Sears 917.25271 owner manual Fii AcAuieverenIioiiii

Page 74

iiiiii

i

i

i

i

i

i

i

i

OPERATION

ADD GASOLINE

•Fill fuel tank. Use fresh, clean, regular unleaded gasoline. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life).

IMPORTANT" WHEN OPERATING IN TEMPERATURES

BELOW 32°F(0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP INSURE GOOD COLD WEATHER STARTING.

WARNING: Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before stor- age of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instruc- tions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

ii

CAUTION: Fill to bottom of gas tank filler neck. Do not overfill. Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

TO START ENGINE (See Fig. 9)

When starting engine for the first time or if engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

•Depress clutch/brake pedal and set parking brake.

•Place motion control lever in neutral (N) position.

•Move attachment clutch to "DISENGAGED" position.

•Pull choke control out to choke (J\i) position for cold

engine start. For warm engine start do not use choke control.

•Move throttle control to midway between fast (,_) and slow (._b) positions.

•Insert key into ignition and turn key clockwise to"START" position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If engine does not start after several attempts, move throttle control to fast (,_) position, wait a few minutes and try again.

•When engine starts, slowly push choke control in.

•Move throttle control to fast (,t_) position.

•Allow engine to warm up for a few minutes before engaging drive or attachments.

IMPORTANT: COLD STARTING FOR HYDRO (BELOW 40°F) - AFTER STARTING ENGINE AND BEFORE

DRIVING, LET TRANSMISSION WARM UP FOR ONE (1) MINUTE BY PLACING MOTION CONTROL LEVER IN

NEUTRAL (N) POSITION AND RELEASING CLUTCH/ BRAKE PEDAL.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32°F), the carburetor fuel mixture may need to be adjusted for best engine performance. See

'`TOADJUST CARBURETOR" in the Service and Adjust- ments section of this manual.

PURGE TRANSMISSION

fii AcAui"everenIioiiii. i

freewheel lever while the engine is run- ning.

i

iii i

i i

IIH iii

i

To ensure proper operation and performance, it is recom- mended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have devel- oped during shipping of your tractor.

IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE

REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD BE PURGED AFTER REINSTALLATION

BEFORE OPERATING THE TRACTOR.

•Place tractor safely on level surface with engine off and parking brake set.

•Disengage transmission by placing freewheel control in freewheeling position (See "TO TRANSPORT" in this section of manual).

•Sitting in the tractor seat, start engine. After the engine

is running, move throttle control to slow (,gb) position. With motion control lever in neutral (N) position, slowly disengage clutch/brake pedal.

•Move motion control lever to full forward position and hold for five (5) seconds. Move lever to full reverse position and hold for five (5) seconds. Repeat this procedure three (3) times.

NOTE: During this procedure there will be no movement of drive wheels. The air is being removed from hydraulic drive system.

•Move motion control leverto neutral (N) position. Shut- off engine and set parking brake.

•Engage transmission by placing freewheel control in driving position (See '`TOTRANSPORT" in this section of manual).

•Sitting inthe tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed.

With motion control lever in neutral (N) position, slowly disengage clutch/brake pedal.

•Slowly move motion control lever forward, after the tractor moves approximately five (5) feet, slowly move motion control lever to reverse position. After the tractor moves approximately five (5) feet return the motion control lever to the neutral (N) position. Repeat

this procedure with the motion control lever three (3) times.

•Your tractor is now purged and now ready for normal operation.

14

Page 73 Page 75
Image 74
Page 73 Page 75
Contents Page Safety Rules Safe Operation Practices for Ride-On MowersLimited 90 DAY Warranty on Battery Maintenance AgreementProduct Specifications Contents Engine Maintenance PerformanceContents Before Rolling Tractor OFF Skid Tools Required for AssemblyTo Remove Tractor from Carton Unpack CartonPrepare Battery See Figs a and 2B AssemblyHOW to SET UP Your Tractor Install Seat See FigCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemSee Figs a & 7B ChecklistInstall Mulcher Plate To Convert to Bagging or DischargingOperation Know Your TractorHOW to USE Your Tractor To Move Forward and BackwardTo Operate on Hills Before Starting the EngineTo Operate Mower See Fig Check Engine OIL Level See FigPurge Transmission ADD GasolineTo Start Engine See Fig Mowing Tips Mulching Mowing TipsLub.caoncha Lubrication ChartGeneral Recommendations Before Each USEBrake Operation Customer ResponsibilitiesTractor TiresTransaxle Pump Fluid EngineTransaxle Cooling AIR Filter See FigMuffler CleaningEngine OIL Filter Spark PlugsTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Adjustments To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig ServiceTo Adjust Brake See Fig Transmission REMOVAL/REPLACEMENT Adjustm NTSTo Adjust Motion Control Lever See Fig To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel AlignmentTo Start Engine with a Weak Battery See FigInterlocks and Relays To Remove Hood and Grill AssemblyTo Replace Headlight Bulb To Replace FuseSee To Adjust Throttle Control CableTo Adjust Carburetor See Fig Storage OtherTroubleshooting Points Problem Cause CorrectionProblem Cause Service Notes JlJ Tractor - Model NumberTractor --MODEL Number ElectricalTractor -- Model Number KEY Part NO. NO.DESCRIPTIONChassis and Enclosures KEY Part Description Drive Repair Parts Steering Assembly Steering Wheel Axle Assembly, Front Spindle Assembly, LH Engine 4218122439X Seat Assembly UNCDecals Wheels & TiresMower Lift 161718BIkZinc 73800800 Nut LockW/Wsh 13 Unc 139868 Arm Suspension Mower Deck Inch = Tractor - Model Number Hydro Gear Transaxle Model Number 142930 D,,RUD,,I Kohler ENGINE- Model Number MV18.OS, Type Number PS58560Kohler Engine Model Number MV18.OS, Type Number PS58560 AIR Intake KEY Part DescriptionCarbu Retor J Crankcase Dipstick Screw 1/4-20 x 5/8 Service Notes Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation If YOU Need Repair Service or Parts Model noPage Safety Rules Maintenance Agreement Contents Accessories Attachments Contents Assem BLY Assembly Check Tire Pressure Checklist Operation HOW to USE Your Tractor Before Starting the Engine Fii AcAuieverenIioiiii Operation SE.V.C Customer Responsibilities Engine Cleaning Service and Adjustments Adjustments Service Adjustm NTS Service and Adjustments Adjustments Sc. w Storage Troubleshooting Points Problem Cause Service Notes JlJ Repair Parts Tractor -- Model Number Tractor - Model Number KEY Part Description Drive Repair Parts Steering Assembly Tractor -- Model Number Spark Arrester 122439X Tractor -- Model Number Tractor --MODEL Number Tractor - Model Number BIkZinc 73800800 Nut LockW/Wsh 13 Unc 139868 Arm Suspension Tractor --MODEL Number Tractor - Model Number Tractor - Model Number Hydro Gear Transaxle Model Number 142930 D,,RUD,,I Tractor --MODEL Number Tractor --MODEL Number Tractor - Model Number Tractor -- Model Number Screw 1/4-20 x 5/8 Service Notes Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation HP Twin Cylinder Electric Start

917.25271 specifications

The Sears 917.25271 is a robust and versatile garden tractor that has earned its place in the hearts of gardening enthusiasts and lawn care professionals alike. With its impressive blend of features, technologies, and characteristics, this tractor is designed to meet various landscaping and maintenance needs while ensuring user satisfaction and operational efficiency.

One of the standout features of the Sears 917.25271 is its powerful engine. Equipped with a strong and reliable gas-powered engine, the tractor delivers ample horsepower to tackle even the toughest mowing jobs. This ensures that users can efficiently manage their lawns, regardless of terrain type or grass thickness. The smooth operation of the engine is complemented by an easy-to-use ignition system, allowing users to start the tractor with minimal effort.

The design of the 917.25271 prioritizes comfort and usability. Its ergonomic seat provides ample cushioning, reducing fatigue during longer mowing sessions. The adjustable seat allows users of different heights to find their optimal driving position, enhancing overall comfort and control. Moreover, the tractor features a user-friendly control panel, enabling easy access to all essential functions such as speed adjustments, blade engagement, and throttle control.

Another notable technology incorporated into the Sears 917.25271 is its advanced cutting system. The tractor includes a durable mower deck that ensures a clean and even cut, contributing to a well-maintained lawn appearance. The ability to easily adjust the cutting height makes it adaptable to different grass types and seasonal variations, ensuring efficient lawn care throughout the year.

Durability is a key characteristic of the 917.25271. Constructed with high-quality materials, it is designed to withstand the rigors of outdoor use. The reinforced chassis and strong tires provide excellent traction and stability on varied terrain, making it suitable for larger lawns and uneven landscapes.

Additionally, the Sears 917.25271 offers versatility through its attachment options. Users can enhance the tractor's capabilities with various accessories such as snow plows, baggers, and tillers. This adaptability allows it to serve multiple functions, making it a valuable tool not just for mowing, but for year-round landscaping projects.

In conclusion, the Sears 917.25271 stands out for its powerful engine, user-friendly design, advanced cutting technology, and unmatched durability. These attributes make it an essential choice for anyone looking to simplify their lawn care routines and achieve professional results.
Top Page Image Contents