McCulloch 115249726 HOW to Stop Your Unit, HOW to Start Your Unit, Starting a Flooded Engine

Page 10

empty the fuel system before storage for 30 days or longer. Drain the fuel tank, start the en- gine and let it run until the fuel lines and carbure- tor are empty. Use fresh fuel next season. Nev- er use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

HOW TO STOP YOUR UNIT

SStop the engine by pushing and holding the ON/STOP switch in the STOP position until the engine stops.

ON/STOP switch

HOW TO START YOUR UNIT

WARNING: Avoid any contact with the muffler. A hot muffler can cause serious burns.

STARTING A COLD ENGINE (or a warm engine after running out of fuel)

Starting position

Primer Starter

Throttle bulb handle lock--out

NOTE: Normally, the warm starting procedure can be used within 5 -- 10 minutes after the unit is turned off. If the unit sits for more than 10 min- utes without being run, it will be necessary to start the unit by following the steps under STARTING A COLD ENGINE or following the starting instruction steps shown on the unit.

STARTING A FLOODED ENGINE

Move the start lever to the RUN position and fully squeeze throttle trigger. Pull the starter handle repeatedly while squeezing throttle trigger until engine starts and runs. This could require pulling the starter handle many times, depending on how badly the unit is flooded. If the unit still doesn’t start, refer to TROUBLE-

SHOOTING TABLE.

OPERATING THE COUPLER

This model is equipped with a coupler which enables optional attachments to be installed.

WARNING: Always stop unit and dis- connect spark plug before removing or instal- ling attachments.

REMOVING TRIMMER ATTACH- MENT (OR OTHER OPTIONAL AT- TACHMENTS)

CAUTION: When removing or installing at- tachments, place the unit on a flat surface for stability.

1.Loosen the coupler by turning the knob counterclockwise.

Coupler

AttachmentLOOSEN

ThrottleMuffler trigger Start

lever

NOTE: The throttle lock--out is designed to prevent unintentional use of the throttle trig- ger. The lock--out must be pressed with the palm of your hand as you grip the throttle han- dle before the trigger can be used. DO NOT squeeze the throttle trigger until the engine has started and runs.

1.Set unit on a flat surface.

2.Slowly press the primer bulb 6 times.

3.Move the start lever to the START position.

4.Pull starter rope handle sharply until en- gine starts and runs.

5.Allow unit to run for 10--15 seconds, then fully squeeze the throttle trigger to disen- gage the starting system.

STARTING A WARM ENGINE

Pull starter rope sharply until engine starts and runs.

Knob

TIGHTEN

2. Press and hold the locking/release button.

Locking/Release

Button

Attachment

Coupler

Upper Shaft

3.While securely holding the engine and up- per shaft, pull the attachment straight out of the coupler.

INSTALLING OPTIONAL ATTACH- MENTS

1.Remove the shaft cap from the attach- ment (if present).

2.Position locking/release button of attach- ment into guide recess of coupler.

3.Push the attachment into the coupler until the locking/release button snaps into the primary hole.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Betriebsanweisung Manuel D’INSTRUCTIONSManual DE Instrucciones Table of Contents Identification What is WHAT?Identification of Symbols Safety RulesHazard Zone Operator SafetyUnit / Maintenance Safety Are doing use common senseAssembly Attaching the Handle Installing Trimmer AttachmentAssembly of Shoulder Strap To Relocate Shoulder Strap ClampAssembly Information Trimmer Head Configuring Your UnitAttaching the Plastic Shield and Trimmer Head Attaching the Metal Shield Assembly Information Weed BladeInstallation of the Metal Blade Wrench Nut Gearbox Dust cup Aligned holes Retaining washerFueling Engine OperationAttaching the Transport Guard GuardInstalling Optional ATTACH- Ments HOW to Stop Your UnitHOW to Start Your Unit Starting a Flooded EngineTrimmer Line Advance Operating PositionOperating Instructions for USE with Trimmer Head Cutting MethodsCm above ground Operating Instructions for USE with Weed BladeTrimming MowingEdger Safety Additional Safety RulesBLOWER/VACUUM Safety Pole Pruner Safety Cultivator SafetyHedge Trimmer Safety AttachedCm in diameter Snow Thrower SafetySpeed when not pruning AnotherMaintenance Service and AdjustmentsCover Spool Remove any remaining line Engine will not idle when the throttle is re- leased Blade ReplacementCarburetor Adjustment StorageEngine Troubleshooting Table Cause RemedySeasonal Storage OtherEC Declaration of Conformity Only applies to Europe Declaration of Conformity09--1--31 Technical Data Noise Levels Octave Band Analysis 100-10000hz 1/3 Octave

115249726 specifications

The McCulloch 115249726 is a robust chainsaw designed to meet the needs of both DIY enthusiasts and professional users. Known for its powerful performance and user-friendly features, this chainsaw has become a popular choice for those looking to tackle various cutting tasks, from tree trimming to firewood preparation.

One of the standout features of the McCulloch 115249726 is its reliable engine. Equipped with a strong, high-performance two-stroke engine, it delivers ample power for demanding cutting jobs. This engine provides a perfect balance between efficiency and performance, ensuring that users can rely on the chainsaw to handle tougher materials without straining the machine. The chainsaw operates at optimal speeds, allowing for smooth and quick cuts.

Another essential characteristic of the McCulloch 115249726 is its lightweight design. Weighing in at a manageable weight, this chainsaw is designed for ease of handling, reducing user fatigue during extended use. Its ergonomic handle ensures a comfortable grip, enhancing user control and stability. The chain brake feature adds an extra layer of safety by immediately stopping the chain in the event of kickback, making this chainsaw ideal for both experienced and novice users.

The McCulloch 115249726 also boasts advanced technology to enhance performance and longevity. One key technology is its automatic oiler system, which keeps the chain lubricated during use, minimizing wear and tear. This system not only extends the lifespan of the chain and bar but also ensures optimal cutting efficiency. The chainsaw is designed for easy maintenance, which includes tool-less chain tensioning, allowing users to quickly adjust the chain for the best cutting results.

Furthermore, the McCulloch 115249726 is equipped with an easy-start system that reduces the effort required to start the engine, making it more accessible for users of all skill levels. Its durable construction ensures that it can withstand the rigors of tough outdoor conditions, making it a reliable companion for all your cutting needs.

In summary, the McCulloch 115249726 combines power, efficiency, and safety features to deliver a superior chainsaw experience. With its robust engine, user-friendly design, and advanced technologies, it stands out as an excellent choice for anyone seeking a reliable tool for their cutting projects. Whether for occasional use or professional applications, this chainsaw offers the performance and features required to tackle any job effectively.
Top Page Image Contents