Shindaiwa 81645 Starting the Engine, Slide the ignition switch to the on position. See Figure

Page 8

Starting the Engine

IMPORTANT!!

Engine ignition is controlled by a two position switch mounted on the throttle housing labeled, “I” for ON or START and “O” for OFF or STOP.

ON

Figure 9

1.Slide the ignition switch to the “ON” position. See Figure 9.

Return Tube

Primer Bulb

Figure 10

2.Press the primer bulb until fuel can be seen flowing in the transparent return tube.

IMPORTANT!

The primer system only pushes fuel through the carburetor. Repeatedly pressing the primer bulb will not flood the engine with fuel.

3.Set the choke lever to the CLOSED position if engine is cold.

Closed

Figure 11

Make sure the cutting attach- ment

is clear of ob-

structions!

Figure 12

4.While holding the outer tube firmly with left hand. Use your other hand to slowly pull the recoil starter handle until resis- tance is felt, then pull quickly to start the engine.

CAUTION!

Do not pull the recoil starter to the end of the rope travel. Pulling the recoil starter to the end of the rope travel can damage the starter.

WARNING!

The cutting attachment may rotate when the engine is started!

5.When the engine starts, slowly move the choke lever to the “OPEN” position. See Figure 13. (If the engine stops after the initial start, close the choke and restart.)

Open

Figure 13

WARNING!

Never start the engine from the operating position.

IMPORTANT!

If the engine fails to start after several at- tempts with the choke in the closed posi- tion, the engine may be flooded with fuel. If flooding is suspected, move the choke lever to the open position and repeatedly pull the recoil starter to remove excess fuel and start the engine. If the engine still fails to start, refer to the troubleshooting section of this manual.

When the Engine Starts...

nAfter the engine starts, allow the engine to warm up at idle 2 or 3 minutes before operating the unit.

nAdvancing the throttle makes the cut- ting attachment turn faster; releasing the throttle permits the attachment to stop turning. If the cutting attachment continues to rotate when the engine returns to idle, carburetor idle speed should be adjusted (see “Adjusting Engine Idle” on next page).

Page 7 Page 9
Image 8
Page 7 Page 9
Contents LE242 Lawn Edger Introduction Safety InstructionsContents Safety Instructions Properly Equipped Operator Use Good JudgmentSafety Labels Be Aware of the Working EnvironmentProduct Description SpecificationsPrior to Assembly Assembly and Adjustments Install Gearcase Assembly Assembly and AdjustmentsAdjust Throttle Lever Free Play Reinstall the air cleaner coverExamples of 501 mixing quantities Mixing FuelFilling the Fuel Tank Starting the Engine Slide the ignition switch to the on position. See FigureWhen the Engine Starts Idle Speed Adjustment Stopping the EngineChecking Unit Condition Use only authorized Shindaiwa partsUsing a Hand-held Edger Adjusting the Cutting DepthTo adjust blade height Guidelines for Operating the EdgerHour Maintenance General MaintenanceDaily Maintenance Lubricate the Flexible Shaft 10/15-Hour MaintenanceEvery 10 to 15 hours of operation Dealer Inspect the Gearcase ProtectorWith an authorized Shindaiwa servicing Replacing the Edger Blade Long Term StorageTroubleshooting Guide Engine does not StartAdditional Problems Manufacturers Warranty Coverage Page Com.shindaiwa.www Japan73-167,3Hiroshima Ku,-Asaminami Nishi-Ozuka-611,2 Oregon TualatinGarantía DE Servicio DE Solicitudes Continuación Diagnostico Guia Adicionales ProblemasDiagnostico Guia Potencia BajaEstabilizador con Plazo Largo de AlmacenamientoOrilladora la de Cuchilla la Reemplazar Engranajes de Caja la de Protector el Inspeccione Mantenimiento horas 135 CadaContinuación Horas 50 Cada Mantenimiento Precaución Horas 50 Cada MantenimientoHoras 10/15 Cada Mantenimiento Diario Mantenimiento General MantenimientoSujetadores BujíaCorte del Profundidad la Ajustando Mano de Orillador el UtilizandoShindaiwa marca de lador Oril para cuchillas sólo Utilice Cuchilla de altura la ajustar ParaMotor del Parada Unidad la de Condición la VerifiqueMotor del Mínima Marcha de Ajuste Encendido Motor del Arranque…motor el arranca Cuando De proporción Combustible de Tanque el LlenandoCombustible de Mezcla Acelerador del Holgura la Ajuste Ajustes y Ensamblaje Engranaje de Caja la de InstalaciónAire de filtro del tapa la Reinstale Seguridad de tuercas las AprieteEspecificaciones Ensamblar de AntesDe normal operación la durante operador Autorizadas no teraciones Al o modificaciones haga NoSeguridad de Etiquetas Trabajo de Area del Alerta EstéJuicio Buen Use ¡ADVERTENCIA Descalzo! máquina laContenido IncendiosDe Riesgo El Disminuya Cuidado con TrabajeRev 81645 pieza de Número

81645 specifications

The Shindaiwa 81645 is a powerful and versatile tool designed for professional landscapers and gardeners who rely on performance and durability. This product excels in providing efficient power and productivity for a variety of landscaping tasks, making it a favored choice among outdoor maintenance professionals.

One of the key features of the Shindaiwa 81645 is its powerful engine. It is equipped with a high-performance 25.4cc 2-stroke engine that delivers robust power and reliability. This engine not only provides the necessary strength for cutting through dense brush and tough weeds but also operates efficiently to minimize fuel consumption. The combination of power and efficiency is essential for those who spend long hours in the field.

Durability is another hallmark of the Shindaiwa 81645. Built with professional-grade materials, this product can withstand the rigors of daily use in demanding environments. The unit's rugged construction, combined with its advanced vibration dampening technology, ensures that operators experience reduced fatigue, allowing for longer work sessions without discomfort.

The Shindaiwa 81645 also features an ergonomic design, making it comfortable to handle. The adjustable harness allows customization for a secure fit, distributing the weight evenly across the operator's body. This attention to user comfort promotes better handling and control of the tool, leading to improved efficiency and results.

One of the standout technologies integrated into the Shindaiwa 81645 is its Easy Start system, which significantly reduces the effort needed to start the engine. This feature is particularly beneficial in cold weather or when the equipment has not been used for an extended period. Additionally, the tool includes a heavy-duty cutting head that is designed to handle various mowing applications, from trimming grass to tackling thicker underbrush.

Furthermore, the Shindaiwa 81645 boasts a low emissions design, in line with eco-friendly standards. This makes it an environmentally conscious option for professionals who are mindful of their carbon footprint while still demanding high performance from their equipment.

In summary, the Shindaiwa 81645 is a robust tool that merges power, durability, and user-friendly features. With its powerful engine, ergonomic design, and advanced technologies, it stands as a premier choice for landscaping professionals seeking efficiency and reliability in their day-to-day operations. Whether trimming grass or clearing brush, the Shindaiwa 81645 delivers the performance needed to tackle any outdoor challenge.
Top Page Image Contents