Shindaiwa 81645 manual Stopping the Engine, Checking Unit Condition, Idle Speed Adjustment

Page 9

Stopping the Engine

OFF

251029

Figure 14

Idle the engine briefly before stopping (about 2 minutes), then slide the ignition switch to the “O” (Engine OFF) position.

Adjusting Engine Idle

 

Idle Adjusting

Figure 15

Screw

 

The engine must return to idle speed whenever the throttle lever is released. Idle speed is adjustable, and must be set low enough to permit the engine clutch to disengage the cutting attachment.

Idle Speed Adjustment

WARNING!

The cutting attachment must NEVER rotate at engine idle! If

the idle speed cannot be adjusted by the procedure described here, return the trimmer to your Shindaiwa dealer for inspection.

1.Place the trimmer on the ground, then start the engine, and then allow it to idle 2-3 minutes until warm.

2.If the attachment rotates when the engine is at idle, reduce the idle speed by turning the idle adjustment screw counter-clockwise. See Figure 15.

3.If a tachometer is available, the engine idle speed should be final adjusted to 3,000 (±250) rpm (min-1).

4.Carburetor fuel mixture adjustments are preset at factory and cannot be serviced in the field.

Checking Unit Condition

NEVER operate the unit with the cut- ting attachment shield or other protective devices removed!

WARNING!

A cutting attachment shield or other protective device is no guaran- tee of protection against ricochet. YOU MUST ALWAYS GUARD AGAINST FLY- ING DEBRIS!

Use only authorized Shindaiwa parts

and accessories with your Shindaiwa trim- mer. Do not make modifications to this unit without written approval from Shindaiwa, Inc.

ALWAYS make sure the cutting attach- ment is properly installed and firmly tight- ened before operation.

NEVER use a cracked or warped cutting at- tachment: replace it with a serviceable one.

ALWAYS make sure the cutting attach- ment fits properly into the appropriate attachment holder. If a properly installed at- tachment vibrates, replace the attachment with new one and re-check.

ALWAYS stop the engine immediately and

check for damage if you strike a foreign object or if the unit becomes tangled. Do not operate with broken or damaged equip- ment.

NEVER allow the engine to run at high RPM without a load. Doing so could dam- age the engine.

NEVER operate a unit with worn or dam- aged fasteners or attachment holders.

Image 9
Contents LE242 Lawn Edger Safety Instructions ContentsIntroduction Use Good Judgment Safety Instructions Properly Equipped OperatorBe Aware of the Working Environment Safety LabelsSpecifications Prior to AssemblyProduct Description Assembly and Adjustments Assembly and Adjustments Install Gearcase AssemblyAdjust Throttle Lever Free Play Reinstall the air cleaner coverMixing Fuel Filling the Fuel TankExamples of 501 mixing quantities Slide the ignition switch to the on position. See Figure When the Engine StartsStarting the Engine Stopping the Engine Idle Speed AdjustmentChecking Unit Condition Use only authorized Shindaiwa partsAdjusting the Cutting Depth Using a Hand-held EdgerTo adjust blade height Guidelines for Operating the EdgerGeneral Maintenance Daily MaintenanceHour Maintenance 10/15-Hour Maintenance Every 10 to 15 hours of operationLubricate the Flexible Shaft Inspect the Gearcase Protector With an authorized Shindaiwa servicingDealer Long Term Storage Replacing the Edger BladeEngine does not Start Troubleshooting GuideAdditional Problems Manufacturers Warranty Coverage Page Japan73-167,3 Com.shindaiwa.wwwHiroshima Ku,-Asaminami Nishi-Ozuka-611,2 Oregon TualatinGarantía DE Servicio DE Solicitudes Adicionales Problemas Continuación Diagnostico GuiaPotencia Baja Diagnostico GuiaPlazo Largo de Almacenamiento Orilladora la de Cuchilla la ReemplazarEstabilizador con Mantenimiento horas 135 Cada Continuación Horas 50 Cada MantenimientoEngranajes de Caja la de Protector el Inspeccione Horas 50 Cada Mantenimiento Horas 10/15 Cada MantenimientoPrecaución General Mantenimiento Diario MantenimientoSujetadores BujíaMano de Orillador el Utilizando Corte del Profundidad la AjustandoShindaiwa marca de lador Oril para cuchillas sólo Utilice Cuchilla de altura la ajustar ParaUnidad la de Condición la Verifique Motor del Mínima Marcha de AjusteMotor del Parada Motor del Arranque …motor el arranca CuandoEncendido Combustible de Tanque el Llenando Combustible de MezclaDe proporción Engranaje de Caja la de Instalación Acelerador del Holgura la Ajuste Ajustes y EnsamblajeAire de filtro del tapa la Reinstale Seguridad de tuercas las AprieteEnsamblar de Antes EspecificacionesDe normal operación la durante operador Autorizadas no teraciones Al o modificaciones haga NoTrabajo de Area del Alerta Esté Seguridad de EtiquetasDescalzo! máquina la Juicio Buen Use ¡ADVERTENCIAIncendios ContenidoDe Riesgo El Disminuya Cuidado con TrabajeRev 81645 pieza de Número

81645 specifications

The Shindaiwa 81645 is a powerful and versatile tool designed for professional landscapers and gardeners who rely on performance and durability. This product excels in providing efficient power and productivity for a variety of landscaping tasks, making it a favored choice among outdoor maintenance professionals.

One of the key features of the Shindaiwa 81645 is its powerful engine. It is equipped with a high-performance 25.4cc 2-stroke engine that delivers robust power and reliability. This engine not only provides the necessary strength for cutting through dense brush and tough weeds but also operates efficiently to minimize fuel consumption. The combination of power and efficiency is essential for those who spend long hours in the field.

Durability is another hallmark of the Shindaiwa 81645. Built with professional-grade materials, this product can withstand the rigors of daily use in demanding environments. The unit's rugged construction, combined with its advanced vibration dampening technology, ensures that operators experience reduced fatigue, allowing for longer work sessions without discomfort.

The Shindaiwa 81645 also features an ergonomic design, making it comfortable to handle. The adjustable harness allows customization for a secure fit, distributing the weight evenly across the operator's body. This attention to user comfort promotes better handling and control of the tool, leading to improved efficiency and results.

One of the standout technologies integrated into the Shindaiwa 81645 is its Easy Start system, which significantly reduces the effort needed to start the engine. This feature is particularly beneficial in cold weather or when the equipment has not been used for an extended period. Additionally, the tool includes a heavy-duty cutting head that is designed to handle various mowing applications, from trimming grass to tackling thicker underbrush.

Furthermore, the Shindaiwa 81645 boasts a low emissions design, in line with eco-friendly standards. This makes it an environmentally conscious option for professionals who are mindful of their carbon footprint while still demanding high performance from their equipment.

In summary, the Shindaiwa 81645 is a robust tool that merges power, durability, and user-friendly features. With its powerful engine, ergonomic design, and advanced technologies, it stands as a premier choice for landscaping professionals seeking efficiency and reliability in their day-to-day operations. Whether trimming grass or clearing brush, the Shindaiwa 81645 delivers the performance needed to tackle any outdoor challenge.