Sterling Plumbing 7114 Series Construire le cadrage, Construct the Framing, Provisions cadrage

Page 12

Construct the Framing (cont.)

Ensure fiber or other soft insulation does not drop down into the water channel. Cover or seal any loose material. Failure to do so may cause wicking of water from the water channel into the insulation which may induce mold, leakage, or mildew. Ensure the channels are free of debris after installation.

For Above-the-Floor Drain Baths

Ensure the drain piping can pass through the wall and that the load bearing requirements of the wall are satisfied. Modify the framing or raise the subfloor as required to obtain clearance.

Construct 2x4 stud framing for your particular installation according to the ″Roughing-In″ section.

Ensure that the framing for each stud is plumb and square within 1/8″ (3 mm). Shimming will be required if tolerances are not met.

If possible, construct an access panel in the plumbing end wall to simplify future maintenance of all plumbing connections.

Construire le cadrage

REMARQUE: Se référer à la section ″plan de raccordement″ pour les dimensions.

Provisions cadrage

AVERTISSEMENT: Risque d’endommagent du produit et de la propriété. La

baignoire doit être supportée par le plancher.

La baignoire avec bandeau doit être fixée aux montants sur trois côtés.

Un plancher doit être installé. La baignoire doit être positionnée de manière à permettre le drainage à travers les charpentes exposées ou dalles et pour faciliter l’installation de la plomberie.

Des montants doivent être approximativement positionnés tel qu’illustré dans la section ″Raccordement″ pour attacher proprement les murs. D’autres emplacements de montant sont optionnels sauf ceux qui doivent être conformes aux codes de bâtiments locaux. Les montants doivent aussi permettre l’installation de raccords de plomberie.

REMARQUE: Si les murs avoisinants seront installés sur un mur en maçonnerie, prendre des dispositions pour les connexions de la plomberie. Pour la plomberie, construire un cadre séparé à un minimum de 6″ (15,2 cm) du mur en maçonnerie. Pour les autres murs, utiliser des tasseaux de 2x2 pour simuler l’emplacement des cales.

S’assurer que le montant extérieur est positionné avec les brides du mur verticales 31-1/4″ (79,4 cm) du mur arrière. Le rebord extérieur du montant devrait s’aligner avec le rebord de la bride du mur.

NOTICE: Les accessoires qui requièrent un renfort ou un support ne sont pas recommandés pour cette installation. Installer ces accessoires pourrait annuler la garantie.

1065823-2-C

12

Sterling

Page 11 Page 13
Image 12
Page 11 Page 13
Contents 1065823-2-C Important Information Tools/Outils/Herramientas Thank You For Choosing Sterling Merci d’avoir choisi SterlingGracias por elegir los productos de Sterling Before You BeginBefore You Begin ADA ConsiderationsAvant de commencer Avant de commencer Considérations ADAAntes de comenzar Antes de comenzar Consideraciones de la ADARoughing-In Plan de raccordement Diagrama de instalación Construct the FramingFraming Provisions Construire le cadrage Construct the FramingFor Above-the-Floor Drain Baths Provisions cadrageConstruya la estructura de postes de madera Construire le cadragePour baignoires à drain au-dessus du sol Estipulaciones para la estructura de postes de maderaPrepare the Subfloor Construya la estructura de postes de maderaPara bañeras con desagüe arriba del nivel del piso Level the Subfloor OptionalPréparer le plancher Prepare el subpisoNiveler le plancher optionnel Install the Rough Plumbing Prepare el subpisoNivele el subpiso opcional Series/Séries 7114/Serie Series/Séries 7124/SerieInstaller la plomberie de raccordement Install the Rough PlumbingInstale las tuberías de plomería Position the Bath Instale las tuberías de plomeríaInstall a Mortar Cement Bed Optional Positionner la baignoirePosition the Bath Installer un lit de mortier Optionnel Coloque la bañeraPositionner la baignoire Coloque la bañera Instale una capa de cemento mortero opcionalPre-Fit the Wall Surrounds Munir les murs avoisinantsAjuste inicial de las paredes circundantes Munir les murs avoisinantsAviso Instale primero la pared posterior Optional Accessories Prepare the Wall SurroundsPrepare the Plumbing End Wall End wallAccessoires optionnels Préparer les murs avoisinantsPréparer le mur d’extrémité de plomberie Côté arrière du mur d’extrémitéPrepare las paredes circundantes Accesorios opcionalesSecure the Wall Surrounds Bath Baignoire BañeraSécuriser les murs avoisinants Secure the Wall SurroundsComplete the Installation Fije las paredes circundantesCompléter l’installation Complete the InstallationTermine la instalación Troubleshooting Symptoms Probable Causes Recommended ActionTermine la instalación Procedimiento para resolver problemas Symptômes Causes probables Action recommandéeDépannage Síntomas Causas probables Acción recomendadaCare and Cleaning Instructions Instructions d’entretien et de nettoyageWarranty Instrucciones de cuidado y limpiezaGarantie GarantíaGarantía Ésta es nuestra garantía exclusiva por escrito

7114 Series specifications

The Sterling Plumbing 7114 Series is a standout line that brings together quality, functionality, and modern design to meet the needs of various bathroom styles. This series is known for its durability and practicality, making it a favored choice among homeowners and professionals alike.

One of the main features of the 7114 Series is its sleek, contemporary design. The lines are clean and minimalistic, ensuring that the products seamlessly fit into modern bathroom aesthetics. The series typically includes fixtures such as faucets, showerheads, and other essential components that not only enhance usability but also elevate the overall look of the space.

In terms of technology, the Sterling 7114 Series is equipped with innovative water-saving features that help reduce water consumption without compromising performance. These fixtures often come with aerators or flow restrictors that ensure a steady stream of water while conserving gallons per minute. This efficiency is not only beneficial for the environment but also helps reduce water bills for homeowners.

Another characteristic that sets this series apart is its ease of installation. Designed with user-friendliness in mind, many products within the 7114 Series feature straightforward mounting and connection options, making it easier for plumbers and DIY enthusiasts to install them. This accessibility has earned the 7114 Series a reputation for being a reliable choice for both new constructions and renovation projects.

Durability is also a notable feature of the Sterling Plumbing 7114 Series. Many fixtures are crafted from high-quality materials, such as solid brass and corrosion-resistant finishes, ensuring they can withstand the rigors of daily use. The finishes are often designed to resist tarnishing and scratching, allowing the products to maintain their aesthetic appeal over time.

Additionally, the Sterling 7114 Series provides a variety of options to suit individual tastes and needs. Customers can choose from different finish options, including polished chrome, brushed nickel, and more, allowing for a custom look that complements their unique bathroom design.

In conclusion, the Sterling Plumbing 7114 Series excels in blending style, technology, and practicality. With its modern aesthetics, innovative water-saving technologies, durability, and ease of installation, it remains a top choice for those looking to enhance their bathroom experience. Whether for a complete remodel or a simple upgrade, the 7114 Series stands out as a trusted option in bathroom plumbing solutions.
Top Page Image Contents