Servis-Rhino 1598 manual Assembly Instructions

Page 39
(SG-8)
(SL-36)

ASSEMBLY

Assembly Instructions

Never work under the Implement, the framework, or any lifted component unless the Implement is securely supported or blocked up to prevent sudden or inadvertent falling which could cause serious injury or even death.

Never allow anyone to get under the loader or attachment or to reach through the loader lift arms when raised. Serious injury could result from crushing or pinching by the loader or attachment. (SL-06)

Do not modify or alter this Implement. Do not permit anyone to modify or alter this Implement, any of its components or any Implement function.

Never interfere with factory-set hydraulic calibrations. Any change in calibration could cause a failure of the equipment and may result in injury. (SBH-13)

Mounting Kit can be installed using tools ordinarily available, including a hoist capable of lifting and supporting the loader for initial mounting, standard and metric wrenches, torque wrench, and hydraulic oil.

Tractor-supplied hydraulic power is required for loader mounting and operation.

The grille guard (4) may be installed with or without the loader. Refer to Instructions on Page 3-8.

Check tractor tire pressure. Refer to tractor operator’s manual for recommended pressures. With tractor on a firm level surface, compare tractor rear axle height from left to right; measuring from axle center to ground. Adjust air pressure in rear tires until axle height measures same for both sides.

NOTE: If rear axle on tractor is not level from side to side, cutting edge on loader bucket or similar loader- mounted attachments will not sit flat on ground.

Tractor steering stops may have to be adjusted to provide clearance between front tire and loader on full left and right turn with front axle fully oscillated. Be sure lift cylinders are fully retracted when checking tire clearances. Refer to tractor operator’s manual for steering stop adjustment.

NOTE: Reference to left and right used in these instructions refer to position when seated in the operating position on tractor.

1598 01/11

Assembly Section 3-5

© 2011 Alamo Group Inc.

ASSEMBLY

Page 38 Page 40
Image 39
Page 38 Page 40
Contents 1598 To the Owner/Operator/Dealer Table of Contents Maintenance Section Safety Section General Safety Instructions and Practices Safety1598 01/11 Safety Section Operator Safety Instructions and Practices Safety Equipment Operation Safety Instructions and Practices SG-36 Safety Safety SL-33 Safety Safety Transporting Safety Instructions and Practices Maintenance and Service Safety Instructions and Practices Safety Concluding Safety Instructions and Practices Storage and Parking Safety Instructions and PracticesDecal Location QTY Level Description Decal Description D470 Name 1598 01/11 Safety Section Safety Safety Federal Laws and Regulations Page Introduction Section Introduction Introduction Introduction Before Operating this Machine Page Assembly Section General Information AssemblyAssembly Proper Ballasting and Wheel Spacing Assembly Instructions Pallet Component Removal Preparing TractorInstalling Manual Canister to Boom Assembly Installing Left and Right Midmounting BracketsInstalling Grille Guard Plumbing Loader Chart Port IdentificationMounting Loader to Tractor Attaching Bucket to Loader When Connecting an Attachment to the Loader Quick Hitch Connecting Quick Attach Device OptionalPre-Operation Check Dismounting the Loader Mounting Loader Page Operation Section Operation Standard Equipment and Specifications Operator Requirements Operation Personal Protective Equipment PPE Tractor Requirements Rops and Seat BeltTractor Lighting and SMV Emblem Tractor Ballast Getting On and Off the Tractor Boarding the TractorDismounting the Tractor Starting the Tractor Operation Pre-Operation Inspection and Service Loader Pre-Operation Inspection and Service Tractor Pre-Operation Inspection/ServiceMount Assembly Loader Boom Assembly Do not Operate an Unsafe Tractor or Front END Loader Front END Loader PRE-OPERATION Inspection Driving the Tractor and Loader Starting the Tractor Brake and Differential Lock SettingOperating the Tractor and Loader Driving the Tractor and LoaderSG-36 Operation 1598 01/11 Operation Section Operation Filling the Bucket Operating the LoaderOperation Lifting the Load Dumping the Bucket Lowering the Bucket Loading from a Bank Operation Peeling and Scraping Loading LOW Trucks or Spreaders from a Pile Backfilling Operation Handling Large Heavy Objects Operating Bale Spear Valve Lock Loader Storage Transporting the Tractor and Implement Operation Transporting on Public Roadways Hauling the Tractor and Implement Trouble Possible Cause Possible Remedy Troubleshooting GuideMaintenance Section Maintenance 1598 01/11 Maintenance Section Lubrication Schedule Daily Maintenance Storage Maintenance Proper Torque for Fasteners Maintenance Maintenance Page Rhino To the OWNER/OPERATOR/DEALER SOM-01/11 F-4257C Printed U.S.A

1598 specifications

The Servis-Rhino 1598 is a robust and high-performing piece of equipment designed for agricultural and industrial applications. Known for its durability and efficiency, this model has emerged as a vital tool for landowners, farmers, and landscapers alike.

At the heart of the Servis-Rhino 1598 is its impressive cutting ability. The mower features a 15-foot cutting width, enabling users to cover large areas quickly and efficiently. This makes it ideal for cutting grass, weeds, and brush in both pastureland and overgrown areas. The heavy-duty design allows it to handle challenging terrains, making the 1598 a reliable choice in various conditions.

One of the standout features of the Servis-Rhino 1598 is its superior build quality. Constructed with high-strength materials, the mower can withstand heavy use and harsh environmental factors. The cutting deck is reinforced to prevent wear and tear, ensuring longevity and consistent performance over time.

The technology behind the Servis-Rhino 1598 includes an advanced cutting system. Its rotary blade design ensures a clean cut, promoting healthier grass growth. The user can also adjust the cutting height easily, accommodating different types of vegetation and landscape requirements. This flexibility in operation allows users to optimize their mowing tasks effectively.

Another significant feature is the ease of operation. The mower is designed with user comfort in mind, featuring a smooth-rolling transport system that simplifies movement from job to job. The intuitive control layout ensures that operators can maneuver with precision, even in tight spaces.

Additionally, the Servis-Rhino 1598 is equipped with safety features that enhance operational security. These include shielded blades and an emergency stop function, ensuring that the mower operates safely around people and livestock.

Overall, the Servis-Rhino 1598 stands out in the market as a high-quality, efficient, and durable mower, with features and technologies that design it for optimal agricultural and landscaping performance. Whether tackling bushy fields or maintaining expansive lawns, this mower delivers reliable results that meet the needs of modern land management. Its combination of cutting efficiency, durability, and user-friendly operation makes it a must-have for anyone in the agricultural sector.
Top Page Image Contents