Shindaiwa 81704 manual Assembly, Install the Cutting Attachment Shield C2510, Sub-Shield C2510

Page 6

Assembly

Cutting Attachment Shield

	Socket-	Bracket
	Socket-
	Head Cap	Outer
	Screw	Outer
	Screw	Tube
		Tube

Shim

Clamp Screw

		Shim
Retaining Nut	Cutting	Cutting Attach-
	Attachment Mounting	Cutting Attach-
	Attachment Mounting	ment Shield
	Plate	ment Shield
	Plate

Figure 9

Cutting Attachment Shield

Line Cutter
	Sub-shield with
Figure 9A	Line Cutter
Figure 9A

Install the Cutting Attachment Shield C2510.

1.Insert the cutting attachment shield between the outer tube and the cutting attachment mounting plate. See Figure 9.

NOTE:

It may be necessary to loosen the retaining nut and clamp screw to adjust cutting attach- ment shield mounting plate.

2.Fit the two shims and the bracket over the outer tube and loosely install the four socket-head screws. See Figure 9.

3.Tighten the four socket-head cap screws to secure the cutting attachment shield.

CAUTION!

Make sure the clamp screw and retaining nut are securely tightened before tightening the four socket-head cap screws.

WARNING!

NEVER operate the unit without the cutting attachment shield installed and tightly secured!

Sub-Shield C2510.

(when trimmer head is in use)

1.Attach the shield extension to the cut- ting attachment shield. See figure 9B.

WARNING!

NEVER use this machine without sub-shield when using a trimmer head.

Cutting Attachment Shield

Hook

Receiver

Hook Sub-shield

Figure 9B

CAUTION!

Make sure the sub-guard is com- pletely hooked at the hook receiver.

Image 6

Contents C2510 Brushcutter C2510Contents Safety InstructionsIntroduction Properly Equipped Operator Always use the proper cutting tool for the jobSafety Labels Be Aware of the Working EnvironmentSpecifications C2510 Prior to AssemblyProduct Description Cutting Attachment Shield AssemblyInstall the Cutting Attachment Shield C2510 Sub-Shield C2510Adjust Throttle Lever Free Play AdjustmentsHandle Bar C2510 Install the handlebar Reinstall the air cleaner coverInstalling a Trimmer Head Gear Case ShaftInstalling a Blade Remove the hex wrenchStarting the Engine Mixing FuelFilling the Fuel Tank Examples of 501 mixing quantitiesIdle Speed Adjustment Adjusting Engine IdleWhen the Engine Starts Stopping the EngineChecking Unit Condition Shoulder Strap C2510Cutting Grass-Units equipped with a trimmer head Using a Blade C2510 Operating Units with a BladeGeneral Maintenance Daily MaintenanceHour Maintenance 10/15-Hour Maintenance Every 10 to 15 hours of operation139/150-Hour Maintenance Spark Arrester Screen MaintenanceShindaiwa Tornado Blade Long Term StorageBlade Sharpening Multiple-tooth Circular BladeTroubleshooting Guide Engine does not StartAdditional Problems Manufacturers Warranty Coverage Garantía DE Servicio DE Solicitudes Continuación Diagnostico Guia Adicionales ProblemasDiagnostico Guia 18SPMúltiples Dientes de Discos Discos de AfiladoPlazo Largo de Almacenamiento Tornado Shindaiwa DiscoShindaiwa autorizado Guardachispas Maya la de MantenimientoMantenimiento o horas 139/150 Cada Torsión de correctasHoras 50 Cada Mantenimiento Horas 10/15 Cada MantenimientoHoras 10 Cada Mantenimiento Diario MantenimientoGeneral Mantenimiento Cuchilla una con Unidades Operando C2510 Disco un UsandoCorte de Cabezal con Equipadas Máquinas Césped de Corte Unidad la de Condición la VerifiqueContinuación Motor del Arranque Motor del Mínima Marcha de AjusteMotor del Parada Mínima Marcha de AjusteCombustible de Mezcla Motor del ArranqueCombustible de Tanque el Llenando De proporción a mezclaCuchilla la Instalando Nylon de Cabezal del Instalación Acelerador del holgura la Ajuste Ajustes Continuación EnsamblajeSeguridad de tuercas las Apriete C2510 MangoEnsamblaje C2510 Especificaciones Producto del DescripciónEnsamblar de Antes Seguridad de Etiquetas Trabajo de Area del Alerta EstéEquipado Debidamente Operario El Seguridad de Instrucciones Limpios mangos los mantenga SiempreAlerta Mantengase ContenidoHumana reproducción la Nocivos efectos otros u congénitos Cuidado con TrabajeOrador