Sterling Plumbing 7114 Series manual Positionner la baignoire, Position the Bath

Page 19

Position the Bath (cont.)

Verify that the bath is level and well supported by the subfloor.

If the bath is not level, shim using metal, hardwood, or other durable material. Reposition and shim the bath until it is aligned with the framing and level.

If the bath cannot be directly bonded to the subfloor or if decreased movement is desired, consider installing an optional mortar cement bed.

Install a Mortar Cement Bed (Optional)

NOTE: If a mortar cement bed will be installed, the pad is not required.

Remove the bath and pad from the alcove.

NOTE: Do not use plaster, gypsum cement, or drywall compound for this application, as they will not provide adequate structural support.

NOTE: The bath supports must rest directly on the subfloor.

Spread a 2″ (5.1 cm) layer of mortar cement on the subfloor, spreading it so that each area of the bath that will contact the subfloor has mortar cement. Do not spread the mortar cement around the drain area. Allow room for the mortar cement to expand from the weight of the bath.

Immediately move the bath into position.

Verify that the bath is level and resting on all supports.

Clean the bath to reduce the risk of damaging the surface.

Place a clean drop cloth or other similar material into the bottom and over the outside edge of the bath. Be careful not to scratch the surface of the unit.

Positionner la baignoire

ATTENTION: Risque d’endommagement du produit. Ne pas soulever ni déplacer la baignoire par le bandeau ou des montants du bandeau. Vérifier que les renforts du bandeau sont attachés avant d’installer la baignoire, puis soulever la baignoire par le rebord à des points multiples.

REMARQUE: Garder une bâche de protection en place au fond de la baignoire jusqu’à ce que la construction soit complète.

Installer les raccord du drain et du trop plein à la baignoire selon les instructions du fabricant qui accompagnent le produit.

NOTICE: Des grincements peuvent avoir lieu si la baignoire est installée sur un plancher autre que contreplaqué. Pour éviter les grincements, placer un patin entre la baignoire et le plancher et sous les supports de baignoire. Nous recommandons un patin fait en polyester filé pour jardinage ou matériau de couverture de maison. Ne pas utiliser de goudron.

NOTICE: Ne pas retirer les clips attachés à la baignoire. Les clips sont requis pour assurer une bonne installation des murs.

Positionner le patin sous les supports de la baignoire.

Positionner et ajuster la baignoire jusqu’à ce que le rebord extérieur soit égal au cadrage.

Vérifier que la baignoire soit nivelée et bien supportée par le plancher.

Dans le cas échéant, caler la baignoire en utilisant du métal, bois massif, ou autre matériau durable. Repositionner et caler la baignoire jusqu’à ce qu’elle soit alignée et nivelée avec le cadrage.

Sterling

19

1065823-2-C

Page 18 Page 20
Image 19
Page 18 Page 20
Contents 1065823-2-C Important Information Tools/Outils/Herramientas Before You Begin Thank You For Choosing SterlingMerci d’avoir choisi Sterling Gracias por elegir los productos de SterlingADA Considerations Before You BeginAvant de commencer Considérations ADA Avant de commencerAntes de comenzar Consideraciones de la ADA Antes de comenzarRoughing-In Construct the Framing Plan de raccordement Diagrama de instalaciónFraming Provisions Provisions cadrage Construire le cadrageConstruct the Framing For Above-the-Floor Drain BathsEstipulaciones para la estructura de postes de madera Construya la estructura de postes de maderaConstruire le cadrage Pour baignoires à drain au-dessus du solLevel the Subfloor Optional Prepare the SubfloorConstruya la estructura de postes de madera Para bañeras con desagüe arriba del nivel del pisoPrepare el subpiso Préparer le plancherNiveler le plancher optionnel Series/Séries 7114/Serie Series/Séries 7124/Serie Install the Rough PlumbingPrepare el subpiso Nivele el subpiso opcionalInstall the Rough Plumbing Installer la plomberie de raccordementInstale las tuberías de plomería Instale las tuberías de plomería Position the BathPositionner la baignoire Install a Mortar Cement Bed OptionalPosition the Bath Coloque la bañera Installer un lit de mortier OptionnelPositionner la baignoire Instale una capa de cemento mortero opcional Coloque la bañeraMunir les murs avoisinants Pre-Fit the Wall SurroundsMunir les murs avoisinants Ajuste inicial de las paredes circundantesAviso Instale primero la pared posterior End wall Optional AccessoriesPrepare the Wall Surrounds Prepare the Plumbing End WallCôté arrière du mur d’extrémité Accessoires optionnelsPréparer les murs avoisinants Préparer le mur d’extrémité de plomberieAccesorios opcionales Prepare las paredes circundantesBath Baignoire Bañera Secure the Wall SurroundsSecure the Wall Surrounds Sécuriser les murs avoisinantsFije las paredes circundantes Complete the InstallationComplete the Installation Compléter l’installationTermine la instalación Symptoms Probable Causes Recommended Action TroubleshootingTermine la instalación Síntomas Causas probables Acción recomendada Procedimiento para resolver problemasSymptômes Causes probables Action recommandée DépannageInstructions d’entretien et de nettoyage Care and Cleaning InstructionsInstrucciones de cuidado y limpieza WarrantyGarantía GarantieÉsta es nuestra garantía exclusiva por escrito Garantía

7114 Series specifications

The Sterling Plumbing 7114 Series is a standout line that brings together quality, functionality, and modern design to meet the needs of various bathroom styles. This series is known for its durability and practicality, making it a favored choice among homeowners and professionals alike.

One of the main features of the 7114 Series is its sleek, contemporary design. The lines are clean and minimalistic, ensuring that the products seamlessly fit into modern bathroom aesthetics. The series typically includes fixtures such as faucets, showerheads, and other essential components that not only enhance usability but also elevate the overall look of the space.

In terms of technology, the Sterling 7114 Series is equipped with innovative water-saving features that help reduce water consumption without compromising performance. These fixtures often come with aerators or flow restrictors that ensure a steady stream of water while conserving gallons per minute. This efficiency is not only beneficial for the environment but also helps reduce water bills for homeowners.

Another characteristic that sets this series apart is its ease of installation. Designed with user-friendliness in mind, many products within the 7114 Series feature straightforward mounting and connection options, making it easier for plumbers and DIY enthusiasts to install them. This accessibility has earned the 7114 Series a reputation for being a reliable choice for both new constructions and renovation projects.

Durability is also a notable feature of the Sterling Plumbing 7114 Series. Many fixtures are crafted from high-quality materials, such as solid brass and corrosion-resistant finishes, ensuring they can withstand the rigors of daily use. The finishes are often designed to resist tarnishing and scratching, allowing the products to maintain their aesthetic appeal over time.

Additionally, the Sterling 7114 Series provides a variety of options to suit individual tastes and needs. Customers can choose from different finish options, including polished chrome, brushed nickel, and more, allowing for a custom look that complements their unique bathroom design.

In conclusion, the Sterling Plumbing 7114 Series excels in blending style, technology, and practicality. With its modern aesthetics, innovative water-saving technologies, durability, and ease of installation, it remains a top choice for those looking to enhance their bathroom experience. Whether for a complete remodel or a simple upgrade, the 7114 Series stands out as a trusted option in bathroom plumbing solutions.
Top Page Image Contents