McCulloch 532 43 41-98 Rev. 1 manual 02927

Page 35

5

02927

Turn the ignition key to “START position”.

NOTE!

Do not run the start motor more than 5 seconds at once. If the engine will not start, wait about 10 seconds before the next try.

Zündschlüssel auf “START” drehen.

HINWEIS!

Den Anlasser nicht jeweils länger als ca. 5 Sekunden betäti- gen. Wenn der Motor nicht anspringt, vor dem nächsten An- laßversuch ca. 10 Sekunden warten.

Let the ignition key return to the ”ON” position when the engine has started and push in the choke control as soon as the engine is running smoothly. Push the gas control to the required speed. For cutting: full gas.

Nach Anspringen des Motors den Zündschlüssel in die Stellung “ON” zurückgehen lassen. Den Kaltstarthebel zurückschieben, so daß der Motor gleichmäßig arbeitet. Den Gashebel auf die gewünschte Motordrehzahl stellen. Bei Mähen: Vollgas.

Amener la clé de contact sur la position "Démarrage" ("START").

REMARQUE!

Ne pas laisser tourner le démarreur plus de 5 secondes à chaque fois. Si le moteur ne démarre pas immédiatement, attendre une dizaine de secondes avant d'effectuer une nouvelle tentative.

Ponga la llave de encendido en la posición de arranque ”START”.

NOTA!

No haga funcionar el motor de arranque más de unos 5 segundos a la vez. Si el motor no arranca, espere unos 10 segundos antes de hacer otra tentativa.

Girare la chiave su “START”.

NOTA!

Non inserire il motorino di avviamento per più di 5 secondi per volta. Se il motore non parte attendere una decina di secondi prima di riprovare.

Draai de startsleutel naar “START”-positie

N.B.!

Laat de startmotor niet langer dan ca 5 sek. per keer draaien. Als de motor niet start, wacht dan ca 10 sek voordat u vol- gende poging doet.

Laisser ensuite la clé revenir sur sa position "On" lorsque le moteur a démarré et repousser la commande de starter dès que le moteur tourne régulièrement. Amener la commande des gaz à la position correspondante au régime moteur désiré. Pour la tonte, positionner cette manette dans l'encoche prévue pour obtenir le régime optimal pour la tonte (accélération maximale du moteur).

Dejar que la llave de encendido vuelva a la posición “ON” cuando ha arrancado el motor e introducir el estrangulador tan pronto como el motor funcione con regularidad. Ponga el acelerador en la posición deseada. Al cortar, a plenos gases.

Dopo l’avviamento, riportare la chiave su “ON”. Regolare il gas sul regime desiderato. Per il taglio: massimo regime “F”.

Draai de startsleutel terug in “ON”-posotie, wanneer de motor is gestart en schuif de choke in zordra de motor gelijkmatig loopt. Schuif de gashendel naar het gewenste toerental. Bij maaien: vol gas.

35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents M13597 Page III. Operation Safety RulesTraining II. PreparationIV. Maintenance and Storage III. Betrieb SicherheitsvorschriftenSchulung II. VorbereitungIV. Wartung UND Lagerung III. Utilisation Règles de SécuritéPrécautions D’UTILISATION II. PréparationIV. Entretien ET Entreposage III. Operación Reglas De SeguridadInstrucción II. PreparaciónIV. Mantenimiento Y Almacenamiento III. Funzionamento Norme AntinfortunisticheAddestramento ALL’USO II. PreparazioneIV. Manutenzione E Periodi DI INATTIVITA’ Maai alleen bij daglicht of goed kunstlicht VeiligheidsregelsII. Voorbereiding III. Bediening180 IV. Onderhoud EN Opslag06/6.01 Reverse 42%3!.,%45.ª,%3% $2%#46%ª&/2ª3!&%49 Gefahr ZU Vermeiden Schwefelsäure Augen Unver Augen Schützen Volante DE Dirección Volant DE DirectionSteering Wheel LenkradAsiento SeatSitz SiègeNota HinweisRemarque Install Battery Einbau DER Batterie 02604 Installatie mulcherplaat indien aanwezig Install Mulcher Plate if equippedMontage der Zerkleinerungsplatte falls installiert Anordnung der Bedienungseinrichtungen Positioning of controlsDe plaats van de bedieningsorganen Emplacement des commandesComandi Ubicación de los mandosAcceleratore Throttle controlGashebel AceleradorSchalthebel Commande de la boîte de vitessesPalanca de cambios Gear shift leverAcoplamiento y desacoplamiento del equipo de corte Commande dembrayage et de débrayage du carter de coupeConnection/disconnection of the cutting unit Ein und Ausschalten des MähaggregatsCerradura de encendido Ignition LockZündschloß Clé de contact et de démarrageKaltstartregler Parking brakeFeststellbremse Choke controlPlein de carburant Filling upReposición de combustible TankenLivello dell’olio Oil levelÖlstand Nivel de aceiteDriving . Betrieb . Conduite . Conducción . Guida . Rijden Page 02927 Conducción DrivingBetrieb ConduiteSistema de Funcionamiento Atrás ROS Reverse Operation System ROSRückwärtsgangsystem ROS Sécurité Marche Arrière ROSRatschläge zum Rasenmähen Sistema per operazioni in retromarcia ROSSysteem Voor Achteruit ROS Cutting tipsMaaitips Conseils pour la tonteConsejos para el corte Consigli per il taglio dell’erbaWaarschuwing WarnungAdvertencia Pericolo00272 Apagar el motor Switching off the engineAbschalten des Motors Extinction du moteurAdvertencia Cubierta del motor Engine hoodMotorhaube Capot moteurMantenimiento MaintenanceWartung EntretienÖlwechsel Durchführen Para Cambiar EL AceiteTo Change OIL PER Cambiare L’OLIOClean battery and terminals Check muffler Fill in dates as you complete regular service EveryCheck brake operation Clean air screen Clean engine cooling finsFiltre à air Sans filtre à huileVérification des freins Nettoyage de la grille daération Pré-filtrePulizia raffreddamento motore Vul telkens u service uitvoert, de datum Indien Om de Nodig50 ore Controllo freni Pulizia schermo ariaFahrer-Anwesenheitssystem und Rückwärts- gangsystem ROS Operator Presence System and Reverse Opera- tion System ROSControl Sistema Presencia Operador Lames BladesMesserbalken Messen CuchillasLame Desmontaje de la unidad de corte Dismantling of the cutting unitDemontage des Mähdecks Depose du Carter de CoupeMontaje de la unidad de corte Assembly of the cutting unitEinbau des Mähdecks Mise en place du carter de coupeSostituzione della cinghia di movimento lame Replacement of drive belt for cutting unitCambio de la correa propulsora del equipo de corte Auswechsein des Treibriemens für das Mähag- gregatAjuste de la unidad de corte Adjustment of the cutting unitEinstellung des Mähaggregats Réglage du carter de coupeReglage Transversal SIDE-TO-SIDE AdjustmentAdjuste DE Lado a Lado Seitliche EinstellungCambio de correa propulsora Replacement of drive beltRemplacement de la courroie dentraînement Auswechsein des TreibriemensEinstellung DES Schalthebels DES Differentialgetriebes Transaxle Gear Shift Lever Neutral AdjustmentPage Controlar el Freno To Check BrakeÜberprüfen der Bremse Pour vérifier le freinWASCHANLAGEN-ÖFFNUNG DER Abdeckung Deck Washout PortPort DE Lavage DU Châssis Boca DE Lavado DE LA PlataformaDekreinigingspoort Apertura DI Lavaggio DEL PiattoTroubleshooting . Störungssuche Recherche des pannes . Búsqueda de averías Ricerca guasti . Het localiseren van fouten Servicio ServiceStorage . Aufbewahrung . Remisage . Conservación Entretien et réparationsAl termine della stagione effettuare i seguenti interventi Rismessaggio . StallenServizio Page 07.02.10 JA

532 43 41-98 Rev. 1 specifications

The McCulloch 532 43 41-98 Rev. 1 is a robust and versatile lawn mower that showcases McCulloch's commitment to quality and innovation in outdoor power equipment. Designed for efficiency and ease of use, this model is well-suited for both residential and commercial applications.

One of the standout features of the McCulloch 532 43 41-98 Rev. 1 is its powerful engine. The mower is equipped with a reliable and durable engine that provides ample power to tackle various grass types and terrains. This engine ensures optimal performance while maintaining fuel efficiency, allowing users to cover larger areas without constant refueling.

The cutting deck of the McCulloch 532 43 41-98 Rev. 1 is ingeniously designed for superior grass cutting. It features a wide cutting width, which enables the user to mow larger areas more quickly. The adjustable cutting height mechanism allows for customizable grass length, accommodating different lawn types and personal preferences. This flexibility ensures a clean and professional-looking finish every time.

In terms of user comfort, the McCulloch 532 43 41-98 Rev. 1 is equipped with ergonomic handles designed to provide a comfortable grip during operation. These handles are adjustable, allowing users of varying heights to find their ideal mowing position. Additionally, the mower's lightweight design enhances maneuverability, making it easier to navigate around obstacles in the yard.

Safety is also a key consideration in the design of the McCulloch 532 43 41-98 Rev. 1. It includes essential safety features such as a blade brake that quickly stops the blades when the operator releases the handle. This feature minimizes the risk of accidents and enhances overall user confidence while mowing.

Another notable characteristic of the McCulloch 532 43 41-98 Rev. 1 is its ease of maintenance. The mower is designed for easy access to components making routine checks and servicing much simpler. This attention to detail ensures longevity and sustained performance over the years.

Overall, the McCulloch 532 43 41-98 Rev. 1 stands out as a reliable and efficient lawn mowing solution. With its powerful engine, adjustable cutting options, user-friendly design, and commitment to safety, it is an excellent choice for anyone seeking to maintain a beautiful lawn with minimal effort.
Top Page Image Contents