Sears 917.257632 Tools Required for Assembly, To Removetractor from Carton, Unpack Carton

Page 7

ASSEMBLY

_...............,

. iUillLiiJl

i,,_,-- -

,

. ...,

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes, To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)

5/16" wrench

(1) 3/4" wrench

(2)

7/16" wrenches

Tire pressure gauge

(1)

1/2" wrench

Utility knife

(!)

9/t6" wrench

 

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steedng wheel)°

TO REMOVETRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton (See page 6).

,Cut, from top to bottom, along lineson all four corners of carton, and lay panels flaL

•Check for any additional loose parts or cartons and remove_

BEFORE ROLLINGTRACTOR OFF SKID

ATTACH STEERING WHEEL (See Fig. 1)

-Slide the steering bushing over the steering shaft,,

°Raise steering shaft forward until screw holes in dash line up with steering bushing. Install two (2) sheet metal screws and tighten securely.

°Position steering boot over steering shaft.

°Place tabs of steering boot over tab slots in dash and push down to secure.

=Slide steedng wheel adapter onto upper steering shaft.

•Position front wheels of the tractor so they are pointing straight forward,

,Position steering wheel so cross bars are horizontal (left to right) andslide onto adapter°

oAssemble large flat washer and 3/8-24 Iocknut and tighten securely.

°Snap steering wheel insert into center of steering whee!°

°Remove protective plasticfrom tractor hood and grill.

IMPORTANT:CHECK FOR AND REMOVE ANY STAPLES

IN SKiDTHAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKIDo

STEERING WHEEL INSERT

!8-.24 LOCKNUT

_

LARGE FLAT WASHER

STEERING

 

SHEET

WHEEL

 

METAL

ADAPTER--S,

TABS

SCREW

STEERING

/_

 

(ASSEMBLY

 

 

POSITION)

 

 

 

 

SLOT

STEERING SHAFT

(SHIPPING POSITION)

FIG. 1

TO ROLL TRACTOR OFF SKID (See Fig. 6)

•Raise attachment lift lever to its highest position.

°Release parking brake by depressing clutch/brake pedal.

oPlace gearshift lever in neutral (N) position,

• Roll tractor backwards off skid,

•Remove banding holding discharge guard up against tractor.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents IIIIIIIIIIIIIIIIIIIIIIrrmlllllllllll Children Safe Operation Practices for Ride-On MowersModel Maintenance AgreementTable of Contents Performance Engin E MaintenanceHardware Pack Parts bag contents not shown full sizeUnpack Carton AssemblyTools Required for Assembly To Removetractor from CartonCheck for Proper Position of ALL Belts HOW to SET UP ,/OURTRACTORCheck Tire Pressure Check Deck LevelnessInstall Battery See Figs ChecklistOperation Stopping See Fig HOW to USE Your TractorTo Adjust Mower Cutting Height See Fig To USE Throttle Control See FigTo Transport OperationBefore Starting the Engine To Operate on HillsTo Start Engine See Fig ADD GasolineCheckTransaxle Cooling Lubrication ChartCustomer Responsibilities General RecommendationsTires Battery See FigBlade Removal See Fig To Sharpen Blade See FigTransaxle Cooling Customer RSibilities EngineEngine Cooling Fins See Fig Clean AIR Screen See FigMuffler Spark PlugsMowerwill be easier to remove from the right side oftractor Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigBothfront Links Must be Equal in Length To Level Mower HousingSTATONARY!1 Transaxle To Adjust Brake See FigTo Replace Mower Blade Drive Belt To Replace Motion Drive Belt See FigTo Remove Wheel for Repairs To Adjust Steering Wheel AlignmentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERInterlocks and Relays To Remove Hood and Grill Assembly See FigSE and a To Replace Headlight BulbFinal Setting To Adjust Throttle Control CableTo Adjust Carburetor See Fig Preliminary SettingFuel System BatteryStorage TractorCorrection ProblemcausePoints ProblemCorrection Will Change with Engine Wiring Insulated ClipsSolenoid With a Special AlternatorElectrical Tube Pastic Battery 12 Volt 25 AMPKEY Part Description Bolt Hex Hd 1/4-20unc X 3/4Chassis and Enclosures 105037X Part DescriptionDrive NO. no KEY PartDescripon KEY Part Steering Assembly 13 HP 42 Tractor --MODEL Number 127437 Seat Assembly145006 Wheels & Tires DecalsEngine Optional Equipment24 fJ Repair Parts 161718 O KEY Part NO. NO. Description 13 HP 42 TRACTOR- Model NumberMower Retainer Dana Transaxle Model Number 13 HP 42 Tractor - Model2732 3635 Jaw, Brake KEY Part NO. no Description337 761306 562 308 305Briggs & Stratton Engine Model Number 28M707, Type Number 108 618 634455 222 240356 877 305 668 1044Gasket SET Carburetor Gasket SET 311842 Carburetor Overhaul KITBriggs & Stratton Engine Model Number 28M707, Type Number KEY Part NO. NO+ Description NO. no Page SERVmCE Notes Page Sight and Hold this Level with SKY Line or Tree Only Ride UP and Down Hill Not Across HillFor Repair SERVICE, Call this Toll Free Number If YOU Need Repair Service or PartsPart Number Part Description

917.257632 specifications

The Sears 917.257632 is a versatile lawn tractor that has been designed to cater to homeowners looking for efficiency and ease in lawn care. This model stands out with its blend of features that make it an attractive option for anyone looking to maintain a well-manicured yard.

One of the main features of the Sears 917.257632 is its powerful engine. It is equipped with a reliable 19 horsepower engine, providing ample power to handle various tasks throughout the yard. Whether mowing the lawn, hauling materials, or towing attachments, this lawn tractor ensures consistent performance.

The tractor boasts a wide cutting deck, typically measuring around 42 inches, which allows for a broader mowing path and reduces the time spent cutting the grass. The cutting height is easily adjustable, giving users the flexibility to choose their preferred grass length, ensuring a professional-looking finish every time.

The 917.257632 features a hydrostatic transmission, offering smooth and seamless speed adjustments without the need for gear shifting. This technology enhances ease of use, allowing operators to focus on navigating the lawn rather than managing gears. The intuitive foot pedal provides effortless control, making it easier to maneuver around obstacles.

Comfort is another significant aspect of the Sears 917.257632. The tractor comes with a cushioned seat that offers ample support during longer mowing sessions, ensuring an enjoyable experience. The ergonomic steering wheel is designed for optimal handling and ease of navigation, allowing users to operate the lawn tractor with minimal fatigue.

Additionally, the Sears 917.257632 includes ample storage options, with a compartment located near the operator’s seat to store essential tools and supplies. The tractor is designed with durability in mind, featuring robust materials that withstand regular use and varied weather conditions.

Safety features are critical in this model, with mechanisms such as a blade brake that automatically stops the blades when the operator leaves the seat. This ensures peace of mind while operating the machine, particularly on uneven terrain.

In summary, the Sears 917.257632 is a well-rounded lawn tractor that combines power, comfort, and advanced technology, making it an excellent choice for homeowners seeking a reliable solution for their lawn care needs. Its diverse features and user-friendly design enhance the overall mowing experience, setting it apart in the competitive market of lawn tractors.
Top Page Image Contents