Shindaiwa 81704 manual Stopping the Engine, Adjusting Engine Idle, When the Engine Starts

Page 11

Starting the Engine (continued)

WARNING!

The cutting attachment may rotate when the engine is started!

6.When the engine starts, slowly move the choke lever to the "OPEN" position. See Figure 20. (If the engine stops after the initial start, close the choke and restart.)

Open

Figure 20

WARNING!

Never start the engine from the oper- ating position.

7.Operating the throttle will automatically disengage the fast idle setting.

IMPORTANT!

If the engine fails to start after several at- tempts with the choke in the closed posi- tion, the engine may be flooded with fuel. If flooding is suspected, move the choke lever to the open position and repeatedly pull the recoil starter to remove excess fuel and start the engine. If the engine still fails to start, refer to the troubleshooting section of this manual.

When the Engine Starts...

nAfter the engine starts, allow the en- gine to warm up at idle 2 or 3 minutes before operating the unit.

nAfter the engine is warm, pick up the unit and clip on the shoulder strap. See page 12.

nAdvancing the throttle makes the cut- ting attachment turn faster; releasing the throttle permits the attachment to stop turning. If the cutting attachment continues to rotate when the engine returns to idle, carburetor idle speed should be adjusted (see "Adjusting Engine Idle" below).

Stopping the Engine

OFF

Idle the engine briefly before stopping (about 2 minutes), then slide the ignition switch to the “O” (Engine OFF) position.

C2510

Figure 21

Adjusting Engine Idle

 

Idle Adjusting

Figure 22

Screw

 

 

The engine must return to idle speed whenever the throttle lever is released. Idle speed is adjustable, and must be set low enough to permit the engine clutch to disengage the cutting attachment.

Idle Speed Adjustment

WARNING!

The cutting attachment must NEVER rotate at engine idle! If the idle speed cannot be adjusted by the procedure described here, return the trimmer to your Shindaiwa dealer for inspection.

1.Place the trimmer on the ground, then start the engine, and then allow it to idle 2-3 minutes until warm.

2.If the attachment rotates when the engine is at idle, reduce the idle speed by turning the idle adjustment screw counter-clockwise. See Figure 22.

3.If a tachometer is available, the engine idle speed should be final adjusted to 3,000 (±300) RPM (min-1).

4.Carburetor fuel mixture adjustments are preset at factory and cannot be serviced in the field.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents C2510 C2510 BrushcutterIntroduction ContentsSafety Instructions Always use the proper cutting tool for the job Properly Equipped OperatorBe Aware of the Working Environment Safety LabelsProduct Description Specifications C2510Prior to Assembly Sub-Shield C2510 AssemblyInstall the Cutting Attachment Shield C2510 Cutting Attachment ShieldReinstall the air cleaner cover AdjustmentsHandle Bar C2510 Install the handlebar Adjust Throttle Lever Free PlayGear Case Shaft Installing a Trimmer HeadRemove the hex wrench Installing a BladeExamples of 501 mixing quantities Mixing FuelFilling the Fuel Tank Starting the EngineStopping the Engine Adjusting Engine IdleWhen the Engine Starts Idle Speed AdjustmentCutting Grass-Units equipped with a trimmer head Checking Unit ConditionShoulder Strap C2510 Operating Units with a Blade Using a Blade C2510Hour Maintenance General MaintenanceDaily Maintenance Every 10 to 15 hours of operation 10/15-Hour MaintenanceSpark Arrester Screen Maintenance 139/150-Hour MaintenanceMultiple-tooth Circular Blade Long Term StorageBlade Sharpening Shindaiwa Tornado BladeEngine does not Start Troubleshooting GuideAdditional Problems Manufacturers Warranty Coverage Garantía DE Servicio DE Solicitudes Adicionales Problemas Continuación Diagnostico Guia18SP Diagnostico GuiaTornado Shindaiwa Disco Discos de AfiladoPlazo Largo de Almacenamiento Múltiples Dientes de DiscosTorsión de correctas Guardachispas Maya la de MantenimientoMantenimiento o horas 139/150 Cada Shindaiwa autorizadoHoras 10/15 Cada Mantenimiento Horas 50 Cada MantenimientoGeneral Mantenimiento Horas 10 Cada MantenimientoDiario Mantenimiento C2510 Disco un Usando Cuchilla una con Unidades OperandoUnidad la de Condición la Verifique Corte de Cabezal con Equipadas Máquinas Césped de CorteMínima Marcha de Ajuste Motor del Mínima Marcha de AjusteMotor del Parada Continuación Motor del ArranqueDe proporción a mezcla Motor del ArranqueCombustible de Tanque el Llenando Combustible de MezclaCuchilla la Instalando Nylon de Cabezal del Instalación C2510 Mango Continuación EnsamblajeSeguridad de tuercas las Apriete Acelerador del holgura la Ajuste AjustesEnsamblaje Ensamblar de Antes C2510 EspecificacionesProducto del Descripción Trabajo de Area del Alerta Esté Seguridad de EtiquetasLimpios mangos los mantenga Siempre Equipado Debidamente Operario El Seguridad de InstruccionesCuidado con Trabaje ContenidoHumana reproducción la Nocivos efectos otros u congénitos Alerta MantengaseOrador
Top Page Image Contents