Craftsman 358.35161 manual Loosen, Justment, Chain Adjustment

Page 19

2.Loosenandremovebarknobcom- pletelybyliftingteverandturning counterclockwise,

CRRF

LOOSEN

3.Loosen chain tension by turning

adjusting wheel (upward direction),

Remove clutch cover.

\

Bar

Knob

Drive Links

7.Place chain over and behind clutch

retainer, fitting the drive links in the clutch drum sprocket.

8.Fit bottom of drive links between the teeth in the sprocket in the nose of the guide bar.

9.Fit chain drive links into bar groove.

10.Putt guide bar forward until chain is snug in guide bar groove. Ensure all drive links are in the bar groove.

11.install clutch coven Be sure adjust- ing pin is in the adjusting pin hole

in the guide bar,

CAUTION: tt is very important when installing the clutch cover that the adjust- ing pin aligns into the adjusting pin hole in the bar. Failure to install the clutch cover correctly may result in permanent damage to your chain saw.

view of clutch

cove[

4.Slide guide bar on bar bolts until guide bar stops against clutch drum sprocket.

Guide bar

Bar bolts

5.Remove the old chain.

6.Carefully remove the chain from the package. Hold chain with the drive links as shown.

DHRECTtONOF ROTATION

B_ck

Adjusting

12.install bar knob and finger tighten only. Do not tighten any further at this point. Proceed to CHAIN AD-

JUSTMENT.

CHAIN ADJUSTMENT

See CHECK CHAIN TENSION in MAINTE- NANCE section.

CARBURETOR ADJUSTMENT

,_. WARNING: The chain wilt be

moving during most of this procedure. Wear your protective equipment and observe all safety precautions. The chain must not move at idle speed. The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the fol- lowing conditions:

•Chain moves at idle. See IDLE SPEED-T adjusting procedure.

•Saw witt not idle. See iDLE SPEED-T adjusting procedure.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Operators Manual Plan Ahead ONE Year Full Warranty on Craftsman GAS Chain SAWGuard Against Kickback Carburetor AdjustmentMaintain Your SAW in Good Working Order Handle Fuel with CautionAvoid Pinch-Kickback Reduce the Chance KickbackAvoid Putl-ln WE do not REP Chain BrakeAssembly Carton ContentsModel Chain Tension ON/STOP SwitchCHOKE/FAST Idle Lever Primer BulbStarting Position Guide BAR and Chain OILFueling Engine Stopping Your EngineDifficult Starting or 8tatting a flooded engine Starting a Warm EngineInertia activating function control Braking function controlOperating Tips Hinge holds tree on stump and helps control fall Tree Felling TechniquesFelling Large Trees Notch CUT and Felling the TreeTypes of Cutting Used for Bucking Bucking Using a LOG or Support StandCutting a Fallen Tree Bucking Important PointsPruning Using a support standLimbing and Pruning Iiwarning LimbingResponsibilities Check Chain Sharpness Hand tighten onlytCheck Guide BAR Check Fuel Mixture Level Clean AIR FilterInspect and Clean Unit and Decals Check Chain BrakeTool8 required To Replace Chain Chain ReplacementLoosen Chain AdjustmentJustment Other Seasonal StorageFuel System EngineTrouble Cause Troubleshooting TableRemedy Remedy TroubleWhat is Covered Repair or Your Warranty RightsOff-road engine is purchased. Length of Coverage This war MAINTENANCE, Replacement and Repair Repair Parts Sears CHAtNSAW Model

358.35161 specifications

The Craftsman 358.35161 is a reliable and powerful gas-powered string trimmer designed for homeowners and landscaping enthusiasts alike. Known for its robust performance, this trimmer offers a blend of innovation, comfort, and efficiency.

One of the standout features of the Craftsman 358.35161 is its 25cc 2-cycle engine. This engine provides ample power to tackle tough weeds, grasses, and overgrowth while delivering a user-friendly experience. The lightweight design of this trimmer, weighing approximately 10 pounds, also enhances its maneuverability, allowing users to navigate around gardens, flower beds, and landscaping projects with ease.

The Craftsman 358.35161 incorporates a straight shaft design, which is particularly advantageous for reaching under shrubs and in tight spaces. This design not only promotes better balance and control but also allows for greater reach, making it easier to access hard-to-reach areas. The 17-inch cutting swath ensures that users can cover a significant area in a single pass, improving efficiency during use.

Comfort is a priority with the Craftsman 358.35161, as evidenced by its cushioned grip handle and adjustable shaft length. These features combine to reduce operator fatigue during extended use, allowing users to work for longer periods without discomfort.

The trimmer is equipped with a dual line, bump-feed cutting system, which makes it easy to advance the line without stopping the engine. This system also allows for quick line replacement, enabling users to get back to work with minimal downtime. The 0.095-inch line thickness ensures effective cutting power while also being durable enough to withstand regular use.

A notable technological feature of the Craftsman 358.35161 is its Easy Start System, designed to simplify the starting process. This system reduces the amount of effort needed to start the engine, allowing for a smoother, quicker ignition every time. The fuel-efficient engine also contributes to fewer emissions, making it a more environmentally friendly choice compared to older models.

In summary, the Craftsman 358.35161 is an excellent choice for anyone looking for a versatile and efficient string trimmer. With its lightweight design, powerful engine, user-friendly features, and innovative technologies, it stands out as a reliable tool for maintaining beautiful landscapes. Whether you’re tackling simple yard maintenance or more demanding landscaping tasks, the Craftsman 358.35161 proves itself to be a valuable ally in your gardening endeavors.
Top Page Image Contents