Stanley Black & Decker CH2 owner manual Operating Guidelines, YOU Proceed ANY Further

Page 11

Operating Guidelines

READ THESE OPERATING GUIDELINES BEFORE

YOU PROCEED ANY FURTHER

1.Do not put hands and feet near rotating parts or in the feeding chambers and discharge opening. Contact with the rotating impeller can amputate fingers, hands, and feet.

2.Before starting the machine, make sure the chipper chute, feed intake, and cutting chamber are empty and free of all debris.

3.Thoroughly inspect all material to be shredded and remove any metal, rocks, bottles, cans, or other foreign objects which could cause personal injury or damage to the machine.

4.If it becomes necessary to push material through the shredder hopper, use a small diameter stick. Do not use your hands or feet.

5.If the impeller strikes a foreign object or if your machine should start making an unusual noise or vibration, immediately shut the engine off. Allow the impeller to come to a complete stop.

Disconnect the spark plug wire, ground it against the engine and perform the following steps:

a.Inspect for damage.

b.Repair or replace any damaged parts.

c.Check for any loose parts and tighten to assure continued safe operation.

6.Do not allow an accumulation of processed material to build up in the discharge area. This can prevent proper discharge and result in kickback of material through the feed opening.

7.Do not attempt to shred or chip material larger than specified on the machine or in this manual. Personal injury or machine damage could result.

The funnel on the chipper/ shredder is for leaves only. Do not use the funnel for vines, wet vegetation, or long branches such as Weeping Willows as they may clog the cutting chamber.

The side chute is for longer and/or thicker pieces of yard waste.

Depending on your mod- el, you may chip to your models capacity (page 2).

8.Never attempt to unclog either the feed intake or discharge opening while the engine is running. Shut the engine off, wait until all moving parts have stopped, disconnect the spark plug wire and ground it against the engine before clearing debris.

9.Never operate without the leaf funnel, limb chute, or discharge chute properly attached to the machine. Stop the engine when leaving the operating position.

10.Keep all guards, deflectors and safety devices in place and operating properly.

11.Keep your face and body back and to the side of the chipper chute while feeding material into the machine to avoid accidental kickback injuries.

12.Never operate this machine without good visibility or light.

13.Do not operate on a non-level surface.

14.Do not operate in a confined space.

15.Do not operate this machine while under the influence of alcohol or drugs.

16.Muffler and engine become hot and can cause a burn. Do not touch.

17.Never pick up or carry machine while the engine is running.

18.Do not leave this machine running while unattended

19.Keep children, bystanders, and pets 75 feet away.

20.Use only manufacturer approved accessories/attachments.

 

STANLEY is a registered trademark of The Stanley Works or its affiliates and are used under license by GXi Outdoor Power LLC.

 

No part of this publication can be printed or copied without written permission.

Rev2.5-15-12

8

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Location of Purchase Chipper/Shredder with 2-Way FeedRemain with the chipper/shredder if resold Contents Carbon Monoxide GAS Model # TrainingComponent Identification Comments Missing Parts Request FormPlease indicate the part that you are missing Component Identification Description Stanley CH2 Chipper Shredder Spare Parts DiagramStanley CH7 Chipper Shredder Spare Parts Diagram Your Responsibility Safety InformationSafety Label Locations Safety Information Operator ResponsibilityYOU Proceed ANY Further Operating GuidelinesVerify all parts are in the hardware bag Figure AssemblyRemove the chipper from its carton Remove the shipping frame item 6 from item 1 aboveLeaf funnel with entry shield Re-connect the spark plug wire Add oil and fuelAttaching the chipper discharge chute Figure Attaching the lower leaf funnel section. FigureFire and Burn Hazards Important Engine InformationEmission Control System Information Carbon Monoxide GasAdd gasoline Using the Chipper ShredderOperating Instructions Starting the EngineMaintenance and Storage Removing and Sharpening the Limb Chute Blades Storing the Chipper/Shredder Cleaning the Chipper/ShredderRemoving and replacing the flail hammers To Change the OilProblem Cause Remedy TroubleshootingEngine Months Limited Warranty and Service

CH2 specifications

Stanley Black & Decker CH2 is a groundbreaking product that has carved a niche for itself within the tool and construction industry. This advanced tool is crafted for professionals seeking efficiency and unparalleled performance in their projects. At the heart of the CH2's design is its commitment to high-quality engineering and user-focused features, making it an ideal choice for contractors and DIY enthusiasts alike.

One of the standout features of the Stanley Black & Decker CH2 is its dual-mode functionality, allowing users to toggle between various modes tailored for different applications. This versatility enhances productivity, making it a multipurpose tool that can handle everything from drilling to fastening tasks with ease. The CH2 is equipped with a powerful brushless motor that not only ensures longer operational life but also optimizes energy consumption and performance.

Another technological advancement found in the CH2 is its advanced electronic feedback system. This technology enables real-time monitoring of the tool's performance, ensuring that it maintains consistent torque and prevents overload situations. This leads to improved accuracy in tasks and enhances the overall safety of users.

The Stanley Black & Decker CH2 also incorporates an ergonomic design, featuring a lightweight construction that minimizes fatigue during extended use. The handle is perfectly contoured to fit comfortably in the user's grip, and the additional rubberized grip provides enhanced control, thereby reducing the risk of slips or drops.

For maximum efficiency, the CH2 includes an integrated LED work light that illuminates work surfaces, a feature that is especially useful in low-light conditions. This thoughtful inclusion allows users to maintain visibility and precision, ensuring that every task is completed to the highest standard.

Moreover, compatibility with Stanley Black & Decker’s extensive range of accessories and batteries allows users to seamlessly transition between different tasks without the hassle of changing tools or recharging batteries frequently. The CH2 stands as a testament to Stanley Black & Decker's commitment to innovation, clarity, and user convenience.

Overall, the Stanley Black & Decker CH2 represents a leap forward in tool technology, combining state-of-the-art features with the reliability that professionals have come to expect from the brand. Whether you are on a construction site or tackling a home improvement project, the CH2 is designed to meet diverse demands with power and precision, making it an invaluable addition to any toolkit.
Top Page Image Contents