Sears 831.105021 user manual SET-UP and Assembly, Assembly Requires the Following

Page 8

SET-UP AND ASSEMBLY

Before beginning assembly, carefully read the following information and instructions:

•Place all parts in a cleared area and remove the packing materials from the spa shell; do not dis- pose of the packing materials until assembly is completed and the spa is in operation.

•Assembly requires two people.

•Note: Some small parts may have been pre- attached for shipping. If a part is not in the parts bag, check to see if it has been pre-attached.

•During assembly, make sure that all parts are ori- ented as shown in the drawings.

•Read each assembly step before you begin.

•Tighten all parts as you assemble them, unless instructed to do otherwise.

ASSEMBLY REQUIRES THE FOLLOWING

TOOLS (not included):

• One (1) phillips screwdriver

1.Before beginning assembly, make sure that you have read and understand the information on

the previous two pages.

Remove the four screws from the access cover

on

the console side of the spa. Remove the access

cover by sliding it down and then pulling

the bottom

of it away from the spa.

Be careful not to damage

the spa shell.

 

 

Remove the Power Cord with the GFCI from inside the spa.

2.Locate and check the positions of the two cut-off valves. The cut-off valves may have been closed at the factory during manufacturing. However, the cut- off valves must be open for spa operation. To open the valves, hold the handles and turn them until you

can pull them out to the open position.

IMPORTANT:

THE MOTOR WILL BE DAMAGED IF IT IS OPER-

 

ATED WITH THE CUT-OFF VALVES CLOSED.

 

Close the valve knob on the drain hose. Thread the cap onto the drain hose. Thread the drain plug into the Pump Motor (13). Tighten the two pump fittings.

1

 

 

 

 

 

 

Access

 

 

 

Cover

 

 

 

Screws

 

 

 

Power Cord

2

 

 

 

 

Cut-off

 

Cut-off

 

Valve

 

 

 

 

Valve

 

 

 

13

 

 

 

Drain Hose

 

Valve

Drain

Pump

Cap

Plug

Fittings

 

Knob

 

 

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Model No Serial No 800Table of Contents Important Safety Instructions SPAUse the hydrotherapy spa only as described This manual Important Do not allow the hydrotherapyMust always be open Up the hydrotherapy spa within five feetMinimum No AWG 13.3 mm Uct Fully before using the Renew Console Spa Shell Light Spa Cover Access FilterBefore YOU Begin Privacy of your own homeChoosing a Location for the Hydrotherapy SPA If you set up the hydrotherapy spa insideIf you set up the hydrotherapy spa outside SET-UP and Assembly Assembly Requires the FollowingSpa to be used before the warning sign is posted Do not overfillSpa Starting the Hydrotherapy SPA Testing and Treating the WaterPlugging in the Hydrotherapy SPA SPA Shell Diagram SPA Operation Six uni-directional thera-jetsSuction vent Ozone jetCord must be unplugged Light Button Console DiagramOr heating the water as needed Attaching the RED and Blue Light Covers Posting the Warning SignSecuring the SPA Cover Maintenance Access Panel Screws Never mix different chemicalsAlways store chemicals in a cool, dry place Maintaining the Proper PH BalanceOpening and Closing the CUT-OFF Valves Draining the Hydrotherapy SPAHydrotherapy spa should always be covered Converting the SPA to a 240 Volt Power Source Checking and Cleaning the FilterAdjusting the Filter Diverter Winter USE and CareSymptom the SPA will not Operate Symptom the Pump HumsSymptom the Water does not Heat Trouble -SHOOTINGSymptom the Water Level Drops Some water loss due to evaporation is normalPart LIST-Model No Key No. Qty DescriptionExploded DRAWING-Model No Page Page Ordering Replacement Parts Limited Five Year Massage SPA WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT Part No R1200A
Top Page Image Contents