Servis-Rhino 1485, 1480, 1495 manual Storage and Parking Safety Instructions and Practices

Page 19
(SG-18)
(SL-27)
(SL-26)
(SG-38)
(SG-37)

SAFETY

Use caution and wear protective gloves when handling sharp objects such as blades, knives, and other cutting edges. Be alert to worn component surfaces which have sharp edges. Sharp surfaces can inflict severe laceration injuries if proper hand protection is not worn.

Avoid contact with hot surfaces of the engine or muffler. Use gloves and eye protection when servicing hot components. Contact with a hot surface or fluid can cause serious injury from burns or scalding.

Never allow anyone to get under the loader or attachment or to reach through the loader lift arms when raised. Serious injury could result from crushing or pinching by the loader or attachment. (SL-06)

PARTS INFORMATION

Rhino products are designed utilizing specifically matched system components to ensure optimum equipment performance. These parts are made and tested to Rhino specifications. Non-genuine "will fit" parts do not consistently meet these specifications. The use of “will fit” parts may reduce equipment performance, void warranties, and present a safety hazard. Use genuine Rhino parts for economy and safety. (SPRM-2)

SEE YOUR RHINO DEALER

SAFETY

Storage and Parking Safety Instructions and Practices

Never crawl under or allow children to play around or on a loader that is disconnected from the tractor. The loader could fall crushing a person resulting in serious injury or death. (SL-13)

Do not remove the attachment from the loader when the loader is disconnected from the tractor. The attachment stabilizes the loader. If the attachment is removed, the loader will fall and could result in serious injury.

Only disconnect and store the loader on firm flat ground. Make sure the loader stands are properly installed and rest on firm ground or support blocks. If the stands sink or fail, the loader could fall causing serious injury.

Concluding Safety Instructions and Practices

In addition to the design and configuration of this Implement, including Safety Signs and Safety Equipment, hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper training of personnel involved in the operation, transport, maintenance, and storage of the machine. Refer also to Safety Messages and operation instruction in each of the appropriate sections of the Tractor and Equipment Manuals. Pay close attention to the Safety Signs affixed to the Tractor and Equipment.

1480/1485/1495 01/11

Safety Section 1-15

© 2011 Alamo Group Inc.

Image 19 Contents
1480/1485 1495 To the Owner/Operator/Dealer Table of Contents Maintenance Section Safety Section General Safety Instructions and Practices Safety1480/1485/1495 01/11 Safety Section Operator Safety Instructions and Practices Safety Equipment Operation Safety Instructions and Practices Safety Safety 1480/1485/1495 01/11 Safety Section SL-33 Safety Transporting Safety Instructions and Practices Maintenance and Service Safety Instructions and Practices Safety Concluding Safety Instructions and Practices Storage and Parking Safety Instructions and PracticesDecal Location QTY Level Description Decal Description Safety Safety Safety Safety Federal Laws and Regulations Page Introduction Section Introduction Introductio Introduction Before Operating this Machine Page Assembly and Connecting the Loader Section Assembly Instructions Assembly1480/1485/1495 01/11 Assembly Section Proper Ballasting and Wheel Spacing Dismounting Loader Dismounting and Mounting LoaderMounting Loader Attaching Pin on BucketAssembling Quick-Attach Device Installing Quick-Attach DeviceWhen Connecting an Attachment to the Loader Quick Hitch Plumbing Hydraulic Valve Attaching Tractor Hydraulic Block Attaching Valve Mounting & ValvePlumbing Loader to Control Valve Hose PlumbingPage Operation Section Rhino 1400 Series Loader Operation1480 1485 1495 Standard Equipment and SpecificationsOperator Requirements Operation Personal Protective Equipment PPE Tractor RequirementsTractor Lighting and SMV Emblem Rops and Seat BeltTractor Ballast Boarding the Tractor Getting On and Off the TractorDismounting the Tractor Starting the Tractor Tractor Pre-Operation Inspection/Service Pre-Operation Inspection and ServiceLoader Pre-Operation Inspection and Service Mount Assembly OPS-L-0007B Do not Operate an Unsafe Tractor or Front END Loader Front END Loader PRE-OPERATION Inspection Driving the Tractor and Loader Driving the Tractor and Loader Operating the Tractor and LoaderSG-36 Operation Operation SL-33 Operation Filling the Bucket Operating the LoaderOperation Lifting the Load Dumping the Bucket Operating with Float Control Operation Peeling and Scraping Loading LOW Trucks or Spreaders from a Pile Backfilling Operation Handling Large Heavy Objects Operating Bale Spear Transporting the Tractor and Implement Loader StorageShutting Down the Implement Operation Transporting on Public Roadways Operation Hauling the Tractor and Implement Trouble Possible Cause Possible Remedy Troubleshooting GuideOperation Maintenance Section Maintenance 1480/1485/1495 01/11 Maintenance Section Lubrication Schedule Hydraulic Pressure Check Daily ChecksHydraulic Cylinder Lift and Bucket Cylinder DisassemblyLift and Bucket Cylinder Reassembly Storage Maintenance Proper Torque for Fasteners Maintenance Maintenance Page Rhino To the OWNER/OPERATOR/DEALER 1480/1485/1495