Servis-Rhino 1480, 1485, 1495 manual Safety

Page 18
(SG-34)
(SG-21)
(SG-20)
(SG-15)
(SL-36)
(SG-8)

SAFETY

SAFETY

Do not modify or alter this Implement. Do not permit anyone to modify or alter this Implement, any of its components or any Implement function.

Never work under the Implement, the framework, or any lifted component unless the Implement is securely supported or blocked up to prevent sudden or inadvertent falling which could cause serious injury or even death.

Do not operate this Equipment with hydraulic oil or fuel leaking. Oil and fuel are explosive and their presence could present a hazard. Do not check for leaks with your hand! High-pressure oil streams from breaks in the line could penetrate the skin and cause tissue damage including gangrene. To check for a hose leak, SHUT the unit ENGINE OFF and remove all hydraulic pressure. Wear oil impenetrable gloves, safety glasses and use Cardboard to check for evidence of oil leaks. If you suspect a leak, REMOVE the HOSE and have it tested at a Dealer. If oil does penetrate the skin, have the injury treated immediately by a physician knowledgeable and skilled in this procedure.

Never attempt to lubricate, adjust, or remove material from the Implement while it is in motion or while tractor engine is running.

Periodically inspect all moving parts for wear and replace when necessary with authorized service parts. Look for loose fasteners, worn or broken parts, and leaky or loose fittings. Make sure all pins have cotter pins and washers. Serious injury may occur from not maintaining this machine in good working order.

Do Not fill fuel tank while engine is running. Refuel only after engine has cooled down. If fuel is spilled, move machine away from the area of the spill and avoid creating any source of ignition until the fuel has evaporated. (SBH-49)

Avoid contact with hot surfaces including hydraulic oil tanks, pumps, motors, valves and hose connections. Relieve hydraulic pressure before performing maintenance or repairs. Use gloves and eye protection when servicing hot components. Contact with a hot surface or fluid can cause serious injury from burns or scalding.

1480/1485/1495 01/11

Safety Section 1-14

© 2011 Alamo Group Inc.

Image 18 Contents
1480/1485 1495 To the Owner/Operator/Dealer Table of Contents Maintenance Section Safety Section Safety General Safety Instructions and Practices1480/1485/1495 01/11 Safety Section Operator Safety Instructions and Practices Safety Equipment Operation Safety Instructions and Practices Safety Safety 1480/1485/1495 01/11 Safety Section SL-33 Safety Transporting Safety Instructions and Practices Maintenance and Service Safety Instructions and Practices Safety Storage and Parking Safety Instructions and Practices Concluding Safety Instructions and PracticesDecal Location QTY Level Description Decal Description Safety Safety Safety Safety Federal Laws and Regulations Page Introduction Section Introduction Introductio Introduction Before Operating this Machine Page Assembly and Connecting the Loader Section Assembly Assembly Instructions1480/1485/1495 01/11 Assembly Section Proper Ballasting and Wheel Spacing Dismounting and Mounting Loader Dismounting LoaderAttaching Pin on Bucket Mounting LoaderInstalling Quick-Attach Device Assembling Quick-Attach DeviceWhen Connecting an Attachment to the Loader Quick Hitch Plumbing Hydraulic Valve Attaching Valve Mounting & Valve Attaching Tractor Hydraulic BlockHose Plumbing Plumbing Loader to Control ValvePage Operation Section Operation Rhino 1400 Series LoaderStandard Equipment and Specifications 1480 1485 1495Operator Requirements Operation Tractor Requirements Personal Protective Equipment PPERops and Seat Belt Tractor Lighting and SMV EmblemTractor Ballast Getting On and Off the Tractor Boarding the TractorDismounting the Tractor Starting the Tractor Pre-Operation Inspection and Service Tractor Pre-Operation Inspection/ServiceLoader Pre-Operation Inspection and Service Mount Assembly OPS-L-0007B Do not Operate an Unsafe Tractor or Front END Loader Front END Loader PRE-OPERATION Inspection Driving the Tractor and Loader Operating the Tractor and Loader Driving the Tractor and LoaderSG-36 Operation Operation SL-33 Operation Operating the Loader Filling the BucketOperation Lifting the Load Dumping the Bucket Operating with Float Control Operation Peeling and Scraping Loading LOW Trucks or Spreaders from a Pile Backfilling Operation Handling Large Heavy Objects Operating Bale Spear Loader Storage Transporting the Tractor and ImplementShutting Down the Implement Operation Transporting on Public Roadways Operation Hauling the Tractor and Implement Troubleshooting Guide Trouble Possible Cause Possible RemedyOperation Maintenance Section Maintenance 1480/1485/1495 01/11 Maintenance Section Lubrication Schedule Daily Checks Hydraulic Pressure CheckLift and Bucket Cylinder Disassembly Hydraulic CylinderLift and Bucket Cylinder Reassembly Storage Maintenance Proper Torque for Fasteners Maintenance Maintenance Page Rhino To the OWNER/OPERATOR/DEALER 1480/1485/1495