Sears 917.257632 owner manual To Level Mower Housing, Bothfront Links Must be Equal in Length

Page 19

$ERVmCE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on levetground or driveway. Make sure tires are properly inflated (See "PRODUCT SPEC IFICAT!ONS" on page 3 of this manual). Iftires are over or underinflated, you will not properly adjust your mower_

SIDE-TO-SIDE ADJUSTMENT (See Figs. 19 and 20)

. Raise mower to its highest position.

oAt the midpoint of both sides of mower, measure height from bottom edge of mowerto ground. Distance A on both sides of mower should be the same or within 1/4" of each other.

oIf adjustment is necessary, make adjustment on one side of mower only.,

°To raise one side of mower, tighten lift link adjustment nut on that side_

QTo !ower one side of mower, loosen lift link adjustment nut on that side_

NOTE: Each full turn of adjustment nut will change mower height about 1/8'L

•Recheck measurements after adjusting.

BOTTOM EDGE

BOTTOM EDGE

OF MOWER TO

OF MOWER TO

GROUND

GROUND

GROUND LINE

FIG. 19

SUSPENSION

ARM

LIFT LtNK

ADJUSTMENT NUT

FIG. 20

FRONT_TO-BACK ADJUSTMENT (See Figs,. 21 and 22)

IMPORTANT: DECK MUST BE LEVEL SiDE-TO-SIDE. IF

THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS

NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE*TO-

SIDE..

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/4" to 3/4" lower than the rear when the mower is in its highest position°

Check adjustment on right side of tractor° Measure dis- tance "D" directly in front and behind the mand ret at bottom edge of mower housing as shown_

°Before making any necessary adjustments, check that both front links are equal in length, Both linksshould be approximately 10-3/8",,

°If links are not equal in length, adjust one linkto same length as other link,,

=To lower front of mower loosen nut "E" on both front links an equal number of turns.,

°When distance "D" is 1/4" to 3/4" lower at front than

rear, tighten nuts "F" against trunnion on both front links.

°To raise front of mower, loosen nut"F" from trunnion on both front links. Tighten nut "E" on both front links an equal number of turns,

. When distance "D" is 1/4" to 3/4" lower at front than rear, tighten nut"F" against trunnion on both front links°

°Recheck side-to-side adjustment.

MANDREL

FIG. 21

BOTHFRONT LINKS MUST BE EQUAL IN LENGTH

NUT "E"

NUT"I

FRONT LINKS

TRUNNION

19

FIG. 22

 

Page 18 Page 20
Image 19
Page 18 Page 20
Contents IIIIIIIIIIIIIIIIIIIIIIrrmlllllllllll Children Safe Operation Practices for Ride-On MowersModel Maintenance AgreementTable of Contents Performance Engin E MaintenanceHardware Pack Parts bag contents not shown full sizeUnpack Carton AssemblyTools Required for Assembly To Removetractor from CartonCheck for Proper Position of ALL Belts HOW to SET UP ,/OURTRACTORCheck Tire Pressure Check Deck LevelnessInstall Battery See Figs ChecklistOperation Stopping See Fig HOW to USE Your TractorTo Adjust Mower Cutting Height See Fig To USE Throttle Control See FigTo Transport OperationBefore Starting the Engine To Operate on HillsTo Start Engine See Fig ADD GasolineCheckTransaxle Cooling Lubrication ChartCustomer Responsibilities General RecommendationsTires Battery See FigBlade Removal See Fig To Sharpen Blade See FigTransaxle Cooling Customer RSibilities EngineEngine Cooling Fins See Fig Clean AIR Screen See FigMuffler Spark PlugsMowerwill be easier to remove from the right side oftractor Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigBothfront Links Must be Equal in Length To Level Mower HousingSTATONARY!1 Transaxle To Adjust Brake See FigTo Replace Mower Blade Drive Belt To Replace Motion Drive Belt See FigTo Remove Wheel for Repairs To Adjust Steering Wheel AlignmentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERInterlocks and Relays To Remove Hood and Grill Assembly See FigSE and a To Replace Headlight BulbFinal Setting To Adjust Throttle Control CableTo Adjust Carburetor See Fig Preliminary SettingFuel System BatteryStorage TractorCorrection ProblemcausePoints ProblemCorrection Will Change with Engine Wiring Insulated ClipsSolenoid With a Special AlternatorElectrical Tube Pastic Battery 12 Volt 25 AMPKEY Part Description Bolt Hex Hd 1/4-20unc X 3/4Chassis and Enclosures 105037X Part DescriptionDrive NO. no KEY PartDescripon KEY Part Steering Assembly 13 HP 42 Tractor --MODEL Number 127437 Seat Assembly145006 Wheels & Tires DecalsEngine Optional Equipment24 fJ Repair Parts 161718 O KEY Part NO. NO. Description 13 HP 42 TRACTOR- Model NumberMower Retainer Dana Transaxle Model Number 13 HP 42 Tractor - Model2732 3635 Jaw, Brake KEY Part NO. no Description337 761306 562 308 305Briggs & Stratton Engine Model Number 28M707, Type Number 108 618 634455 222 240356 877 305 668 1044Gasket SET Carburetor Gasket SET 311842 Carburetor Overhaul KITBriggs & Stratton Engine Model Number 28M707, Type Number KEY Part NO. NO+ Description NO. no Page SERVmCE Notes Page Sight and Hold this Level with SKY Line or Tree Only Ride UP and Down Hill Not Across HillFor Repair SERVICE, Call this Toll Free Number If YOU Need Repair Service or PartsPart Number Part Description

917.257632 specifications

The Sears 917.257632 is a versatile lawn tractor that has been designed to cater to homeowners looking for efficiency and ease in lawn care. This model stands out with its blend of features that make it an attractive option for anyone looking to maintain a well-manicured yard.

One of the main features of the Sears 917.257632 is its powerful engine. It is equipped with a reliable 19 horsepower engine, providing ample power to handle various tasks throughout the yard. Whether mowing the lawn, hauling materials, or towing attachments, this lawn tractor ensures consistent performance.

The tractor boasts a wide cutting deck, typically measuring around 42 inches, which allows for a broader mowing path and reduces the time spent cutting the grass. The cutting height is easily adjustable, giving users the flexibility to choose their preferred grass length, ensuring a professional-looking finish every time.

The 917.257632 features a hydrostatic transmission, offering smooth and seamless speed adjustments without the need for gear shifting. This technology enhances ease of use, allowing operators to focus on navigating the lawn rather than managing gears. The intuitive foot pedal provides effortless control, making it easier to maneuver around obstacles.

Comfort is another significant aspect of the Sears 917.257632. The tractor comes with a cushioned seat that offers ample support during longer mowing sessions, ensuring an enjoyable experience. The ergonomic steering wheel is designed for optimal handling and ease of navigation, allowing users to operate the lawn tractor with minimal fatigue.

Additionally, the Sears 917.257632 includes ample storage options, with a compartment located near the operator’s seat to store essential tools and supplies. The tractor is designed with durability in mind, featuring robust materials that withstand regular use and varied weather conditions.

Safety features are critical in this model, with mechanisms such as a blade brake that automatically stops the blades when the operator leaves the seat. This ensures peace of mind while operating the machine, particularly on uneven terrain.

In summary, the Sears 917.257632 is a well-rounded lawn tractor that combines power, comfort, and advanced technology, making it an excellent choice for homeowners seeking a reliable solution for their lawn care needs. Its diverse features and user-friendly design enhance the overall mowing experience, setting it apart in the competitive market of lawn tractors.
Top Page Image Contents