Shindaiwa T230 manual Troubleshooting Guide, Possible Cause

Page 20

Troubleshooting Guide

ENGINE DOES NOT START

What To Check

Does the engine crank?

YES

Good compression?

YES

NO

NO

Possible Cause

Faulty recoil starter.

Fluid in the crankcase.

Internal damage.

Loose spark plug.

Excess wear on cylinder, piston, rings.

Remedy

Consult with an authorized servicing dealer.

Tighten and re-test.

Consult with an authorized servicing dealer.

Does the tank contain fresh fuel of the proper grade?

YES

Is fuel visible and moving in the return line when priming?

YES

Is there spark at the spark plug wire terminal?

YES

Check the spark plug.

NO

NO

NO

Fuel incorrect, stale, or contaminated; mixture incorrect.

Check for clogged fuel filter and/or vent.

The ignition switch is in “O” (OFF) position. Shorted ignition ground.

Faulty ignition unit.

If the plug is wet, excess fuel may be in the cylinder.

The plug is fouled or improperly gapped.

The plug is damaged internally or of the wrong size.

Refill with fresh, clean unleaded gasoline with a pump octane of 87 or higher, mixed with Shindaiwa Premium 2-cycle mixing oil at a 50:1 gasoline/oil ratio.

Replace fuel filter or vent as required. Restart.

Move switch to “I” (ON) position and re-start.

Consult with an authorized servicing dealer.

Crank the engine with the plug removed, reinstall the plug, and restart.

Clean and regap the plug to 0.024” (0.6 mm). Restart.

Replace the plug with a Champion CJ8 or equivalent type spark plug of the correct heat range. For EMC compliance, use NGK BMR6A. Restart.

 

 

 

 

 

 

 

 

 

 

 

LOW POWER OUTPUT

 

 

What To Check

 

 

 

Possible Cause

 

Remedy

 

 

 

 

Operator is overworking the unit.

 

Shorten trimmer line. Cut at a slower rate.

Is the engine overheating?

 

 

 

 

 

 

 

Carburetor mixture is too lean.

 

Consult with an authorized servicing dealer.

 

 

 

 

 

 

 

 

 

 

 

 

 

Improper fuel ratio.

 

Refill with fresh, clean unleaded gasoline with

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

a pump octane of 87 or higher, mixed with

 

 

 

 

 

 

Shindaiwa Premium 2-cycle mixing oil at a 50:1

 

 

 

 

Fan, fan cover, cylinder fins dirty or damaged.

 

gasoline/oil ratio

 

 

 

 

 

 

 

 

 

 

Consult with an authorized servicing dealer.

 

 

 

 

 

 

Carbon deposits on the piston or in the muffler.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Clogged air filter.

 

Clean or replace the air filter.

Engine is rough at all speeds.

 

 

 

 

 

 

 

 

May also have black smoke and/

 

 

 

Loose or damaged spark plug.

 

Tighten or replace the plug with a Champion CJ8 or

 

 

 

 

or unburned fuel at the exhaust.

 

 

 

 

 

equivalent type spark plug of the correct heat range.

 

 

 

 

 

 

For EMC compliance, use NGK BMR6A. Restart.

 

 

 

 

 

 

 

 

 

 

Air leakage or clogged fuel line.

 

Repair or replace fuel filter and/or fuel line.

 

 

 

 

 

 

 

 

 

Water in the fuel.

 

Refill with fresh fuel/oil mixture. See page 11.

 

 

 

 

 

 

 

 

 

Piston seizure.

 

Consult with an authorized servicing dealer.

 

 

 

 

 

 

 

 

 

Faulty carburetor and/or diaphragm.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Overheating condition.

 

See above.

Engine is knocking.

 

 

 

 

 

 

 

Improper fuel.

 

Check fuel octane rating; check for presence of

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

alcohol in the fuel (page 11). Refuel as necessary.

 

 

 

 

 

 

 

 

 

 

Carbon deposits in the combustion chamber.

 

Consult with an authorized servicing dealer.

 

 

 

 

 

 

 

 

 

 

 

 

20

Image 20
Contents T230 Grass Trimmer T230X Grass Trimmer C230 Brushcutter Introduction ContentsGeneral Safety Instructions Minimize the Risk of Fire General Safety Instructions The Properly Equipped OperatorStay Alert Safety Labels Be Aware of the Working Environment all unitsUnit Description SpecificationsPrior to Assembly Assembly Driveshaft/Powerhead All Models Assembly HandleAssembly Handlebar C230 Assembly Throttle Linkage and Ignition Leads All ModelsAssemble the Handlebar Remove the Cylinder CoverAssemble and Adjust Throttle Cable Sub-Shield T230X and C230 To Change Position Line CutterAssembly Trimmer Head C230/T230/T230X Assembly Blade C230/T230XInstall the Trimmer Head Mount the BladeExamples of 501 mixing quantities Mixing FuelFilling the Fuel Tank Stopping the Engine When the Engine StartsStarting the Engine Shoulder Strap Adjusting Engine IdleChecking Unit Condition Using a Grass Trimmer T230 Engine Operating SpeedsTrimming and Mowing Grass EdgingUsing a Brushcutter Blade C230/T230X Blade ThrustBrushcutter Handlebar Brushcutter HarnessHour Maintenance General MaintenanceDaily Maintenance 10/15-Hour Maintenance Every 50 hours of operation23055 Long Term Storage Blade SharpeningMultiple-tooth Circular Blade Shindaiwa Tornado BladeTroubleshooting Guide Possible CauseSymptom Possible Cause Remedy Manufacturers Warranty Coverage
Related manuals
Manual 20 pages 29.68 Kb