Woods Equipment BB7200X, MAN0680, BB8400X, BB6000X manual Quick Hitch SET-UP, Driveline Adjustment

Page 13

1. Tractor top link

2. Cutter top link attachment point

5. Hitch pin

Figure 2. Cutter to Tractor Connection

QUICK HITCH SET-UP

Refer to Figure 3 and Figure 4.

Category I and II for BB6000X, BB7200X

1.CAT I: No adjustment is required.

2.CAT II: Remove hardware securing lift arms to mounting lugs. Move lift arms forward to second holes and insert caps screws. Tighten hardware.

3.Install mounting pins as shown in Figure 4 for correct hitch configuration.

Category II and III for BB8400X

1.CAT II: No adjustment is required.

2.CAT III: Remove hardware securing lift arms to mounting lugs. Move lift arms forward to second holes and insert cap screws. Tighten hardware.

3.Install mounting pins as shown in Figure 4 for correct hitch configuration.

BB6000X, BB7200X

CAT II Position

 

 

 

 

 

 

 

CAT I Position

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CAT III Position

 

 

 

CAT II Position

 

 

BB8400X

Figure 3. Left Rail Mounting Lug

Figure 4. Mounting Pin Installation

DRIVELINE ADJUSTMENT

NOTICE

Avoid contact with driveline when raising cut-

ter.

Make sure driveline will not bottom out at the shortest length and that it has at least 1/3 overlap at the longest length.

With cutter adjusted to transport position, set upper stop on tractor lift quadrant to prevent cutter from contacting the driveline when being raised.

Attach the cutter to the tractor 3-point hitch (or quick hitch if available). Do not attach driveline. Raise and lower cutter to determine maximum and minimum dis- tance between the tractor PTO shaft and the gearbox input shaft. If the distance is too large, the driveline will be too short for proper engagement. If distance is too small, the driveline may bottom out in operation and damage the cutter or tractor.

The driveline length must be sufficient to provide at least 1/3 driveline length of engagement during opera- tion. There must be at least 4 inches of engagement at the cutter’s lowest possible point of operation. The driveline must not bottom out when raised to the maxi- mum height possible.

If driveline is too short, please call your Woods dealer for a longer driveline.

If driveline is too long, please follow the instructions for shortening the driveline.

MAN0680 (11/30/2007)

Operation 13

 

 

Image 13
Contents Brushbulltm To the Dealer IntroductionLEA EL Instructivo Table of ContentsGeneral Information SpecificationsSafety Free Mower Safety VideoTraining Package for Rotary Mowers/Cutters-English/Spanish Training Package for Rotary Mowers/Cutters-EnglishTraining Safety RulesPreparation Operation MaintenanceTransportation Storage Be Careful Safety & Instructional Decals33347E Operation Connecting Cutter to TractorOperation Tractor StabilityQuick Hitch SET-UP Driveline AdjustmentShortening Driveline Check Chain Adjustment Cutting Height AdjustmentDriveline Installation Tractor PTO Driveline Interference CheckShredding Material Operating TechniquePRE-OPERATION Check List Owner Service Owner ServiceBlocking Method Lubrication InformationGearbox Lubrication Slip Clutch AdjustmentDriveline Lubrication Blade Installation Blade ServiceBlade Removal Shielding Repair Cleaning CutterTroubleshooting TroubleshootingMowing Conditions Dealer Service Dealer ServiceGearbox Maintenance Seal ReplacementHorizontal Shaft Leak Repair Vertical Shaft RepairGearbox Repair Gearbox AssemblyRemove Gearbox from Cutter Disassemble GearboxCrossbar Removal Reinstall GearboxJoint Disassembly Crossbar InstallationUniversal Joint Repair Install Bearing Cups Joint AssemblyDealer Service Assembly AssemblyDealer SET-UP Instructions Disassemble Shipping Unit Install TailwheelAssemble Cutter Connect A-Frame ArmsInstall Safety Shielding Install Slip Clutch DrivelineInstall Optional Chain Shielding Install Rubber DeflectorModel Baffle KIT Installation OptionalCheck Chain Installation Optional Dual Tailwheel Installation BB7200X, BB8400X OptionalDealer Check Lists Dealer Check ListPRE-DELIVERY Check List Delivery CheckParts Parts Index BrushbulltmBB6000X, BB7200X & BB8400X Assembly BB6000X, BB7200X & BB8400X Parts List Gearbox Assembly Gearbox Assembly Parts List Slip Clutch Drive Assembly BB7200X & BB8400X Dual Tailwheel Optional Front & Rear Chain Shielding Optional Check Chain Assembly Optional Crossbar Puller Optional SAE Series Torque Chart Bolt Torque ChartMetric Series Torque Chart AppendixAbbreviations Bolt Size ChartIndex IndexWarranty Rev /23/2005 MAN0680