Shindaiwa LE261/EVC manual Troubleshooting Guide, Possible Cause

Page 15

Troubleshooting Guide

ENGINE DOES NOT START

What To Check

Does the engine crank?

YES

Good compression?

YES

NO

NO

Possible Cause

Faulty recoil starter.

Fluid in the crankcase.

Internal damage.

Loose spark plug.

Excess wear on cylinder, piston, rings.

Remedy

Consult with an authorized servicing dealer.

Tighten and re-test.

Consult with an authorized servicing dealer.

Does the tank contain fresh fuel of the proper grade?

YES

Is fuel visible and moving in the return line when priming?

YES

Is there spark at the spark plug wire terminal?

YES

Check the spark plug.

NO

NO

NO

Fuel incorrect, stale, or contaminated; mixture incorrect.

Check for clogged fuel filter and/or vent.

The ignition switch is in “O” (OFF) position. Shorted ignition ground.

Faulty ignition unit.

If the plug is wet, excess fuel may be in the cylinder.

The plug is fouled or improperly gapped.

The plug is damaged internally or of the wrong size.

Refill with fresh, clean unleaded gasoline with a pump octane of 87 or higher mixed with a 2-cycle air cooled mixing oil that meets or exceeds ISO-L-EGD and/or JASO FC classified oils at 50:1 gasoline/oil ratio.

Clean as required; restart.

Move switch to “I” (ON) position and re-start.

Consult with an authorized servicing dealer.

Crank the engine with the plug removed, reinstall the plug, and restart.

Clean and regap the plug to 0.024” (0.6 - 0.7 mm). Restart.

Replace the plug with a Champion CJ8Y or equivalent type spark plug of the correct heat range. Restart.

 

 

 

 

 

 

 

 

 

 

 

LOW POWER OUTPUT

 

 

What To Check

 

 

 

Possible Cause

 

Remedy

 

 

 

 

Operator is overworking the unit.

 

Shorten trimmer line. Cut at a slower rate.

Is the engine overheating?

 

 

 

 

 

 

 

Carburetor mixture is too lean.

 

Consult with an authorized servicing dealer.

 

 

 

 

 

 

 

 

 

 

 

 

 

Improper fuel ratio.

 

Refill with fresh, clean unleaded gasoline with a pump

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

octane of 87 or higher mixed with a 2-cycle air cooled

 

 

 

 

 

 

mixing oil that meets or exceeds ISO-L-EGD and/or

 

 

 

 

Fan, fan cover, cylinder fins dirty or damaged.

 

JASO FC classified oils at 50:1 gasoline/oil ratio.

 

 

 

 

 

 

 

 

 

 

Consult with an authorized servicing dealer.

 

 

 

 

 

 

Carbon deposits on the piston or in the muffler.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Clogged air filter.

 

Service the air filter.

Engine is rough at all speeds.

 

 

 

 

 

 

 

 

May also have black smoke and/

 

 

 

Loose or damaged spark plug.

 

Tighten or replace.

 

 

 

 

or unburned fuel at the exhaust.

 

 

 

Air leakage or clogged fuel line.

 

Repair or replace fuel filter and/or fuel line.

 

 

 

 

 

 

 

 

 

Water in the fuel.

 

Refill with fresh fuel/oil mixture. See page 8.

 

 

 

 

 

 

 

 

 

Piston seizure.

 

Consult with an authorized servicing dealer.

 

 

 

 

 

 

 

 

 

Faulty carburetor and/or diaphragm.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Overheating condition.

 

See above.

Engine is knocking.

 

 

 

 

 

 

 

Improper fuel.

 

Check fuel octane rating; check for presence of

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

alcohol in the fuel (page 8). Refuel as necessary.

 

 

 

 

 

 

 

 

 

 

Carbon deposits in the combustion chamber.

 

Consult with an authorized servicing dealer.

 

 

 

 

 

15

Image 15
Contents LE261 LE261/EVC Lawn EdgerContents General Safety InstructionsIntroduction General Safety Instructions The Properly Equipped Operator Stay AlertUse Good Judgment Be Aware of the Working Environment Safety LabelsSpecifications Prior to AssemblyProduct Description Refer to Figures 7 and 7a Assembly Driveshaft and PowerheadAssembly Throttle Linkage and Ignition Leads Connect the Outer Tube to the PowerheadAssembly Throttle Cable Free Play Adjustment Assembly HandleConnect the Handle to Outer Tube Assembly Attachment Shield and Edger Blade Mixing FuelFilling the Fuel Tank Starting a Warm Engine When the Engine StartsStarting the Engine Stopping the EngineEdging with an Hand-held Edger Adjusting Engine IdleIdle Speed Adjustment Checking Unit ConditionGeneral Maintenance Adjusting the Blade Cutting DepthDaily Maintenance Hour Maintenance10/15-Hour Maintenance Inspect the Gearcase Protector Lubricate the Flexible ShaftEvery 135 hours of operation Long Term StoragePossible Cause Troubleshooting GuideSymptom Possible Cause Remedy What is Covered by this Warranty Your Warranty Rights and ObligationsOwners Warranty Responsibilities Manufacturer’s Warranty CoveragePage