Shindaiwa 81645 manual Manufacturers Warranty Coverage

Page 17

The following statement only applies to United States and its territories

Shindaiwa Corporation

Federal Emission Design And Defect Limited Warranty

Utility And Lawn And Garden Engines

Shindaiwa Corporation warrants to the initial purchaser and each subsequent owner, that this utility equipment engine (herein engine) is designed, built and equipped to conform at the time of initial sale, to all applicable regulations of the U.S. Environmental Protection Agency (EPA), and that the engine is free of defects in materials and workmanship that would cause this engine to fail to conform with EPA regulations during its warranty period. This emission warranty is applicable in all States, except the State of California.

For parts listed under PARTS COVERED, the dealer authorized by Shindaiwa Corporation will, at no cost to you, make the necessary diagnosis, repair, or replacement of any defective emission-related component to ensure that the engine complies with applicable U.S. EPA regulations.

MANUFACTURERS WARRANTY COVERAGE

When sold within the U.S., this engine’s emission control system is warranted for a period of two (2) years from the date this product is first delivered to the original retail purchaser.

OWNER’S WARRANTY RESPONSIBILITIES

As the engine owner, you are responsible for the performance of the re- quired maintenance listed in your owner’s manual. Shindaiwa Corporation recommends that you retain all receipts covering maintenance on your engine, but Shindaiwa Corporation cannot deny a warranty claim solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance.

As the engine owner, you should however be aware that Shindaiwa Corporation may deny your warranty coverage if your engine or a part has failed due to abuse, neglect, improper maintenance or unapproved modifications.

You are responsible for presenting your engine to the nearest dealer authorized by Shindaiwa Corporation when a problem exists.

If your Shindaiwa Dealer is unable to answer questions regarding your warranty rights and responsibilities, you should then contact your Shindaiwa Distributor.

For the name and telephone number of the Shindaiwa Distributor in your area, please call Shindaiwa Inc. at (503) 692-3070 between the hours of 8:00 AM and 5:00 PM Pacific Standard Time.

LIMITATIONS

The Federal Emission Design and Defect Warranty shall not cover any of the following:

(a)conditions resulting from tampering, misuse, improper adjustment (unless they were made by the dealer or service center authorized by Shindaiwa Corporation during a warranty repair), alteration, accident, failure to use the recommended fuel and oil, or not per- forming required maintenance services,

(b)the replacement parts used for required maintenance services,

(c)consequential parts used for required maintenance services,

(d)diagnosis and inspection fees that do not result in eligible warranty service being performed, and

(e)any non-authorized replacement part, or malfunction of authorized parts due to use of non-authorized parts.

MAINTENANCE AND REPAIR REQUIREMENTS

You are responsible for the proper use and maintenance of the engine. You should keep all receipts and maintenance records covering the perfor- mance of regular maintenance in the event questions arise. These receipts and maintenance records should be transferred to each subsequent owner of the engine. Shindaiwa Corporation reserves the right to deny warranty coverage if the owner has not properly maintained the engine. Shindaiwa Corporation will not deny warranty repairs, however, solely because of the lack of repair, maintenance or failure to keep maintenance records.

MAINTENANCE, REPLACEMENT OR REPAIR OF EMISSION CONTROL DEVICES AND SYSTEMS MAY BE PERFORMED BY ANY REPAIR ESTABLISHMENT OR INDIVIDUAL; HOWEVER, WARRANTY REPAIRS MUST BE PERFORMED BY A DEALER OR SERVICE CENTER AUTHORIZED BY SHINDAIWA CORPORATION THE USE OF PARTS THAT ARE NOT EQUIVALENT IN PERFORMANCE AND DURABILITY TO AUTHORIZED PARTS MAY IMPAIR THE EFFECTIVENESS OF THE EMISSION CONTROL SYSTEM AND MAY HAVE A BEARING ON THE OUTCOME OF A WARRANTY CLAIM.

If other than the parts authorized by Shindaiwa Corporation are used for maintenance replacements or for the repair of components affecting emis- sion control, you should assure yourself that such parts are warranted by their manufacturer to be equivalent to the parts authorized by Shindaiwa Corporation in their performance and durability.

PARTS COVERED

Listed below are the parts covered by the Federal Emission Design and Defect Warranty. Some parts listed below may require scheduled main- tenance and are warranted up to the first scheduled replacement of that part. The warranted parts include:

1.Carburetor Internal Components

Valve Assembly-throttle, Jet, Metering Diaphragm

2.Ignition System Components

Ignition Coil

Flywheel Rotor

The emission control system for your particular Shindaiwa engine may also include certain related hoses and connectors.

OBTAINING WARRANTY SERVICE

All repairs qualifying under this limited warranty must be performed by a dealer authorized by Shindaiwa Corporation

If any emission-related part is found defective during the warranty period, it is your responsibility to present the product to an authorized Shindaiwa dealer. Bring your sales receipts showing the date of purchase for this engine. The dealer authorized by Shindaiwa Corporation will perform the necessary repairs or adjustments within a reasonable amount of time and furnish you with a copy of the repair order. All parts and accessories re- placed under this warranty become the property of Shindaiwa Corporation

To locate an authorized Shindaiwa dealer near you, contact your Shindaiwa Distributor. For the name and telephone number of the Shindaiwa Distributor in your area, please call Shindaiwa Inc. at (503) 692-

3070 between the hours of 8:00 AM and 5:00 PM Pacific Standard Time.

THIS WARRANTY IS ADMINISTERED BY

Shindaiwa Inc.

11975 S.W. Herman Rd. Tualatin OR. 97062 (503) 692-3070

17

Image 17
Contents LE242 Lawn Edger Introduction Safety InstructionsContents Use Good Judgment Safety Instructions Properly Equipped OperatorBe Aware of the Working Environment Safety LabelsProduct Description SpecificationsPrior to Assembly Assembly and Adjustments Assembly and Adjustments Install Gearcase AssemblyAdjust Throttle Lever Free Play Reinstall the air cleaner coverExamples of 501 mixing quantities Mixing FuelFilling the Fuel Tank Starting the Engine Slide the ignition switch to the on position. See FigureWhen the Engine Starts Stopping the Engine Idle Speed AdjustmentChecking Unit Condition Use only authorized Shindaiwa partsAdjusting the Cutting Depth Using a Hand-held EdgerTo adjust blade height Guidelines for Operating the EdgerHour Maintenance General MaintenanceDaily Maintenance Lubricate the Flexible Shaft 10/15-Hour MaintenanceEvery 10 to 15 hours of operation Dealer Inspect the Gearcase ProtectorWith an authorized Shindaiwa servicing Long Term Storage Replacing the Edger BladeEngine does not Start Troubleshooting GuideAdditional Problems Manufacturers Warranty Coverage Page Japan73-167,3 Com.shindaiwa.wwwHiroshima Ku,-Asaminami Nishi-Ozuka-611,2 Oregon TualatinGarantía DE Servicio DE Solicitudes Adicionales Problemas Continuación Diagnostico GuiaPotencia Baja Diagnostico GuiaEstabilizador con Plazo Largo de AlmacenamientoOrilladora la de Cuchilla la Reemplazar Engranajes de Caja la de Protector el Inspeccione Mantenimiento horas 135 CadaContinuación Horas 50 Cada Mantenimiento Precaución Horas 50 Cada MantenimientoHoras 10/15 Cada Mantenimiento General Mantenimiento Diario MantenimientoSujetadores BujíaMano de Orillador el Utilizando Corte del Profundidad la AjustandoShindaiwa marca de lador Oril para cuchillas sólo Utilice Cuchilla de altura la ajustar ParaMotor del Parada Unidad la de Condición la VerifiqueMotor del Mínima Marcha de Ajuste Encendido Motor del Arranque…motor el arranca Cuando De proporción Combustible de Tanque el LlenandoCombustible de Mezcla Engranaje de Caja la de Instalación Acelerador del Holgura la Ajuste Ajustes y EnsamblajeAire de filtro del tapa la Reinstale Seguridad de tuercas las AprieteEnsamblar de Antes EspecificacionesDe normal operación la durante operador Autorizadas no teraciones Al o modificaciones haga NoTrabajo de Area del Alerta Esté Seguridad de EtiquetasDescalzo! máquina la Juicio Buen Use ¡ADVERTENCIAIncendios ContenidoDe Riesgo El Disminuya Cuidado con TrabajeRev 81645 pieza de Número

81645 specifications

The Shindaiwa 81645 is a powerful and versatile tool designed for professional landscapers and gardeners who rely on performance and durability. This product excels in providing efficient power and productivity for a variety of landscaping tasks, making it a favored choice among outdoor maintenance professionals.

One of the key features of the Shindaiwa 81645 is its powerful engine. It is equipped with a high-performance 25.4cc 2-stroke engine that delivers robust power and reliability. This engine not only provides the necessary strength for cutting through dense brush and tough weeds but also operates efficiently to minimize fuel consumption. The combination of power and efficiency is essential for those who spend long hours in the field.

Durability is another hallmark of the Shindaiwa 81645. Built with professional-grade materials, this product can withstand the rigors of daily use in demanding environments. The unit's rugged construction, combined with its advanced vibration dampening technology, ensures that operators experience reduced fatigue, allowing for longer work sessions without discomfort.

The Shindaiwa 81645 also features an ergonomic design, making it comfortable to handle. The adjustable harness allows customization for a secure fit, distributing the weight evenly across the operator's body. This attention to user comfort promotes better handling and control of the tool, leading to improved efficiency and results.

One of the standout technologies integrated into the Shindaiwa 81645 is its Easy Start system, which significantly reduces the effort needed to start the engine. This feature is particularly beneficial in cold weather or when the equipment has not been used for an extended period. Additionally, the tool includes a heavy-duty cutting head that is designed to handle various mowing applications, from trimming grass to tackling thicker underbrush.

Furthermore, the Shindaiwa 81645 boasts a low emissions design, in line with eco-friendly standards. This makes it an environmentally conscious option for professionals who are mindful of their carbon footprint while still demanding high performance from their equipment.

In summary, the Shindaiwa 81645 is a robust tool that merges power, durability, and user-friendly features. With its powerful engine, ergonomic design, and advanced technologies, it stands as a premier choice for landscaping professionals seeking efficiency and reliability in their day-to-day operations. Whether trimming grass or clearing brush, the Shindaiwa 81645 delivers the performance needed to tackle any outdoor challenge.