MTD 616 warranty Cutting Deck Removal, Deck Wash System If equipped

Page 23

Deck Wash System™ (If equipped)

Your tractor’s deck may be equipped with a water port on its surface as part of its deck wash system. Use the Deck Wash System™ (sold separately) to rinse grass clippings from the deck’s underside and prevent the buildup of cor- rosive chemicals. Complete the following steps AFTER EACH MOWING:

1.Drive the tractor to a level, clear spot on your lawn, near enough to a water sillcock (spigot) for your garden hose to reach.

IMPORTANT: Make certain the tractor’s discharge chute is directed AWAY from your house, garage, parked cars, etc.

2.Disengage the PTO (Blade Engage), move the shift lever into the neutral position, set the parking brake, and stop the engine.

3.Thread the hose coupler (packaged with your tractor’s Operator’s Manual) onto the end of your garden hose.

4.Attach the hose coupler to the water port on your decks surface. See Figure 6-2.

5.Turn the water on.

6.While sitting in the operator’s position on the tractor, re-start the engine and place the throttle lever in the FAST (rabbit) position.

7.Disengage the parking brake.

8.Move the tractor’s PTO (Blade Engage) into the ON position.

9.Remain in the operator’s position with the cutting deck engaged for a minimum of two minutes, allowing the underside of the cutting deck to thoroughly rinse.

10.Move the tractor’s PTO (Blade Engage) into the OFF position.

11.Turn the ignition key to the STOP position to turn the tractor’s engine off and engage the parking brake.

12.Turn the water off and detach the hose coupler from the water port on your decks surface.

13.Repeat steps 4-11 on the opposite side of the cutting deck.

Cutting Deck Removal

To remove the cutting deck, proceed as follows:

1.Place the PTO (Blade Engage) knob (or lever) in the disengaged (OFF) position and engage the parking brake.

2.Lower the deck by moving the deck lift lever into the bottom notch on the right fender.

3.Remove the hairpin clip that secures the PTO cable to the rear of the cutting deck. See Figure 6-3. Remove the PTO cable and accompanying spring from the cutting deck.

4.Remove the deck belt from around the tractor’s engine pulley (or electric PTO clutch, if so equipped).

Figure 6-2

Hairpin Clip

Spring

PTO Cable

Figure 6-3

Support Pin

Figure 6-4

6

Maintaining

Your Lawn

Tractor

IMPORTANT: Make certain the tractor’s discharge chute is directed AWAY from your house, garage, parked cars, etc.

On models with a 46- inch deck, it may be necessary to remove the belt keepers from around the engine pul- ley, in order to remove the PTO belt.

This Operators Man- ual covers a range of product specifications for various models. Characteristics and features discussed and/or illustrated in this manual may not be applicable to all models. MTD LLC reserves the right to change product speci- fications, designs, and equipment without notice and without incurring obligation.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents OPERATOR’S Manual Table of Contents Slope Gauge Replace gasoline cap and tighten securely Use only an approved gasoline containerGeneral Operation Never allow children or others in or on towed equip- ment This manual and on the machine Slope OperationService Remove the hex bolt and wing nut from the negative cable Setting Up Your Lawn TractorAttaching the Battery Cables Gas and Oil Fill-upAttaching The Steering Wheel Shipping Brace RemovalAttaching The Seat Standard Adjustment SeatQuick Adjustment Seat Knob Adjustment SeatIf so equipped Identifying the Mulch PlugBrake Pedal Operating Your Lawn TractorBrake Pedal Ignition Switch ModuleThrottle Control Lever Choke ControlPTO Blade Engage Lever Systems Indicator Monitor If EquippedSeat Adjustment Lever If Equipped Electric PTO Blade EngageParking Brake Button Safety Interlock SwitchesReverse Caution Mode Deck Lift LeverStarting the Engine Setting the Cutting HeightEngaging the Parking Brake Drive Pedal Stopping the EngineDriving The Tractor Driving On SlopesEngaging the Blades Setting The Cruise ControlUsing the Deck Lift Lever Moving the Tractor ManuallyMulching If Equipped MowingHeadlights Side to Side Adjusting Your Lawn TractorLeveling the Deck Front To RearQuick Adjust Seat If so equipped Parking Brake AdjustmentSeat Adjustment Steering AdjustmentEngine Cleaning the Engine And DeckMaintaining Your Lawn Tractor Kohler Single ShownRepeat steps 4-11 on the opposite side of the cutting deck Cutting Deck RemovalDeck Wash System If equipped Move the tractor’s PTO Blade Engage into the OFF positionTires BatteryFuses Cutting BladesChanging the Lower Deck Belt 46 Decks Changing the Deck BeltChanging the Transmission Drive Belt Belt Cover Inch Deck Mulch Kit Rear Wheel Weight KitFor an extended period Storing your tractor Inch Two-stage Snow ThrowerYour Responsibility Wide Dirty air cleaner Spark plug wires looseClean pre-cleaner, if so equipped Housing06.18.06 Warranty734-1731 Drive Belt Transmission

616 specifications

The MTD 616 is a versatile and powerful ride-on mower that stands out in the landscaping equipment market due to its robust design and innovative technologies. This machine is particularly well-suited for residential and light commercial users, offering an exceptional combination of performance, comfort, and efficiency.

One of the main features of the MTD 616 is its durable build quality. A strong steel frame ensures the mower can withstand demanding conditions, while a wide cutting deck allows for efficient mowing of larger areas. The mower typically features a 42-inch deck, which strikes a perfect balance between cutting width and maneuverability, making it ideal for both open lawns and more confined spaces.

The MTD 616 is powered by a reliable engine, usually a gas-powered unit, providing sufficient torque and power to handle various grass types and terrains. This ensures that users can tackle thick grass and uneven ground without issues. The mower's transmission system is designed for smooth operation, often featuring an automatic or hydrostatic transmission that enables seamless speed adjustments while mowing.

In terms of user comfort, the MTD 616 is equipped with an ergonomic seat and intuitive controls, making it easy for operators to navigate and operate the mower efficiently. The machine's adjustable cutting height allows users to customize their mowing experience, accommodating different grass lengths and varying seasonal growth patterns.

Additionally, the MTD 616 highlights advanced technologies aimed at enhancing functionality. Some models incorporate a mulching feature, which helps in returning cut grass to the lawn as nutrient-rich mulch, promoting healthier growth. Other models may offer bagging options for easy collection of clippings, keeping the lawn tidy.

Safety is an important consideration, and the MTD 616 typically includes features such as a blade brake that stops the mower blades when the operator leaves the seat, ensuring greater safety during operation. Furthermore, its compact design and tight turning radius enhance maneuverability, making it suitable for navigating around landscaping features and garden beds.

Overall, the MTD 616 stands out as a formidable choice for users seeking a reliable and efficient ride-on mower. Its combination of robust construction, advanced features, and user-friendly design positions it as an excellent investment for maintaining a beautiful and well-manicured lawn. Whether it’s for homeowners or light commercial use, the MTD 616 offers the performance and versatility needed for effective grass management.
Top Page Image Contents