Shindaiwa manual Sub-Shield T230X and C230, To Change Position Line Cutter

Page 9

Assembly

Cutting Attachment Shield All Models

Socket-Head

 

 

T230

 

T230X/C230

Cap Screw

 

 

Bolt

 

Outer

 

 

 

 

 

Tube

 

Cutting

 

Upper Clamp

 

 

 

 

 

Bracket

 

 

Attachment

 

 

 

 

 

Shield

 

 

Shim

 

 

 

Shim

 

 

 

 

 

 

Clamp Screw

 

 

Nuts

 

 

 

 

 

 

 

 

 

Line Cutter

 

Shim

 

 

 

 

 

Shim

 

 

Nut

 

 

 

 

 

 

Retaining

Cutting

 

 

 

 

Attachment Shield

 

 

Cutting Attachment Shield

Nut

 

 

Mounting Plate

 

Hex

 

Figure 14A

 

 

Figure 14

 

Screws

 

 

 

 

 

 

Install the Cutting Attachment Shield T230/T230X/C230.

1.Insert the cutting attachment shield between the outer tube and the cutting attachment shield mounting plate. See Figure 14.

NOTE:

It may be necessary to loosen the retaining nut and clamp screw to adjust cutting attach- ment shield mounting plate.

2.Fit the two shims and the bracket over the outer tube and loosely install the four socket-head cap screws. See Figure 14.

3.Tighten the four socket-head cap screws to secure the cutting attachment shield.

CAUTION!

Make sure the clamp screw and retaining nut are securely tightened before tighten­ ing the four socket-head cap screws.

WARNING!

NEVER operate the unit without the cutting attachment shield installed and tightly secured!

Sub-Shield T230X and C230.

(when trimmer head is in use)

1.Attach the shield extension to the cutting attachment shield.

WARNING!

NEVER use this machine without sub- shield when using a trimmer head.

Cutting Attachment Shield

Hook

Receiver

Sub-shield

Hook

 

Figure 15

CAUTION!

Make sure the sub-guard is completely hooked at the hook receiver.

To Change Position of

Line Cutter.

The line cutter can be positioned in

2 positions to obtain different line length for cutting.

1.Remove the 2 hex screws with a 4 mm hex wrench. See Figure 14A.

2.Rotate line cutter. See Figure 14A.

3.Reinstall the two hex screws and tighten them securely.

WARNING!

The line cutter is very sharp. Wear gloves to protect your hands when handling.

NOTE:

Be careful to not lose the 2 nuts in the cutting attachment shield, they are not captured.

Image 9
Contents T230 Grass Trimmer T230X Grass Trimmer C230 Brushcutter Contents General Safety InstructionsIntroduction General Safety Instructions The Properly Equipped Operator Stay AlertMinimize the Risk of Fire Be Aware of the Working Environment all units Safety LabelsSpecifications Prior to AssemblyUnit Description Assembly Handle Assembly Driveshaft/Powerhead All ModelsAssembly Throttle Linkage and Ignition Leads All Models Assembly Handlebar C230Assemble the Handlebar Remove the Cylinder CoverAssemble and Adjust Throttle Cable To Change Position Line Cutter Sub-Shield T230X and C230Assembly Blade C230/T230X Assembly Trimmer Head C230/T230/T230XInstall the Trimmer Head Mount the BladeMixing Fuel Filling the Fuel TankExamples of 501 mixing quantities When the Engine Starts Starting the EngineStopping the Engine Adjusting Engine Idle Checking Unit ConditionShoulder Strap Engine Operating Speeds Using a Grass Trimmer T230Trimming and Mowing Grass EdgingBlade Thrust Using a Brushcutter Blade C230/T230XBrushcutter Handlebar Brushcutter HarnessGeneral Maintenance Daily MaintenanceHour Maintenance Every 50 hours of operation 10/15-Hour Maintenance23055 Blade Sharpening Long Term StorageMultiple-tooth Circular Blade Shindaiwa Tornado BladePossible Cause Troubleshooting GuideSymptom Possible Cause Remedy Manufacturers Warranty Coverage
Related manuals
Manual 20 pages 29.68 Kb