DSCover Satellite Products SCW904x manual Installation & Wiring, Technical Summary

Section 1: Installation & Wiring

Section 1: Installation & Wiring

This Installation Guide provides the basic installation, wiring and programming information for the PowerSeries Self Contained Wireless (SCW) Security System.

This publication covers the following versions of the SCW Security System:

SCW9045-433 v1.0	SCW9045-868 v1.0
SCW9047-433 v1.0	SCW9047-868 v1.0
	These models are not UL/ULC Listed (intended for European market only)

TECHNICAL SUMMARY
Specifications
Temp Range	0°C-49°C (32°F-120°F)
Humidity (Max)	93%RH Non Condensing.
Power Supply	16.5VAC/20VA @50/60Hz.
Current Draw from Transformer	400mA AC (Max.)
Aux+ Output	12.0-12.5VDC/100mA
Features
Wireless Zones	32
*On-board I/O	2
Partitions	1
Wireless Keys	16
User Codes	16 + 1 Master Code
Event Buffer	128 Events
LCD Display	2 Rows x 16 Char
Plug-in Transformer	Secondary 16.5 VAC/20-40VA
Battery Backup	7.2VDC@1500 mAH
(24Hr Backup)

*I/O Terminals can be configured as Zone Inputs or PGM Outputs When configured as PGMs, outputs are 50mA

Compatible Wireless Devices

SCW9045-433 v1.0	all DSC 433 or 433EU Devices
SCW9047-433 v1.0	all DSC 433 or 433EU Devices
SCW9045-868 v1.0	all DSC 868 Devices
SCW9047-868 v1.0	all DSC 868 Devices

UL Listed Wireless Devices

WS4904(P)	PIR Motion Detector
WS4916	Smoke Detector
WS4945	Door Contact
WS4965	Door Contact
WLS912L-433	Glass Break Detector
WLS914-433	PIR Motion Detector
WS4938	Panic Pendant
WS4939	Wireless Key

Classified in Accordance with ANSI/SIA CP-01-2000 (SIA-FAR)

IMPORTANT NOTE!

This equipment, SCW Alarm System shall be installed and used within an environment that provides the pollution degree max 2 and over-voltages category II NON-HAZARDOUS LOCATIONS, indoor only. The equipment is DIRECT PLUG-IN connected and is designed to be installed, serviced and/or repaired by service persons only; [service person is defined as a person having the appropriate technical training and experience necessary to be aware of hazards to which that person may be exposed in performing a task and of measures to minimize the risks to that person or other persons]. There are no parts replaceable by the end-user within this equipment.

The power supply must be direct plug-in,fail safe, with dou- ble or reinforced insulation between primary and secondary circuits. In EU countries it must meet the applicable require- ments of the Low Voltage Directive and protected as per the EN60950-1:2001 Standard Requirements. In all other countries, it must be of an approved type acceptable to the local authori- ties; it is the installer’s responsibility to ensure that the socket- outlet that the transformer is plugged-in, is near the equipment and is easily accessible.

The wiring (cables) used for installation of the SCW Alarm Sys- tem and accessories, shall be insulated with PVC, TFE, PTFE, FEP, Neoprene or Polyamide.

(a)The equipment enclosure must be secured to the building structure before operation.

(b)Internal wiring must be routed in a manner that prevents:

-Excessive strain on wire and on terminal connections;

-Loosening of terminal; connections;

-Damage of conductor insulation

(c)Disposal of the used battery packs shall be made according to the waste recovery and recycling regulations applicable to the intended market.

(d)Before servicing, DISCONNECT the power and telephone connection.

(e)Do NOT route any wiring over circuit boards.

WWW.DIYALARMFORUM.COM1