Sears 917.25271 owner manual Adjustments, To Level Mower Housing

Page 21

Ulnlll

ill

ill i

ii

iii i i i iii

i i Ull iii i iiiinllll

i

m

 

 

 

SERVICE

AND ADJUSTMENTS

 

 

IIII

III I111

I

I III IIIIIm

 

II III

IIIIIIIIIIII

III

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See "PRODUCT SPECIFICATIONS" on page 3 of this manual). Iftires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 22 and 23)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height

from bottom edge of mower to ground. Distance "A" on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE

BOTTOM

EDGE

OF MOWER TO

OF MOWER TO

GROUND

GROUND

 

GROUND LINE

FIG. 22

SUSPENSION

ARM

LIFT LINK

ADJUSTMENTNUT

FIG. 23

FRONT-TO-BACK ADJUSTMENT (See Figs. 24 and 25)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO- SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/4" to 3/4" lower than the rear when the mower is in its highest position.

Check adjustment on right side of tractor. Measure dis- tance "D" directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length. Both links should be approximately 10-3/8".

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut "E" on both front links an equal number of turns.

•When distance "D" is 1/4" to 3/4" lower at front than

rear, tighten nuts "F" against trunnion on both front links.

•To raise front of mower, loosen nut"F" from trunnion on both front links. Tighten nut "E" on both front links an equal number of turns.

•When distance "D" is 1/4" to 3/4" lower at front than rear, tighten nut"F" against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

FIG. 24

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT "E"

NUT "F"

ii

FRONT LINKS

TRUNNION

21

FIG. 25

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Page Safe Operation Practices for Ride-On Mowers Safety RulesMaintenance Agreement Product SpecificationsLimited 90 DAY Warranty on Battery Contents Performance Engine MaintenanceContents To Remove Tractor from Carton Tools Required for AssemblyBefore Rolling Tractor OFF Skid Unpack CartonHOW to SET UP Your Tractor AssemblyPrepare Battery See Figs a and 2B Install Seat See FigCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemInstall Mulcher Plate ChecklistSee Figs a & 7B To Convert to Bagging or DischargingKnow Your Tractor OperationTo Move Forward and Backward HOW to USE Your TractorTo Operate Mower See Fig Before Starting the EngineTo Operate on Hills Check Engine OIL Level See FigADD Gasoline To Start Engine See FigPurge Transmission Mulching Mowing Tips Mowing TipsGeneral Recommendations Lubrication ChartLub.caoncha Before Each USETractor Customer ResponsibilitiesBrake Operation TiresTransaxle Cooling EngineTransaxle Pump Fluid AIR Filter See FigEngine OIL Filter CleaningMuffler Spark PlugsService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing AdjustmentsService To Adjust Brake See FigTo Replace Mower Blade Drive Belt See Fig To Adjust Motion Control Lever See Fig Adjustm NTSTransmission REMOVAL/REPLACEMENT To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery To Adjust Steering Wheel AlignmentFront Wheel TOE-IN/CAMBER See FigTo Replace Headlight Bulb To Remove Hood and Grill AssemblyInterlocks and Relays To Replace FuseTo Adjust Throttle Control Cable To Adjust Carburetor See FigSee Other StorageProblem Cause Correction Troubleshooting PointsProblem Cause Service Notes Tractor - Model Number JlJElectrical Tractor --MODEL NumberKEY Part NO. NO.DESCRIPTION Tractor -- Model NumberChassis and Enclosures KEY Part Description Drive Repair Parts Steering Assembly Steering Wheel Axle Assembly, Front Spindle Assembly, LH 4218 Engine122439X UNC Seat AssemblyWheels & Tires Decals161718 Mower LiftBIkZinc 73800800 Nut LockW/Wsh 13 Unc 139868 Arm Suspension Mower Deck Inch = Tractor - Model Number Hydro Gear Transaxle Model Number 142930 Kohler ENGINE- Model Number MV18.OS, Type Number PS58560 D,,RUD,,IAIR Intake KEY Part Description Kohler Engine Model Number MV18.OS, Type Number PS58560Carbu Retor J Crankcase Dipstick Screw 1/4-20 x 5/8 Service Notes Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation Model no If YOU Need Repair Service or PartsPage Safety Rules Maintenance Agreement Contents Accessories Attachments Contents Assem BLY Assembly Check Tire Pressure Checklist Operation HOW to USE Your Tractor Before Starting the Engine Fii AcAuieverenIioiiii Operation SE.V.C Customer Responsibilities Engine Cleaning Service and Adjustments Adjustments Service Adjustm NTS Service and Adjustments Adjustments Sc. w Storage Troubleshooting Points Problem Cause Service Notes JlJ Repair Parts Tractor -- Model Number Tractor - Model Number KEY Part Description Drive Repair Parts Steering Assembly Tractor -- Model Number Spark Arrester 122439X Tractor -- Model Number Tractor --MODEL Number Tractor - Model Number BIkZinc 73800800 Nut LockW/Wsh 13 Unc 139868 Arm Suspension Tractor --MODEL Number Tractor - Model Number Tractor - Model Number Hydro Gear Transaxle Model Number 142930 D,,RUD,,I Tractor --MODEL Number Tractor --MODEL Number Tractor - Model Number Tractor -- Model Number Screw 1/4-20 x 5/8 Service Notes Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation HP Twin Cylinder Electric Start

917.25271 specifications

The Sears 917.25271 is a robust and versatile garden tractor that has earned its place in the hearts of gardening enthusiasts and lawn care professionals alike. With its impressive blend of features, technologies, and characteristics, this tractor is designed to meet various landscaping and maintenance needs while ensuring user satisfaction and operational efficiency.

One of the standout features of the Sears 917.25271 is its powerful engine. Equipped with a strong and reliable gas-powered engine, the tractor delivers ample horsepower to tackle even the toughest mowing jobs. This ensures that users can efficiently manage their lawns, regardless of terrain type or grass thickness. The smooth operation of the engine is complemented by an easy-to-use ignition system, allowing users to start the tractor with minimal effort.

The design of the 917.25271 prioritizes comfort and usability. Its ergonomic seat provides ample cushioning, reducing fatigue during longer mowing sessions. The adjustable seat allows users of different heights to find their optimal driving position, enhancing overall comfort and control. Moreover, the tractor features a user-friendly control panel, enabling easy access to all essential functions such as speed adjustments, blade engagement, and throttle control.

Another notable technology incorporated into the Sears 917.25271 is its advanced cutting system. The tractor includes a durable mower deck that ensures a clean and even cut, contributing to a well-maintained lawn appearance. The ability to easily adjust the cutting height makes it adaptable to different grass types and seasonal variations, ensuring efficient lawn care throughout the year.

Durability is a key characteristic of the 917.25271. Constructed with high-quality materials, it is designed to withstand the rigors of outdoor use. The reinforced chassis and strong tires provide excellent traction and stability on varied terrain, making it suitable for larger lawns and uneven landscapes.

Additionally, the Sears 917.25271 offers versatility through its attachment options. Users can enhance the tractor's capabilities with various accessories such as snow plows, baggers, and tillers. This adaptability allows it to serve multiple functions, making it a valuable tool not just for mowing, but for year-round landscaping projects.

In conclusion, the Sears 917.25271 stands out for its powerful engine, user-friendly design, advanced cutting technology, and unmatched durability. These attributes make it an essential choice for anyone looking to simplify their lawn care routines and achieve professional results.
Top Page Image Contents