Troy-Bilt 52058, 52057 owner manual Troubleshooting, Problem Possible Cause Correction

Page 19

Section 5: Maintenance

TROUBLESHOOTING

Before performing any of the corrections in this Troubleshooting Chart, refer to the appropriate information contained in this Manual or the Engine Owner’s Manual for the correct safety precautions and servicing procedures. Contact your local autho- rized Engine Service Dealer for engine service. Contact your local authorized dealer for service problems with the machine.

PROBLEM

 

POSSIBLE CAUSE

 

CORRECTION

 

 

 

 

 

Engine does not start.

1.

Spark plug wire disconnected.

1.

Reconnect wire.

 

2.

Defective or incorrectly gapped spark plug.

2.

Inspect/replace spark plug.

 

3.

Fuel tank empty.

3.

Add fuel.

 

4.

Dirty carburetor or fuel line.

4.

Clean carburetor or fuel line.

 

5.

Dirty air cleaner.

5.

Clean or replace.

 

6.

Carburetor out of adjustment.

6.

Adjust carburetor. See Engine Service Dealer.

 

7.

Engine flooded.

7.

Wait several minutes before starting.

 

8.

Engine Throttle Lever in incorrect position.

8.

Move Throttle Lever to FAST position.

 

9.

Stale gasoline.

9.

Drain old fuel and add fresh fuel.

 

10.

Defective Engine Throttle Lever.

10.

See Engine Service Dealer.

 

11.

Dirt or water in fuel tank.

11.

See Engine Service Dealer.

 

 

 

 

 

Engine runs poorly.

1.

Bad spark plug.

1.

Inspect/replace spark plug.

 

2.

Dirty air filter.

2.

Clean or replace.

 

3.

Carburetor out of adjustment.

3.

Adjust carburetor. See Engine Service Dealer.

 

4.

Stale fuel.

4.

Drain and replace fuel mixture.

 

5.

Dirt or water in fuel tank.

5.

See Engine Service Dealer.

 

6.

Engine cooling system clogged.

6.

Clean fins.

 

 

 

 

Engine overheats.

1.

Engine cooling system clogged.

1. Clean air cooling areas and behind debris shield.

 

2.

Carburetor out of adjustment.

2.

Adjust Carburetor. See Engine Service Dealer.

 

 

 

 

 

Engine does not shut off.

1.

Throttle control misadjusted.

1.

See Engine Service Dealer.

 

 

 

 

 

.

1.

Line length is too short or too long.

1.

Adjust line length to 18" long. When less

Poor mowing performance.

 

 

 

 

than 1/2 this length, replace the line.

 

2.

Cutting height is too high or low for height

2.

Adjust cutting height to approximately 1/3

 

 

of grass being cut.

 

of the length of the grass.

 

3.

Engine not set at FAST speed.

3.

Move Engine Throttle Lever to FAST (Rabbit).

 

 

 

 

 

Trimmer/Mower vibrates.

1.

Trimming head mounting bolt loose.

1.

Tighten bolt.

 

2.

Line lengths are substantially different.

2.

Adjust lines to approximately equal lengths.

 

3.

Loose nuts or bolts.

3.

Check all bolts and nuts, including engine bolts.

 

4. Broken spindle head or trimmer head.

4.

Replace broken part.

 

 

 

Trimmer head does not

1. Incorrect line installation for mowing conditions.

1. See Changing Trimmer Lines in Section 5.

retain line.

 

 

 

 

 

 

 

 

 

Trimmer Head does not

1.

Head bolts may be loose.

1.

Tighten head bolts to 75 in/lbs.

retain height setting.

2.

Head is worn.

2.

Replace head assembly.

 

 

 

 

 

Electric Starter does not

1.

Wires to battery unconnected.

1.

Reconnect wires.

start engine (electric start

2.

Battery not charged.

2.

Charge battery.

models only).

3.

Broken wire in wiring harness.

3.

Replace wiring harness.

 

4.

Malfunctioning starter motor.

4.

Contact local engine dealer.

 

 

 

 

 

Battery does not charge

1.

Broken wire in engine recharging circuit.

1.

See Engine Service Dealer.

during engine operation

2.

Malfunctioning engine recharging system.

2.

See Engine Service Dealer.

(electric start models).

3.

Dead battery.

3.

Replace battery.

 

 

 

 

 

Battery charger does not

1.

Broken battery lead.

1.

Replace battery lead.

charge battery (electric

2.

Broken battery charger wire.

2.

Replace battery charger.

start models).

3.

Dead battery.

3.

Replace battery.

 

 

 

 

 

17

Image 19
Contents Trimmer/Mower See Back Cover for Customer Service Information Do not put SafetyRemove key on electric start model Use only an approved container Do notUse this equipment for its intended purpose only Do not allow children nearby if you are workingReplacing the trimmer lines. Let the engine cool Never make adjustments or repairs while engine is runningNever run the engine inside a closed area Trimmer line movesTools/Supplies Needed AssemblyTo the outside of the handlebar From the hardware bagSpecified hardware Use a high-quality, SAE 30 weightAttach Throttle Control Lever Mix oil with fuelLift and tilt debris shield X, Figure Connect and Charge Battery Electric Start ModelsFeatures and Controls Features and ControlsIntroduction PRE-START ChecklistAdjust Line Cutting Height OperationOperating TRIMMER/MOWER Using the Trimmer Head Control BailUSE the Correct Diameter Trimmer Line Additional Operating Tips and Techniques Required Maintenance MaintenanceRequired Maintenance Schedule Adjusting Trimmer Head EngagementBelt Removal Removing and Replacing the Trimmer HeadInspecting / Replacing the Drive Belt Belt InspectionKR T Belt ReplacementLubrication Cleaning the Engine Debris GuardGeneral Engine Maintenance TRIMMER/MOWER Cleaning and Debris RemovalStore machine on a level surface Battery ReplacementThrottle Control Adjustment OFF-SEASON StorageMentals to help prevent girdling cut- ting of bark Changing Trimmer LinesTo Change Trimmer Lines Problem Possible Cause Correction TroubleshootingDrawing no Parts ListRef. # Description Qty Parts List Drawing noRef. # Description Parts ListModels 52057Accessories and Kits Drawing no Parts List Drawing noEngine Service and Repair Warranty ServiceCustomer Service and Technical Service Replacement Parts

52058, 52057 specifications

The Troy-Bilt 52058 and 52057 are two impressive models in the Troy-Bilt lineup, known for their power, durability, and ease of use, making them popular choices for homeowners and garden enthusiasts alike.

The Troy-Bilt 52058 boasts a robust 306 cc OHV engine, providing the necessary power to tackle even the toughest of garden tasks. This model features a 24-inch cutting width, allowing it to cover large areas quickly. The Rear Tine Tiller design further enhances its capability, as it digs deep into the soil with its heavy-duty tines, ensuring that your garden bed can be prepared with minimal effort. One of the standout features is its patented forward and reverse tilling capability, which improves maneuverability and efficiency.

On the other hand, the Troy-Bilt 52057 comes with a slightly smaller 250 cc engine but remains powerful in its own right. It also incorporates a 16-inch tilling width, making it suitable for smaller gardens or tighter spaces. This model is engineered with a gear-driven transmission, providing superior handling and control while tilling. The adjustable tilling depth feature allows users to customize their tilling experience, whether they're breaking new ground or maintaining existing beds.

Both models are equipped with an ergonomic handle design, ensuring that users remain comfortable during prolonged use. The intuitive controls are easily accessible, allowing for smooth operation even for those who may not have extensive experience with gardening equipment. Additionally, Troy-Bilt has included a sturdy rear-wheel design in both models, which ensures stability and ease of movement across various terrains.

In terms of technology, these tillers are equipped with advanced features that maximize efficiency. The performance-enhancing tilling tines are designed to break up soil efficiently, reducing the time and effort needed for garden preparation. Furthermore, these models comply with modern emissions regulations, making them environmentally friendly choices for today’s gardeners.

Overall, the Troy-Bilt 52058 and 52057 represent a perfect blend of power, versatility, and user-friendly design. Whether you are preparing soil for planting or maintaining existing flower beds, these tillers offer the dependability and performance needed to achieve gardening success. With their strong build quality and thoughtful engineering, they are excellent investments for anyone serious about gardening.