New Media Technology Omnia ONE Multicast manual Output

Page 43

Configures the DSP processing chain to swap the Left and Right internal channels, that is, the DSP Left Channel is fed from Right Channel input and the DSP Right Channel is fed from the Left Channel input. Note that this selection is active in all sources selected as Primary and Secondary (Failover) audio sources.

<-Exit

Click on this option to return to the Input/Output submenu.

Output

There are five controls under the heading “Output” and each will be explained in the order in which they appear in the menu:

<-Exit

Click on this option to return to the Input/Output submenu

Anlg Level (Analog Level)

Adjusts the master audio Output level for the analog outputs which appear on the rear panel XLR male connectors. This control adjusts both the left and right stereo channel simultaneously.

Right Trim

Allows a +/-3dB adjustment of the right analog audio channel gain to correct minor left/right balance problems in equipment following the OmniaONE. The left channel output gain is not affected by this control and is set using the master Analog Level control previously described.

AES Level (AES/EBU Level)

Adjusts the master audio Output level for the AES Digital Output which appears on the rear panel RJ-45 StudioHUBconnector.

Right Trim

Allows a +/-3dB adjustment of the right digital audio channel gain to correct minor left/right balance problems in equipment following the OmniaONE. The left channel output gain is not affected by this control and is set using the master AES Level control previously described.

Samp. Rate (Sample Rate)

Configures the Output Sample Rate. Options are as follows:

[48k]

Slaves the output sample rate to the Omnia’s internal 48kHz sample clock. To use output sample rates other than 48 kHz, Input or External sync must be used.

[Input]

Slaves the output sample rate to the sample rate present on the Omnia’s AES

digital input. Synchronization is possible over a range of sample rates from 32kHz to 96kHz.

[Ext] (External)

OmniaONE Multicast - Use and Operation Manual – Version 0.90

43

Image 43
Contents Omnia 2101 Superior Avenue Cleveland, Ohio 44114 USA Installation and Operation Manual Version 0.9i / MarchOmnia ONE Multicast Audio Processor withOmniaONE Multicast - Use and Operation Manual - Version January Welcome to Omnia.ONEOmniaONE Multicast - Use and Operation Manual - Version Jog Wheel OmniaONE Quick-Start SetupHeadphone Jack Headphone Level ControlTable Of Contents Processing PresetAdministrative Chapter-4 Main Menu SelectionsAppendix A Performance Specifications Multicast Sensus→ Technology Audio Processingx3Overview Codec ProvisioningOmniaONE Multicast and HD→ Radio The Omnia Development Team So… what’s so smart about Sensus→?Important Note SincerelyS A F E T Y I N S T R U C T I O N S The Exclamation Point HAZARD / WARNING LABELSThe Lightning Flash With with the EU RoHS Directive Manual Update Notification About This Manual Chapter-1 InstallationPre-Installation Tasks AC Power EnvironmentOmniaONE utilizes an un-switched EMI-filtered IEC power-entry module Installation & ConnectionsRear Panel Connections A Note About Relative PhaseAnalog Audio Inputs and Outputs Ethernet 10BaseT/100BaseT Remote and Livewire I/O Ethernet ConnectionRS-232 Modem Port RS-232 Modem Connection DB-9FDB-9M GPI “Interface” Connector Powering UpGeneral Purpose Interface GPI DB-9M Level Meters & Processing Bargraphs Chapter-2 Getting To Know Your OmniaONEThe OmniaONE User Interface Headphone Level ControlProcessing Meter Display Audio I/O Level DisplayAudio I/O Level Display Using the Jog Wheel Preset Processing Input/Output Administrative Main MenuThe OmniaONE Main Menu offers five selections Proper Setting of Input Levels A Word About Density, Clarity, and Intelligibility Chapter-3 Getting The Sound You WantQuality Versus Density Increasing Density/Loudness Equalization EQ Changes Adding More Detail-When Loudness Isn’t The Last Word3. Increase the Release setting in the Low Frequency Limiter Thunder Bass2. Increase the Drive to Low Frequency Limiter Chapter-4 Main Menu Selections PresetProcessing Delete Preset Save PresetPre-processing Rename PresetAdjust Processing ExitEnhancers Mid Drive Xover CrossoverLow Band AGC Low DriveLow Band Limiter Mid Band AGCPres Band AGC Presence Band AGC High Band AGCMixer Mid Band LimiterPresence Band Limiter High Band LimiterSen Level Sensus→ Level Sensus→Hi Band Sen Freq Sensus→ FrequencyIMPORTANT NOTE Final LimitInput/Output Input Mtr Select Meter SelectInvert Output Bypass Save IO ConfigRename IO Config AdministrativeLoad IO Config Delete IO ConfigContrast Network ConfigurationReboot AboutLock Front Panel OmniaONE Multicast - Use and Operation Manual - Version OmniaONE Multicast Appendix A Performance SpecificationsGPI Interface Configuration Four fully optoisolated inputs Shipping Weight 10 lbs. / 4.54 kg OmniaONE Multicast - Use and Operation Manual - Version Diagnostic and Error Messages Appendix B Troubleshooting/Service/WarrantyElectrical and mechanical safety note 3. Unit will not boot Narrowing down problemsVia Phone & Mail USA and non-European Countries Obtaining ServiceVia the World Wide Web Via E-MailWarranty OmniaONE Multicast - Use and Operation Manual - Version Trigger Scripts Appendix C Remote Control & Software Update ProcedureRemote Control Software Update Procedure7. Click the Status Page link Return to Configuration. Reboot Processor