TROUBLESHOOTING CHART:
See appropriate section in manual unless directed to Sears service center
PROBLEM
Engine clicks but
will not start
Loss of power
Loss of power
iExcessive vibration
| CAUSE |
|
|
| CORRECTION | |||
1 | Weak | or dead | battery | 1 | Recharge or replace battery | |||
2 | Corroded battery terminals. | 2 | Clean | battery | terminals | |||
3 | Loose | or damaged | wiring. | 3 | Check | all wiring | ||
4 | Faulty | solenoid | or | starter. | 4 | Checldreplace | solenoid or starte_ |
1Cutting too much grassftoo fast.. 1 Raise cutting height/reduce speed
2 | Throttle | in "CHOKE" position. | 2 | Adjust | throttle control |
| ||||||||
3 | of grass, | leaves and | 3 | Clean | underside | of mower |
| |||||||
| trash | under | mower:. |
| housing |
|
|
|
| |||||
4 | Dirty | air | filter |
|
|
| 4 | Cleanlreplace | air | filter |
| |||
5 | Low oil | leveltdirty | oil | 5 | Check | oil leveltchange oil |
| |||||||
6 | Faulty spark | plug, |
| 6 | Clean and regap or change spark | |||||||||
|
|
|
|
|
|
|
|
| plug |
|
|
|
|
|
7 | Dirty | fuel filter |
|
| 7 | Replace | fuel | filter |
| |||||
8 | Stale | or | dirty | fuel |
| 8 | Empty fuel tank and refill tank with | |||||||
|
|
|
|
|
|
|
|
| fresh, | clean | gasoline° |
| ||
9 | Water | in fuel |
|
|
| 9 | Empty fuel tank and carburetor, | |||||||
|
|
|
|
|
|
|
|
| refill tank with fresh gasoline and | |||||
|
|
|
|
|
|
|
|
| replace | fuef | filter |
|
| |
!0 | Spark | plug | wire | loose | I0 | Connect | and tighten spark | plug | ||||||
|
|
|
|
|
|
|
|
| wire |
|
|
|
|
|
1t | Dirty | engine |
| air | screenlfins | 11 | Clean | engine | air screen/fins, |
| ||||
12 | Dirtytclogged | muffler | 12 | Cleantreplace | muffler |
| ||||||||
13 | Loose or damaged | wiring | 13 | Check | all wiring |
|
| |||||||
14 | Carburetor | out | of adjustment | 14 | See "To Adjust Carburetor" | in | ||||||||
|
|
|
|
|
|
|
|
| Service | and | Adjustments sectien |
15Engine valves out of adjustment 15 Contact a Sears or other qualified service center.
1 | Worn, bent | or loose blade | I | Replace blade Tighten blade bolt |
2 | Bent blade | mandrel | 2 | Contact a Sears or other |
qualified service center
|
|
| 3 | Looseldamaged part(s) | |
Engine | continues | to | Faulty | ||
run when operator |
| control | system | ||
|
|
| |||
leaves | seat | with |
|
|
|
attachment | clutch |
|
|
| |
engaged |
|
|
|
|
|
3Tighten loose part(s). Replace damaged parts.
1Check wiring, switches and connections. If not corrected, contact a Sears or other
29