McIntosh owner manual How to Operate the C2200, con’t, Default Settings, Output Meters

Page 21

How to Operate the C2200, con’t

Default Settings

To restore the C2200 to Factory Default Settings perform the following. Press and hold in the MONO Push-button together with the OUTPUTS 2 Push-button. Approximately 5 seconds after holding in the two the Front Panel Push-but- tons together, the Front Panel Alphanumeric Display will indicate MASTER RESET. Refer to figure 32.

Figure 32

Release both Push-buttons and the Front Panel Alphanu- meric Display will now indicate -- CLEARED - - and the C2200 will switch Off. Refer to figure 33.

Figure 33

Press the STANDBY/ON Push-button on the C2200 and proceed to the Setup on page 14 to re-enter and custom set- ting that have beeen previously made.

Output Meters

The C2200’s Output Meters indicate the Output Voltage available at the MAIN and OUTPUT 1 & 2 Jacks to drive Power Amplifiers. Refer to figure 34. The Meters are cali- brated in dBs (decibles) and respond to all the peaks con- tained in the musical information. They indicate to an accu- racy of at least 95% of a single cycle from a 2000Hz tone burst.

The Meter Electronic Circuitry “Time Stretches” the Meter Drive Signal so the Meter Pointer pauses just long enough for the human eye to see it and is followed by a moderate decay rate.

Figure 34

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Tube Preamplifier Important Safety Instructions Table of Contents Customer ServiceThank You Please Take a MomentXLR Connectors Connector InformationPower Control and Trigger Connectors Data Port ConnectorPerformance Features Introduction and Performance FeaturesFront View of the C2200 DimensionsRear View of the C2200 Side View of the C2200Enclosed Custom Cabinet InstallationRear Panel Connections How to Connect for Power Control Amplifier Balanced Inputs How to Connect for Audio and Data ControlHow to Connect for Pass Thru Mode How to Connect for a Second Room Meter Lights Front Panel Controls, Displays, Push-Buttons, and SwitchesDefault Settings How to Operate the Setup ModeSetup Function Name Setting Display BrightnessSetup Input Trim LevelRe-Title Inputs Auto Tone Power Control TriggersSetup, con’t Pass Thru Mode Power On OptionRemote Control Selection Input Source Settings Setup, con’t Firmware VersionHow to Operate the C2200 Reset of Microprocessors Pass Thru ModeMono Balance ControlHow to Operate the C2200, con’t Default SettingsOutput Meters Remote Control Push-Buttons How to Operate by Remote Control Volume Control Circuitry Input and Output SwitchingTechnical Description Phono CircuitryOverall Design Specifications Packing Instructions McIntosh Laboratory, Inc Chambers Street Binghamton, NY

C2200 specifications

The McIntosh C2200 is a high-fidelity vacuum tube preamplifier that exemplifies the brand's commitment to craftsmanship, performance, and timeless design. Known for its lush sound quality, the C2200 is a premier choice for audiophiles seeking to enhance their audio experience with the warmth and richness that only tube technology can provide.

At the heart of the C2200 is a sophisticated vacuum tube circuit design, which significantly contributes to its sonorous and immersive audio output. The preamp employs 12AX7A dual triode tubes in its audio signal path, ensuring that music is delivered with exceptional clarity and detail. The incorporation of these tubes results in a pleasing harmonic distortion that many listeners find desirable, making the C2200 an appealing option for those who prefer the analog sound characteristics.

One of the key features of the McIntosh C2200 is its dual-mono configuration. This design allows the left and right audio channels to operate independently, minimizing crosstalk and ensuring a more accurate soundstage. Incorporating technologies such as the McIntosh Autoformer, the C2200 ensures consistent quality across various load impedances, which is pivotal for optimal audio performance.

This preamplifier is equipped with a variety of inputs, including five line-level inputs, a phono input for both moving coil and moving magnet cartridges, and a home theater bypass for integration into a multi-channel audio system. This versatility ensures that the C2200 can accommodate various sources, from turntables to digital players.

The user-friendly interface of the C2200 features a remote control, allowing effortless adjustments to volume and source selection from the comfort of your listening position. The beautiful glass front panel, illuminated by the iconic McIntosh blue meters, adds a stunning visual component, making the preamp not only an audio device but also an elegant piece of décor.

In terms of build quality, the C2200 is constructed with a robust chassis and high-grade components. The power supply is well-regulated, minimizing noise and ensuring that the audio signal remains uncolored. Additionally, the proprietary McIntosh power guard circuit prevents distortion and damage, promising years of reliable service.

Overall, the McIntosh C2200 stands as a remarkable achievement in audio engineering, offering audiophiles a unique blend of vintage tube warmth, modern technology, and unparalleled build quality. Whether used in a dedicated listening room or as part of a more comprehensive audio system, the C2200 delivers an aural experience that satisfies even the most discerning listeners.
Top Page Image Contents