Troy-Bilt LS 27 TB warranty Preparing the Log Splitter

Page 7

3.Disconnect the log cradle from the beam on the side of the control valve. See Figure 3-5.

4.Lift and slide the cylinder up to the top of beam and into the weld brackets. See Figure 3-6.

5.Attach the dislodger over the wedge assembly and secure with hardware, previously removed, to the weld brackets.

NOTE: Once the six hex screws are tightened, there may be a slight gap between the dislodger and the weld brackets. This gap is normal.

6.Reattach the log cradle to the side of the beam with the control valve, aligning the ends of the cradle with the beam flanges.

7.Roll log splitter off the bottom crate.

Preparing the Log Splitter

1.Lubricate the beam area (where the splitting wedge will slide) with engine oil; do not use grease.

2.Remove vented reservoir dipstick, which is located in front of the engine on top of the reservoir tank. See Figure 3-7.

IMPORTANT: The log splitter may have been shipped and primed with hydraulic fluid in the reservoir tank. However, you MUST check the fluid level before operat- ing. If not filled, proceed with the following steps:

3.Fill the reservoir tank with hydraulic fluid included with this unit (if equipped) or approved fluids which include Dexron® III / Mercon® III automatic transmission fluid, a 10 Weight AW hydraulic oil or Pro-Mix™ AW-32 Hydraulic Oil.

4.Check fluid level using the dipstick. See Figure 3-7. Do not overfill.

5.Replace vented dipstick securely, tightening it until the top of the threads are flush with top of the pipe.

6.Disconnect the spark plug and prime the pump by pulling the recoil starter as far as it will go. Repeat approximately 10 times.

7.Reconnect the spark plug wire and start engine following instructions in the OPERATION section.

8.Use control handle to engage the wedge to the farthest extended position. Then retract the wedge.

9.Refill tank as specified on the dipstick.

NOTE: Failure to refill the tank will void unit’s warranty.

10.Extend and retract the wedge 12 complete cycles to remove trapped air in the system (the system is “self-bleeding”).

11.Refill reservoir within range marked on the dipstick.

WARNING: Much of the original

fluid has been drawn into the cylinder and hoses. Make certain to refill the reservoir to prevent damage to the hydraulic pump.

Figure 3-5

Figure 3-6

Figure 3-7

NOTE: Some fluid may overflow from the vent plug as the system builds heat and the fluid expands and seeks a balanced level.

3

Setting Up

Your Log

Splitter

WARNING

Much of the original fluid has been drawn into the cylinder and hoses. Make certain to refill the reservoir to prevent damage to the hydraulic pump.

IMPORTANT: The log splitter may have been shipped and primed with hydraulic fluid in the reservoir tank. If not, proceed with the following steps:

NOTE: Some fluid may overflow from the vent plug as the system builds heat and the fluid expands and seeks a balanced level.

Page 6 Page 8
Image 7
Page 6 Page 8
Contents MTD LLC, P.O. BOX 361131 CLEVELAND, Ohio LS 27 TB Log Splitter04/25/2007 Finding and Recording Model Number Table of ContentsCustomer Support Safety Labels Found On Your Log Splitter Safety LabelsGeneral Practices Your ResponsibilityPreparation Operation Maintenance and Storage Attaching the Jack Stand Setting Up Your Log SplitterConnecting Cylinder to Beam Assembling the TonguePreparing the Log Splitter Wedge Know Your Log SplitterBeam Locks Engine ControlsControl Handle Operating Your Log SplitterStopping Engine Gas and Oil Fill-UpBefore Each Use Using the Log SplitterOperating Tips To lower the beam Raising and Lowering BeamTransporting the Log Splitter NeverMaintaining Your Log Splitter Gib AdjustmentWedge Assembly Adjustment Conditions that Will Void WarrantyEngine Hydraulic Fluid and Inlet FilterBeam and Splitting Wedge Hose ClampsSide View-Coupler 0600 Install nylon spider onto engine coupling halfTires Set ScrewReplace spark plug Storing Your Log SplitterCause Remedy Problem Cause RemedyRetracting Engine stalls during Low horsepower/weak engineService dealer Conditions Low horsepower/weak engineModel LS 27 TB 1800828-5500 Parts ListDescription MANUFACTURER’S Limited Warranty for LS 27 TB Máquina rompetroncos Manual DEL OperadorAsistencia a través de su distribuidorTroy-Bilt ÍndiceBúsqueda y registro del número de modelo Asistencia al clienteAdvertencia Etiquetas SeguridadNo ajuste los valores de presión de la bomba o válvula ResponsabilidadPrácticas generales PreparativosMiento FuncionamientoSu responsabilidad Del combustibleManipulación mecánico Montaje de la lengüetaColocación del gato Colocación de la lengüetaHaga rodar el tronco fuera de la caja de abajo Preparación de la máquina rompetroncosControles del motor Bloqueos de la viguetaEncendido del motor Detención del motorFuncionami Ento de la Máquina Rompetroncos Manija de controlUso de la máquina rompetroncos Antes de cada usoConsejos de operación Nunca Elevación y descenso de la viguetaConecte las cadenas de seguridad al vehículo de remolque Ajuste del montaje de la cuña Ajuste del retenedorCondiciones que anulan la garantía Motor Fluido hidráulico y filtro de entradaVigueta y cuña de corte Abrazaderas de la mangueraTornillo de fijación Vista lateral Acoplador NeumáticosSujete con las tuercas extraidas anteriormente Limpie la máquina rompetroncos por completo Almacenamiento de la máquina rom- petroncosVuelva a colocar la bujía Problema Cause Solución Vuelva a llenarlo Velocidad lenta del ejeDel cilindro durante la El mantenimiento Velocidad del motor lentaModelo LS 27 TB Nº de pieza Descripción Lista de PiezasGarantía Limitada DEL Fabricante Para

LS 27 TB specifications

The Troy-Bilt LS 27 TB is an innovative garden tiller designed to enhance productivity in any small to medium-sized gardening or landscaping project. This robust machine features a powerful engine and advanced technologies that streamline the tilling process, making it a valuable tool for both amateur gardeners and seasoned horticulture professionals.

One of the standout features of the LS 27 TB is its 27-inch tilling width. This ample width allows users to cover more ground in less time, reducing the number of passes required to prepare the soil. The tiller's adjustable tilling depth—ranging from 1 to 8 inches—enables precise soil preparation for varying plant root depths, ensuring optimal growing conditions for various crops.

Powered by a reliable, easy-start engine, the Troy-Bilt LS 27 TB offers ample horsepower to tackle tough soil conditions without compromising performance. The machine's forward and reverse gear options provide enhanced maneuverability, allowing gardeners to navigate tight corners and difficult spots with ease.

Incorporated into the design is the patented “Cultivator Attachment” system, which allows users to switch from tilling to cultivating tasks effortlessly. This versatility makes the LS 27 TB an excellent choice for multi-purpose gardening, as it can handle not only tilling but also other gardening tasks efficiently.

Safety is a priority with the LS 27 TB, which features a handlebar-mounted control system. This ergonomic design provides users with greater comfort while working, reducing fatigue during extended use. The tiller is also equipped with an automatic engagement system for the tines, ensuring that users can operate the machine with confidence.

Another notable characteristic of this tiller is its durable construction. Built to withstand the rigors of frequent use, the Troy-Bilt LS 27 TB features high-quality materials that ensure longevity. The robust wheels provide excellent traction, making it easier to navigate uneven terrain.

In summary, the Troy-Bilt LS 27 TB is a powerful and versatile tiller that combines innovative features, user-friendly controls, and durability. Whether preparing a small garden bed or working on a larger landscaping project, this tiller offers the performance and versatility needed to achieve gardening goals with ease. Its blend of technology and user-centric design sets it apart in the market, making it an ideal choice for anyone looking to enhance their gardening experience.
Top Page Image Contents