Sterling Plumbing 7104 Series Secure the Bath, Attach the Bath to the Studs, For clip attachment

Page 19

 

(1)

Bath Flange

Stud/Montant/Poste de madera

Nail

Bride de la baignoire

Reborde de la bañera

Clou

 

Clavo

 

Attachment Clip

 

Clip d'attache

 

Clip de sujeción

 

Bath/Baignoire/Bañera

(2)

Roofing Nail

Clou pour toiture

Clavo de techar

Stud

Montant mural Poste de madera

Secure the Bath

Attach the Bath to the Studs

NOTE: The bath can be attached using the clips (provided), roofing nails, or non-tapered flathead screws. Ensure the roofing nails or non-tapered flathead screws are galvanized or plated.

Verify the studs are within 1/8″ (3 mm) of the bath at the recommended clip or roofing nail locations. Shim if necessary.

For clip attachment (1):

Refer to the ″Roughing-In″ section for recommended clip locations.

At the side of the stud, position the bottom lip of the clip under the flange of the bath, as shown.

Slide the clip into place between the center of the stud and the bath. Use a pliers to bend the tab of the clip over the bath flange.

Repeat these steps for the remaining clips.

Secure the clips to the studs with roofing nails or non-tapered flathead screws. Use caution to avoid hitting the bath with a hammer.

For roofing nail or non-tapered flathead screw attachment (2):

IMPORTANT! Position the roofing nail or non-tapered flathead screw above the bath flange. Do not nail or drill through the bath flange.

Install roofing nails or flathead screws over the top of the bath flange at each stud location, as shown. This will pin the bath flange to the studs.

Sterling

19

1064912-2-A

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Series/Séries 7104/Serie 1064912-2-A Important Information Plus Tools/Outils/HerramientasMás Before You Begin Thank You For Choosing SterlingMerci d’avoir choisi Sterling Gracias por elegir los productos de SterlingBefore You Begin Avant de commencerAvant de commencer Antes de comenzarAntes de comenzar 71040122 Roughing-InRaccordement 71040112Construct the Framing Diagrama de instalaciónConstruct the Framing Construire le cadrageConstruire le cadrage Construya la estructura de postes de maderaLevel the Subfloor Prepare the SubfloorPréparer le plancher Construya la estructura de postes de maderaNivele el subpiso Prepare el subpisoPréparer le plancher Niveler le plancherInstaller la plomberie de raccordement Install the Rough PlumbingSeries 7104/Séries 7104/Serie Instale el tendido de tuberías Position the Bath Install a Mortar Cement Bed OptionalPositionner la baignoire Installer un lit de mortier OptionnelPosition the Bath Positionner la baignoire Coloque la bañeraInstale una capa de cemento mortero opcional For roofing nail or non-tapered flathead screw attachment Secure the BathAttach the Bath to the Studs For clip attachmentAttacher la baignoire aux montants Sécuriser la baignoireFije la bañera Secure the BathFije la bañera Pre-Fit the Wall Surrounds IMPORTANT! Install the back wall first¡IMPORTANTE! Instale primero la pared posterior IMPORTANT! Installer d’abord le mur arrièreMunir les murs avoisinants Ajuste inicial de las paredes circundantesAjuste inicial de las paredes circundantes Pour les baignoires avec des murs avoisinants uniquement Prepare the Wall SurroundsPréparer les murs avoisinants For Baths with Wall Surrounds OnlySólo para bañeras con paredes circundantes Accessoires optionnelsPrepare las paredes circundantes Préparer les murs avoisinantsPrepare las paredes circundantes Appliquer du mastic à la silicone Apply Silicone SealantAppliquer du mastic à la silicone Aplique sellador de siliconaNecesario Secure the Wall SurroundsFije las paredes circundantes Sécuriser les murs avoisinantsSecure the Wall Surrounds Fije las paredes circundantes Installation pour baignoire uniquement Install the Finished WallInstaller le mur fini For Bath Only InstallationsPara las instalaciones de sólo bañera Complete the InstallationInstaller le mur fini Instale la pared acabadaTermine la instalación Compléter l’installationDépannage TroubleshootingSymptoms Probable Causes Recommended Action Symptômes Causes probables Action recommandéeSíntomas Causas probables Acción recomendada Procedimiento para resolver problemasCare and Cleaning DépannageEntretien et nettoyage Care and CleaningCuidado y limpieza Years Limited Consumer/3 Years Limited Commercial WarrantyGarantie Cuidado y limpiezaGarantie Garantía1064912-2-A 1064912-2-A 1064912-2-A Phone 1-888-STERLING Mexico

7104 Series specifications

The Sterling Plumbing 7104 Series is an innovative range of bathroom fixtures designed to enhance both functionality and aesthetic appeal. Catering to modern preferences for clean lines and minimalistic design, this series includes a variety of options such as toilets, sinks, and bathtubs, each designed with the user’s comfort and convenience in mind.

A key feature of the 7104 Series is its use of high-quality materials that ensure durability and longevity. The components are made from vitreous china, known for its smooth surface and easy maintenance. This material not only resists stains and scratches but also helps to maintain cleanliness, making it an ideal choice for busy family bathrooms.

In terms of technology, the Sterling Plumbing 7104 Series integrates advanced flushing mechanisms that enhance performance while conserving water. The series often features a dual-flush option, allowing users to choose between a light flush for liquid waste and a full flush for solid waste. This not only promotes water efficiency but also aligns with contemporary eco-friendly practices, appealing to environmentally conscious consumers.

Comfort is another hallmark of the 7104 Series. Toilets feature ergonomic designs, providing optimal height and bowl shape that caters to the needs of all users. Additionally, the series’ sinks come in various styles, including undermount and pedestal options, ensuring versatile configurations to fit different bathroom layouts.

Installation and maintenance are simplified with the Sterling Plumbing 7104 Series. The products are designed for straightforward installation, with clear instructions and essential mounting hardware included. Moreover, the fixtures are engineered to minimize the need for repairs, thereby reducing long-term maintenance efforts for homeowners.

Overall, the Sterling Plumbing 7104 Series stands out in the market for its combination of style, efficiency, and practicality. With an emphasis on user experience, it incorporates modern technologies and materials that not only look great but also function exceptionally well, making it a worthwhile investment for any bathroom renovation or new build project.
Top Page Image Contents