Sterling Plumbing 7104 Series manual Secure the Wall Surrounds, Necesario

Page 30

Stud/Montant/Poste de madera

Shim if necessary.

 

Wall Flange

Caler si nécessaire.

Utilice cuñas de ser

Bride du mur

Reborde de la pared

necesario.

Bath Flange

Bride de la baignoire

Reborde de la bañera

Wall Surround Mur avoisinant Paredes circundantes

1/32" (1 mm)

Bath

Baignoire

Bañera

Roofing Nail or Flathead Screw Clous pour toiture ou vis à tête plate Clavo de techar o tornillo de cabeza plana

Secure the Wall Surrounds

Remove the temporary roofing nail from the back wall.

CAUTION: Risk of property damage. Wall surrounds must rest within 1/32″ (1 mm) (the thickness of a credit card) from the bath rim to ensure proper water

management and to prevent leakage.

Ensure that the wall surrounds are properly secured and seated on the bath. The front edges of the end walls must be flush with the front edge of the bath. If a gap exists, pull the end walls slightly forward.

CAUTION: Risk of product or property damage. If using non-tapered flathead screws rather than roofing nails, do not overtighten the screws. Excessive

tightening can damage the wall flange.

Starting from the bottom of the end walls and working up, secure the end walls to the studs approximately every 12″ (30.5 cm). If roofing nails are used, nail through the dimples on the wall flanges. If using non-tapered flathead screws, drill through the dimples on the wall flanges. Do not overtighten the non-tapered flathead screws.

NOTE: Leave a 1/8″ (3 mm) gap between the edge of the wall surround and the finished wall material. When sealed, this gap will reduce the possibility of water seeping into the wall material.

Ensure fiber or other soft insulation does not drop down into the water channel. Cover or seal any loose material. Failure to do so may cause wicking of water from the water channel into the insulation which may induce mold, leakage, or mildew. Ensure the channels are free of debris after installation.

Secure the wall flanges across the top of the wall surrounds at every stud location. Add shims if necessary to bring the studs into contact with the bath flange.

1064912-2-A

30

Sterling

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Series/Séries 7104/Serie 1064912-2-A Important Information Tools/Outils/Herramientas PlusMás Gracias por elegir los productos de Sterling Thank You For Choosing SterlingMerci d’avoir choisi Sterling Before You BeginAvant de commencer Before You BeginAntes de comenzar Avant de commencerAntes de comenzar 71040112 Roughing-InRaccordement 71040122Diagrama de instalación Construct the FramingConstruire le cadrage Construct the FramingConstruya la estructura de postes de madera Construire le cadrageConstruya la estructura de postes de madera Prepare the SubfloorPréparer le plancher Level the SubfloorNiveler le plancher Prepare el subpisoPréparer le plancher Nivele el subpisoInstall the Rough Plumbing Installer la plomberie de raccordementSeries 7104/Séries 7104/Serie Instale el tendido de tuberías Install a Mortar Cement Bed Optional Position the BathInstaller un lit de mortier Optionnel Positionner la baignoirePosition the Bath Coloque la bañera Positionner la baignoireInstale una capa de cemento mortero opcional For clip attachment Secure the BathAttach the Bath to the Studs For roofing nail or non-tapered flathead screw attachmentSecure the Bath Sécuriser la baignoireFije la bañera Attacher la baignoire aux montantsFije la bañera IMPORTANT! Install the back wall first Pre-Fit the Wall SurroundsAjuste inicial de las paredes circundantes IMPORTANT! Installer d’abord le mur arrièreMunir les murs avoisinants ¡IMPORTANTE! Instale primero la pared posteriorAjuste inicial de las paredes circundantes For Baths with Wall Surrounds Only Prepare the Wall SurroundsPréparer les murs avoisinants Pour les baignoires avec des murs avoisinants uniquementPréparer les murs avoisinants Accessoires optionnelsPrepare las paredes circundantes Sólo para bañeras con paredes circundantesPrepare las paredes circundantes Apply Silicone Sealant Appliquer du mastic à la siliconeAplique sellador de silicona Appliquer du mastic à la siliconeSecure the Wall Surrounds NecesarioSécuriser les murs avoisinants Fije las paredes circundantesSecure the Wall Surrounds Fije las paredes circundantes For Bath Only Installations Install the Finished WallInstaller le mur fini Installation pour baignoire uniquementInstale la pared acabada Complete the InstallationInstaller le mur fini Para las instalaciones de sólo bañeraCompléter l’installation Termine la instalaciónSymptômes Causes probables Action recommandée TroubleshootingSymptoms Probable Causes Recommended Action DépannageDépannage Procedimiento para resolver problemasCare and Cleaning Síntomas Causas probables Acción recomendadaCare and Cleaning Entretien et nettoyageCuidado y limpieza Cuidado y limpieza WarrantyGarantie Years Limited Consumer/3 Years Limited CommercialGarantía Garantie1064912-2-A 1064912-2-A 1064912-2-A Phone 1-888-STERLING Mexico

7104 Series specifications

The Sterling Plumbing 7104 Series is an innovative range of bathroom fixtures designed to enhance both functionality and aesthetic appeal. Catering to modern preferences for clean lines and minimalistic design, this series includes a variety of options such as toilets, sinks, and bathtubs, each designed with the user’s comfort and convenience in mind.

A key feature of the 7104 Series is its use of high-quality materials that ensure durability and longevity. The components are made from vitreous china, known for its smooth surface and easy maintenance. This material not only resists stains and scratches but also helps to maintain cleanliness, making it an ideal choice for busy family bathrooms.

In terms of technology, the Sterling Plumbing 7104 Series integrates advanced flushing mechanisms that enhance performance while conserving water. The series often features a dual-flush option, allowing users to choose between a light flush for liquid waste and a full flush for solid waste. This not only promotes water efficiency but also aligns with contemporary eco-friendly practices, appealing to environmentally conscious consumers.

Comfort is another hallmark of the 7104 Series. Toilets feature ergonomic designs, providing optimal height and bowl shape that caters to the needs of all users. Additionally, the series’ sinks come in various styles, including undermount and pedestal options, ensuring versatile configurations to fit different bathroom layouts.

Installation and maintenance are simplified with the Sterling Plumbing 7104 Series. The products are designed for straightforward installation, with clear instructions and essential mounting hardware included. Moreover, the fixtures are engineered to minimize the need for repairs, thereby reducing long-term maintenance efforts for homeowners.

Overall, the Sterling Plumbing 7104 Series stands out in the market for its combination of style, efficiency, and practicality. With an emphasis on user experience, it incorporates modern technologies and materials that not only look great but also function exceptionally well, making it a worthwhile investment for any bathroom renovation or new build project.
Top Page Image Contents