Stanley Black & Decker CH2 Removing and replacing the flail hammers, Cleaning the Chipper/Shredder

Page 18

Maintenance and Storage

Always stop engine, disconnect spark plug, and ground against engine before cleaning, lubricating or doing any kind of maintenance on your machine.

Removing and Sharpening the Leaf Funnel Blade

1.Disconnect the spark plug wire and ground against the engine.

2.Remove the lower section and upper section of the funnel as a subassembly. This is done by removing three bolts with the 13mm wrenches provided in the hardware bag.

3.Remove the two blade bolts using an Allen wrench provided in the hardware bag. It may be necessary to use a block of wood to prevent the rotor from turning while loosening and retightening the blade bolts.

Make certain the block of wood is removed before reassembly of the funnel.

4.Replace or sharpen the blade.

∙ When sharpening the blade, protect hands by using gloves and following the original angle of grind.Torque to 21-25 Ft lbs.

∙ When reinstalling the blade note the orientation. The top of the blade will have the cutting edge to the left and the bottom edge to the right.

Removing and replacing the flail hammers

∙ Disconnect the spark plug wire and ground against the engine. ∙ Remove the leaf funnel and limb chute.

∙ Remove the retainer clip for the flail hammer pin. Use a piece of pipe or wood to block the flails, preventing them from inadvertently turning.

∙ Remove the flail hammer pin through the limb chute opening. ∙ Replace the flail hammer, flail hammer pin and retaining clip.

Cleaning the Chipper/Shredder

∙ Make sure engine is off.

∙ Wipe off machine with an oiled rag to prevent rust. ∙ If the fuel tank has to be drained, do so outdoors.

∙ Observe proper disposal laws and regulations for gas, oil, etc., to protect the environment.

To Change the Oil

∙ Move the unit to flat ground.

∙ Remove spark plug and ground it to the engine block. ∙ Place an oil collection pan under the unit.

∙ Remove one of the 10mm oil drain plugs.( located on the bottom center of the engine behind the wheel)

∙ Allow oil to drain completely. ∙ Reinstall the oil drain plug

∙ Add new 10W-30 oil. See page 2 for oil capacity. ∙ Reinstall the spark plug.

∙ Please dispose of used motor responsibly and according to local regulations.

Storing the Chipper/Shredder

∙ Clean the equipment thoroughly.

∙ Wipe equipment with an oiled rag to prevent rust.

∙ Refer to engine manual for correct engine storage instructions. ∙ Store unit in a clean, dry area. Do not store next to corrosive

materials such as fertilizer.

∙ Never store the machine or fuel container inside where there is an open flame, spark or pilot light such as a water heater, furnace, clothes dryer, etc.

 

STANLEY is a registered trademark of The Stanley Works or its affiliates and are used under license by GXi Outdoor Power LLC.

 

No part of this publication can be printed or copied without written permission.

Rev2.5-15-12

15

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Chipper/Shredder with 2-Way Feed Location of PurchaseRemain with the chipper/shredder if resold Contents Carbon Monoxide GAS Training Model #Component Identification Missing Parts Request Form Please indicate the part that you are missingComments Component Identification Stanley CH2 Chipper Shredder Spare Parts Diagram Stanley CH7 Chipper Shredder Spare Parts DiagramDescription Safety Information Operator Responsibility Safety InformationSafety Label Locations Your ResponsibilityOperating Guidelines YOU Proceed ANY FurtherRemove the shipping frame item 6 from item 1 above AssemblyRemove the chipper from its carton Verify all parts are in the hardware bag FigureAttaching the lower leaf funnel section. Figure Re-connect the spark plug wire Add oil and fuelAttaching the chipper discharge chute Figure Leaf funnel with entry shieldCarbon Monoxide Gas Important Engine InformationEmission Control System Information Fire and Burn HazardsStarting the Engine Using the Chipper ShredderOperating Instructions Add gasolineMaintenance and Storage Removing and Sharpening the Limb Chute Blades To Change the Oil Cleaning the Chipper/ShredderRemoving and replacing the flail hammers Storing the Chipper/ShredderTroubleshooting Problem Cause RemedyLimited Warranty and Service Engine Months

CH2 specifications

Stanley Black & Decker CH2 is a groundbreaking product that has carved a niche for itself within the tool and construction industry. This advanced tool is crafted for professionals seeking efficiency and unparalleled performance in their projects. At the heart of the CH2's design is its commitment to high-quality engineering and user-focused features, making it an ideal choice for contractors and DIY enthusiasts alike.

One of the standout features of the Stanley Black & Decker CH2 is its dual-mode functionality, allowing users to toggle between various modes tailored for different applications. This versatility enhances productivity, making it a multipurpose tool that can handle everything from drilling to fastening tasks with ease. The CH2 is equipped with a powerful brushless motor that not only ensures longer operational life but also optimizes energy consumption and performance.

Another technological advancement found in the CH2 is its advanced electronic feedback system. This technology enables real-time monitoring of the tool's performance, ensuring that it maintains consistent torque and prevents overload situations. This leads to improved accuracy in tasks and enhances the overall safety of users.

The Stanley Black & Decker CH2 also incorporates an ergonomic design, featuring a lightweight construction that minimizes fatigue during extended use. The handle is perfectly contoured to fit comfortably in the user's grip, and the additional rubberized grip provides enhanced control, thereby reducing the risk of slips or drops.

For maximum efficiency, the CH2 includes an integrated LED work light that illuminates work surfaces, a feature that is especially useful in low-light conditions. This thoughtful inclusion allows users to maintain visibility and precision, ensuring that every task is completed to the highest standard.

Moreover, compatibility with Stanley Black & Decker’s extensive range of accessories and batteries allows users to seamlessly transition between different tasks without the hassle of changing tools or recharging batteries frequently. The CH2 stands as a testament to Stanley Black & Decker's commitment to innovation, clarity, and user convenience.

Overall, the Stanley Black & Decker CH2 represents a leap forward in tool technology, combining state-of-the-art features with the reliability that professionals have come to expect from the brand. Whether you are on a construction site or tackling a home improvement project, the CH2 is designed to meet diverse demands with power and precision, making it an invaluable addition to any toolkit.
Top Page Image Contents