Sears 831.105021 SPA Shell Diagram SPA Operation, Six uni-directional thera-jets, Suction vent

Page 11

SPA SHELL DIAGRAM

C

A

E

A

B

SPA OPERATION

Refer to the diagram above. The function of each component is explained below:

The

six uni-directional thera-jets

(A) are located on

the sides of the spa. Five jets focus a water massage

 

on your upper or lower back. The remaining jet pro-

 

vides a foot hydro-massage when you are in the

 

reclining seat.

 

The

three multi-directional thera-jets

(B) can be

adjusted for a custom hydro-massage. One of the jets is located on the reclining seat and focuses the water massage on your lower back. Another jet is located on one of the bench seats, below a uni-directional thera-jet, and focuses a water massage on your lower or middle back. The remaining jet, located on the other bench seat, focuses a water massage on your upper or lower back.

Note: Each thera-jet can be shut off by being pressed in and turned back on by being pulled out.

G

A

B

F

D

A

B

The filter (C) can be removed for cleaning and replacement (see page 17).

The

suction vent

(D), located near the floor of the

spa, brings the water into the pump, in order to oper-

 

ate the system. The suction cover should always be in

 

place over the suction vent.

 

Never operate the spa

without the suction cover in place.

 

 

This spa is ozone ready. An optional ozone generator

 

can be installed to utilize the

ozone jet

(E). Ozone

provides a way to help sanitize your spa with minimal

 

chemical treatment.

 

 

 

The temperature probe (F) reads the current water temperature, which is displayed on the console.

The spa also has a light (G) for evening use.

The spa features automatic freeze protection. If the

water temperature falls below 40°F (4°C), the pump will begin circulating and heating the water to prevent the water from freezing.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents 800 Model No Serial NoTable of Contents Important Do not allow the hydrotherapy Important Safety InstructionsSPA Use the hydrotherapy spa only as described This manualMust always be open Up the hydrotherapy spa within five feetMinimum No AWG 13.3 mm Uct Privacy of your own home Fully before using the RenewConsole Spa Shell Light Spa Cover Access Filter Before YOU BeginChoosing a Location for the Hydrotherapy SPA If you set up the hydrotherapy spa insideIf you set up the hydrotherapy spa outside Assembly Requires the Following SET-UP and AssemblySpa to be used before the warning sign is posted Do not overfillSpa Starting the Hydrotherapy SPA Testing and Treating the WaterPlugging in the Hydrotherapy SPA Ozone jet SPA Shell Diagram SPA OperationSix uni-directional thera-jets Suction ventCord must be unplugged Light Button Console DiagramOr heating the water as needed Attaching the RED and Blue Light Covers Posting the Warning SignSecuring the SPA Cover Maintenance Maintaining the Proper PH Balance Access Panel ScrewsNever mix different chemicals Always store chemicals in a cool, dry placeOpening and Closing the CUT-OFF Valves Draining the Hydrotherapy SPAHydrotherapy spa should always be covered Winter USE and Care Converting the SPA to a 240 Volt Power SourceChecking and Cleaning the Filter Adjusting the Filter DiverterTrouble -SHOOTING Symptom the SPA will not OperateSymptom the Pump Hums Symptom the Water does not HeatSome water loss due to evaporation is normal Symptom the Water Level DropsKey No. Qty Description Part LIST-Model NoExploded DRAWING-Model No Page Page Part No R1200A Ordering Replacement PartsLimited Five Year Massage SPA Warranty Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT
Top Page Image Contents