Shindaiwa 81704 manual Installing a Blade, Remove the hex wrench

Page 9

Installing a Blade

Turn the C2510 upside down so the gear case output shaft is facing UP and remove the shaft bolt, bolt guard and holder B from the gear case shaft.

1.Align the hole in blade holder A with the matching hole in the gear case flange and then temporarily lock the output shaft by inserting a hex wrench through both holes. See Figure 12.

2.Slide the safety clip off-center. See Figure 13.

3.Fit the blade over the safety clip and then center it over the flange on holder A. See Figure 14.

CAUTION!

Install the blade so its printed surface is visible to the operator when the brushcutter is in the normal operating position.

WARNING!

Shaft Bolt

Bolt Guard

Holder B

Output Shaft

Safety Clip

Holder A

Hex

Wrench

Figure 12

Slide the safety clip off-center

Output

Shaft

Safety

Clip

Figure 13

Slip the Saw Blade	Slide the Safety Clip
In Place	Back

Figure 14

The blade must fit flat against the holder flange. The blade mounting hole must be centered over the raised boss on blade holder A.

NOTE:

When installing certain blades, it may be necessary to temporarily remove the safety clip.

4.Lock the blade in place by centering the safety clip on the output shaft. See Figure 14.

WARNING!

Never operate the C2510 without the safety clip in place!

IMPORTANT!

The machined recess in holder B must

Output

BladeShaft

Blade Holder B	Hex Wrench

Tighten the assembly (blade not

shown for clarity)

Figure 15

completely surround the safety clip, and both holders must be flat against the sur- face of the blade.

5.Install blade holder B on the output shaft. See Figure 15. The recess in the holder must completely cover the safety clip, and must fit tightly against the blade.

6.Install the bolt guard and then the blade retaining bolt. Using the combination spark plug wrench/screwdriver, tighten the bolt firmly in a counter-clockwise direction.

7.Remove the hex wrench.

The C2510 should now be com- pletely assembled and

ready for use with a blade.

Image 9

Contents C2510 C2510 BrushcutterContents Safety InstructionsIntroduction Always use the proper cutting tool for the job Properly Equipped OperatorBe Aware of the Working Environment Safety LabelsSpecifications C2510 Prior to AssemblyProduct Description Install the Cutting Attachment Shield C2510 AssemblyCutting Attachment Shield Sub-Shield C2510Handle Bar C2510 Install the handlebar AdjustmentsAdjust Throttle Lever Free Play Reinstall the air cleaner coverGear Case Shaft Installing a Trimmer HeadRemove the hex wrench Installing a BladeFilling the Fuel Tank Mixing FuelStarting the Engine Examples of 501 mixing quantitiesWhen the Engine Starts Adjusting Engine IdleIdle Speed Adjustment Stopping the EngineChecking Unit Condition Shoulder Strap C2510Cutting Grass-Units equipped with a trimmer head Operating Units with a Blade Using a Blade C2510General Maintenance Daily MaintenanceHour Maintenance Every 10 to 15 hours of operation 10/15-Hour MaintenanceSpark Arrester Screen Maintenance 139/150-Hour MaintenanceBlade Sharpening Long Term StorageShindaiwa Tornado Blade Multiple-tooth Circular BladeEngine does not Start Troubleshooting GuideAdditional Problems Manufacturers Warranty Coverage Garantía DE Servicio DE Solicitudes Adicionales Problemas Continuación Diagnostico Guia18SP Diagnostico GuiaPlazo Largo de Almacenamiento Discos de AfiladoMúltiples Dientes de Discos Tornado Shindaiwa DiscoMantenimiento o horas 139/150 Cada Guardachispas Maya la de MantenimientoShindaiwa autorizado Torsión de correctasHoras 10/15 Cada Mantenimiento Horas 50 Cada MantenimientoHoras 10 Cada Mantenimiento Diario MantenimientoGeneral Mantenimiento C2510 Disco un Usando Cuchilla una con Unidades OperandoUnidad la de Condición la Verifique Corte de Cabezal con Equipadas Máquinas Césped de CorteMotor del Parada Motor del Mínima Marcha de AjusteContinuación Motor del Arranque Mínima Marcha de AjusteCombustible de Tanque el Llenando Motor del ArranqueCombustible de Mezcla De proporción a mezclaCuchilla la Instalando Nylon de Cabezal del Instalación Seguridad de tuercas las Apriete Continuación EnsamblajeAcelerador del holgura la Ajuste Ajustes C2510 MangoEnsamblaje C2510 Especificaciones Producto del DescripciónEnsamblar de Antes Trabajo de Area del Alerta Esté Seguridad de EtiquetasLimpios mangos los mantenga Siempre Equipado Debidamente Operario El Seguridad de InstruccionesHumana reproducción la Nocivos efectos otros u congénitos ContenidoAlerta Mantengase Cuidado con TrabajeOrador