCIONArIENTO Atras ROS Verifiez Sistema Presencia OperadorNales BateriaEnfriamiento DEL Transeje CorreasFiltro DE Aire Filtro DE Aceite DI=L MotorLimpieza DE LA Rejilla Dieaire Filtro DE Combustible EN LineaTractor Para Remover LA Segadora SERVIClO O DE Hacer AjustesPara Instalar LA Segadora Ajuste DE Lado a Lado Para Nivelar LA Caja DE LA SEGA- DoraAjuste Desde Adelante Hacia Atras Segadora LA Correa DE ImpulsionReles Prueba DE LA Aceleraciqn Ajuste FinalOtros Aceite DEL MotorCausa Sears PROBLEIViAPero noarranca Prdida de fuerza Continuado P6rdida de fuerzaEl tractor se pon en marcha arras El motor continua funcionan do Cuando el operadorLas cuchiltas segadoras no rotan SearsC6sped Las luz ces delanteras no El motor tieneSoline Genera Rrt 17.5 F
Top Page Image Contents