Sears 917.257632 Operation, Before Starting the Engine, To Operate on Hills, To Transport

Page 12

OPERATION

TO OPERATE MOWER (See Fig. 8)

Your tractor is equipped with an operator presence sensing switch_ Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

=Select desired height of cut.

°Start mower blades by engaging attachment clutch control.

*TO STOP MOWER BLADES - disengage attachment clutch control

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the dis- charge guard in place.

 

ill

 

ATTACHMENT

CLUTCH LEVER

ATTACHMENT

"DISENGAGED"

POSITION

 

"ENGAGED"

LIFT LEVER

 

HIGH POSITION

 

POSITION

TO OPERATE ON HILLS

CAUTION: Do not drive up or down ! hills with slopes greater than 15 ° and I do not dr!ve across anY slope.

•Choose the slowest speed before starting up or'down hills°

•Avoid stopping or changing speed on hills.

°If slowing is necessary, move throttle control lever to slower position°

°If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

•Move gearshift lever to 1st gear. Be sure you have allowed room for'tractor to roll slightly as you restart movement.

°To restart movement, slowly release parking brake and clutch/brake pedal

°Make all turns slowly.

TO TRANSPORT

•Raise attachment lift to highest position with attach- ment lift control.

•When pushing or towing yourtractor, be sure gearshift lever is in neutral (N) position.

•Do not push or tow tractor at more than five (5) MPH.

NOTE: To protect hood from damage when transporting your tractor on a truckor a trailer, be sure hood is closed and secured totractor. Usean appropriate means of tying hood to tractor (rope, cord, etc.)..

 

BEFORE STARTING THE ENGINE

 

CHECK ENGINE OIL LEVEL (See Fig. 14)

 

• The engine in your tractor has been shipped, from the

 

factory, already filled with summer weight oil.

 

• Check engine oil with tractor on level ground.

DISCHARGE

• Remove oil fitlcap/dipstick and wipe clean, reinsert the

dipstick and screw cap tight, wait for'a few seconds,

GUARD

remove and read oil level, if necessary, add oil until

 

FIG. 8

"FULL" mark on dipstick is reached.. Do not overfill.

• For cold weather operation you should change oil for easier starting (See "OIL VISCOSITY CHART" in the Customer Responsibilities section of this manual).

• To change engine oil, see the Customer Responsibili- ties section in this manual.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents IIIIIIIIIIIIIIIIIIIIIIrrmlllllllllll Safe Operation Practices for Ride-On Mowers ChildrenMaintenance Agreement ModelTable of Contents Engin E Maintenance PerformanceParts bag contents not shown full size Hardware PackAssembly Tools Required for AssemblyTo Removetractor from Carton Unpack CartonHOW to SET UP ,/OURTRACTOR Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsChecklist Install Battery See FigsOperation HOW to USE Your Tractor To Adjust Mower Cutting Height See FigTo USE Throttle Control See Fig Stopping See FigOperation Before Starting the EngineTo Operate on Hills To TransportADD Gasoline To Start Engine See FigLubrication Chart Customer ResponsibilitiesGeneral Recommendations CheckTransaxle CoolingBattery See Fig Blade Removal See FigTo Sharpen Blade See Fig TiresCustomer R SibilitiesEngine Transaxle CoolingClean AIR Screen See Fig MufflerSpark Plugs Engine Cooling Fins See FigService and Adjustments To Install Mower See FigTo Remove Mower See Fig Mowerwill be easier to remove from the right side oftractorTo Level Mower Housing Bothfront Links Must be Equal in LengthTo Adjust Brake See Fig To Replace Mower Blade Drive BeltTo Replace Motion Drive Belt See Fig STATONARY!1 TransaxleTo Adjust Steering Wheel Alignment To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Remove Wheel for RepairsTo Remove Hood and Grill Assembly See Fig SE and aTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Throttle Control Cable To Adjust Carburetor See FigPreliminary Setting Final SettingBattery StorageTractor Fuel SystemProblemcause CorrectionProblem PointsCorrection Wiring Insulated Clips SolenoidWith a Special Alternator Will Change with EngineElectrical Battery 12 Volt 25 AMP KEY Part DescriptionBolt Hex Hd 1/4-20unc X 3/4 Tube PasticChassis and Enclosures Part Description 105037XDrive KEY Part NO. noDescripon KEY Part Steering Assembly 13 HP 42 Tractor --MODEL Number Seat Assembly 127437145006 Decals Wheels & TiresOptional Equipment Engine24 fJ Repair Parts 161718 O 13 HP 42 TRACTOR- Model Number KEY Part NO. NO. DescriptionMower Retainer 13 HP 42 Tractor - Model Dana Transaxle Model Number2732 3635 KEY Part NO. no Description Jaw, Brake761 306 562308 305 337108 618 634 Briggs & Stratton Engine Model Number 28M707, Type Number222 240 356 877305 668 1044 455311 842Carburetor Overhaul KIT Gasket SET Carburetor Gasket SETBriggs & Stratton Engine Model Number 28M707, Type Number KEY Part NO. NO+ Description NO. no Page SERVmCE Notes Page Only Ride UP and Down Hill Not Across Hill Sight and Hold this Level with SKY Line or TreeIf YOU Need Repair Service or Parts For Repair SERVICE, Call this Toll Free NumberPart Number Part Description

917.257632 specifications

The Sears 917.257632 is a versatile lawn tractor that has been designed to cater to homeowners looking for efficiency and ease in lawn care. This model stands out with its blend of features that make it an attractive option for anyone looking to maintain a well-manicured yard.

One of the main features of the Sears 917.257632 is its powerful engine. It is equipped with a reliable 19 horsepower engine, providing ample power to handle various tasks throughout the yard. Whether mowing the lawn, hauling materials, or towing attachments, this lawn tractor ensures consistent performance.

The tractor boasts a wide cutting deck, typically measuring around 42 inches, which allows for a broader mowing path and reduces the time spent cutting the grass. The cutting height is easily adjustable, giving users the flexibility to choose their preferred grass length, ensuring a professional-looking finish every time.

The 917.257632 features a hydrostatic transmission, offering smooth and seamless speed adjustments without the need for gear shifting. This technology enhances ease of use, allowing operators to focus on navigating the lawn rather than managing gears. The intuitive foot pedal provides effortless control, making it easier to maneuver around obstacles.

Comfort is another significant aspect of the Sears 917.257632. The tractor comes with a cushioned seat that offers ample support during longer mowing sessions, ensuring an enjoyable experience. The ergonomic steering wheel is designed for optimal handling and ease of navigation, allowing users to operate the lawn tractor with minimal fatigue.

Additionally, the Sears 917.257632 includes ample storage options, with a compartment located near the operator’s seat to store essential tools and supplies. The tractor is designed with durability in mind, featuring robust materials that withstand regular use and varied weather conditions.

Safety features are critical in this model, with mechanisms such as a blade brake that automatically stops the blades when the operator leaves the seat. This ensures peace of mind while operating the machine, particularly on uneven terrain.

In summary, the Sears 917.257632 is a well-rounded lawn tractor that combines power, comfort, and advanced technology, making it an excellent choice for homeowners seeking a reliable solution for their lawn care needs. Its diverse features and user-friendly design enhance the overall mowing experience, setting it apart in the competitive market of lawn tractors.
Top Page Image Contents