Stanley Black & Decker CH2 owner manual Troubleshooting, Problem Cause Remedy

Page 19

Troubleshooting

Problem

 

Cause

 

Remedy

 

 

 

 

 

 

 

 

 

Engine fails to start

 

1.

Spark plug wire disconnected.

 

1.

Connect wire to spark plug.

 

 

 

2.

Fuel tank empty or stale fuel.

 

2.

Fill tank with clean, fresh gasoline.

 

 

 

3.

Throttle control lever not in correct starting

3.

Move throttle lever to FAST position.

 

 

 

 

position. (If equipped)

 

 

 

 

 

 

4.

Choke not in CHOKE position. (If equipped)

4.

Move choke to CHOKE position.

.

 

 

5.

Engine not primed.

 

5.

Prime engine.

 

 

 

6.

Blocked fuel line.

 

6.

Clean fuel line.

 

 

 

7.

Faulty spark plug.

 

7.

Clean, adjust gap, or replace.

 

 

 

8.

Low oil

 

8.

Fill

 

 

 

 

 

 

Call GXi Parts & Service (919)-550-3259

 

 

 

 

 

 

 

 

 

Engine runs erratic

 

1.

Spark plug wire loose.

 

1.

Connect and tighten spark plug wire.

 

 

 

2.

Unit running on CHOKE. (If equipped)

 

2.

Move choke lever to OFF position.

 

 

 

3.

Blocked fuel line or stale fuel.

.

3.

Clean fuel line; fill tank with clean, fresh gasoline.

 

 

4.

Water or dirt in fuel system.

 

4.

Drain fuel tank. Refill with fresh fuel.

 

 

 

5.

Dirty air cleaner.

 

5.

Clean or replace air cleaner.

 

 

 

6.

Carburetor out of adjustment.

 

6.

Call GXi Parts & Service (919)-550-3259

 

 

 

 

 

 

 

 

 

Too much vibration

 

1.

Loose parts or damaged carousel .

 

1.

Call GXi Parts & Service (919)-550-3259

 

 

 

 

 

 

 

 

 

Engine overheats

 

1.

Engine oil level low.

 

1.

Fill crankcase with proper oil.

 

 

 

2.

Dirty air cleaner.

 

2.

Clean or replace air cleaner.

 

 

 

3.

Carburetor not adjusted properly.

 

3.

Call GXi Parts & Service (919)-550-3259

 

 

 

 

 

 

 

 

 

Occasional skip (hesitates)

 

1.

Spark plug gap too close.

 

1.

Adjust gap to.030”.

 

 

 

 

 

 

Call GXi Parts & Service (919)-550-3259

 

 

 

 

 

 

 

 

Unit does not discharge

 

1.

Discharge chute clogged.

.

1.

Stop engine immediately and disconnect spark

 

 

 

.

 

 

plug wire. Clean flail screen and inside of

 

 

2.

Foreign object lodged in carousel.

.

 

discharge opening.

 

 

 

3.

Low engine RPM.

 

2.

Stop engine and disconnect spark plug wire.

 

 

 

 

 

 

Remove lodged object.

 

 

 

 

 

 

3.

Always run engine at full throttle.

 

 

 

 

 

 

Call GXi Parts & Service (919)-550-3259

 

 

 

 

 

 

 

 

 

Rate of discharge slows

 

1.

Low engine RPM.

 

1.

Always run engine at full throttle

 

 

 

2.

Chipper blades are dull.

 

2.

Replace chipper blades or see your authorized

 

 

 

 

 

 

service dealer.

 

 

 

 

 

 

Call GXi Parts & Service (919)-550-3259

 

 

 

 

 

NOTE: For repairs beyond the minor adjustments listed above, contact GXi Parts and Service (919)-550-3259 for support over

 

the phone or getting setup with your nearest authorized service dealer.

 

 

 

 

STANLEY is a registered trademark of The Stanley Works or its affiliates and are used under license by GXi Outdoor Power LLC.

 

 

 

 

No part of this publication can be printed or copied without written permission.

 

Rev2.5-15-12

 

 

16

 

 

 

 

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Location of Purchase Chipper/Shredder with 2-Way FeedRemain with the chipper/shredder if resold Contents Carbon Monoxide GAS Model # TrainingComponent Identification Please indicate the part that you are missing Missing Parts Request FormComments Component Identification Stanley CH7 Chipper Shredder Spare Parts Diagram Stanley CH2 Chipper Shredder Spare Parts DiagramDescription Your Responsibility Safety InformationSafety Label Locations Safety Information Operator ResponsibilityYOU Proceed ANY Further Operating GuidelinesVerify all parts are in the hardware bag Figure AssemblyRemove the chipper from its carton Remove the shipping frame item 6 from item 1 aboveLeaf funnel with entry shield Re-connect the spark plug wire Add oil and fuelAttaching the chipper discharge chute Figure Attaching the lower leaf funnel section. FigureFire and Burn Hazards Important Engine InformationEmission Control System Information Carbon Monoxide GasAdd gasoline Using the Chipper ShredderOperating Instructions Starting the EngineMaintenance and Storage Removing and Sharpening the Limb Chute Blades Storing the Chipper/Shredder Cleaning the Chipper/ShredderRemoving and replacing the flail hammers To Change the OilProblem Cause Remedy TroubleshootingEngine Months Limited Warranty and Service

CH2 specifications

Stanley Black & Decker CH2 is a groundbreaking product that has carved a niche for itself within the tool and construction industry. This advanced tool is crafted for professionals seeking efficiency and unparalleled performance in their projects. At the heart of the CH2's design is its commitment to high-quality engineering and user-focused features, making it an ideal choice for contractors and DIY enthusiasts alike.

One of the standout features of the Stanley Black & Decker CH2 is its dual-mode functionality, allowing users to toggle between various modes tailored for different applications. This versatility enhances productivity, making it a multipurpose tool that can handle everything from drilling to fastening tasks with ease. The CH2 is equipped with a powerful brushless motor that not only ensures longer operational life but also optimizes energy consumption and performance.

Another technological advancement found in the CH2 is its advanced electronic feedback system. This technology enables real-time monitoring of the tool's performance, ensuring that it maintains consistent torque and prevents overload situations. This leads to improved accuracy in tasks and enhances the overall safety of users.

The Stanley Black & Decker CH2 also incorporates an ergonomic design, featuring a lightweight construction that minimizes fatigue during extended use. The handle is perfectly contoured to fit comfortably in the user's grip, and the additional rubberized grip provides enhanced control, thereby reducing the risk of slips or drops.

For maximum efficiency, the CH2 includes an integrated LED work light that illuminates work surfaces, a feature that is especially useful in low-light conditions. This thoughtful inclusion allows users to maintain visibility and precision, ensuring that every task is completed to the highest standard.

Moreover, compatibility with Stanley Black & Decker’s extensive range of accessories and batteries allows users to seamlessly transition between different tasks without the hassle of changing tools or recharging batteries frequently. The CH2 stands as a testament to Stanley Black & Decker's commitment to innovation, clarity, and user convenience.

Overall, the Stanley Black & Decker CH2 represents a leap forward in tool technology, combining state-of-the-art features with the reliability that professionals have come to expect from the brand. Whether you are on a construction site or tackling a home improvement project, the CH2 is designed to meet diverse demands with power and precision, making it an invaluable addition to any toolkit.
Top Page Image Contents