MTD 616 warranty Changing the Deck Belt, Changing the Transmission Drive Belt

Page 26

6

Maintaining

Your Lawn

Tractor

WARNING

Be sure to shut the engine off, remove ignition key, discon- nect the spark plug wire(s) and ground against the engine to prevent unintended starting before remov- ing the belt(s).

Avoid the possibility of a pinching injury. Do not place your fingers on the idler spring or between the belt and a pulley while removing the belt.

Changing the Deck Belt

WARNING: Be sure to shut the engine off, remove ignition key, disconnect the spark plug wire(s) and ground against the engine to prevent unintended starting before removing the belt(s).

All belts on your tractor are subject to wear and should be replaced if any signs of wear are present.

IMPORTANT: The V-belts found on your tractor are specially designed to engage and disengage safely. A substitute (non-OEM) V-belt can be dangerous by not disengaging completely. For a proper working machine, use factory approved belts.

To change or replace the deck belt and PTO belt on your tractor, proceed as follows:

1.Remove the belt keeper rod(s) from around the engine pulley.

2.Remove the cutting deck as instructed earlier in this section.

3.Remove the belt guards by removing the self-tapping screws that fasten them to the deck.

4.Carefully loosen, but do not remove, the deck idler pulleys.

5.Remove the deck belt from around all pulleys, including the deck idler pulleys and the electric PTO clutch (units with electric PTO).

6.Route the new belt as shown in Fig. 6-7, 6-8, and 6-9 and retighten the deck idler pulleys.

7.Reinstall the belt guards removed earlier and remount the deck to the tractor.

8.Route the belt around the engine pulley and reinstall the belt keeper rod(s).

Changing the Lower Deck Belt (46” Decks)

NOTE: Several components must be removed in order to change the tractor’s lower deck belt. See an authorized Service Dealer to have your lower drive belt replaced

or phone Customer Support as instructed on page 2 for information on ordering a Service Manual.

Changing the Transmission Drive Belt

NOTE: Several components must be removed and special tools (i.e. air/impact wrench) in order to change the tractor’s drive belt. See an authorized dealer to have your drive belts replaced.

Figure 6-7

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents OPERATOR’S Manual Table of Contents Slope Gauge Use only an approved gasoline container Replace gasoline cap and tighten securelyGeneral Operation This manual and on the machine Slope Operation Never allow children or others in or on towed equip- mentService Gas and Oil Fill-up Setting Up Your Lawn TractorAttaching the Battery Cables Remove the hex bolt and wing nut from the negative cableShipping Brace Removal Attaching The Steering WheelKnob Adjustment Seat Standard Adjustment SeatQuick Adjustment Seat Attaching The SeatIdentifying the Mulch Plug If so equippedOperating Your Lawn Tractor Brake PedalChoke Control Ignition Switch ModuleThrottle Control Lever Brake PedalElectric PTO Blade Engage Systems Indicator Monitor If EquippedSeat Adjustment Lever If Equipped PTO Blade Engage LeverDeck Lift Lever Safety Interlock SwitchesReverse Caution Mode Parking Brake ButtonStarting the Engine Setting the Cutting HeightEngaging the Parking Brake Driving On Slopes Stopping the EngineDriving The Tractor Drive PedalMoving the Tractor Manually Setting The Cruise ControlUsing the Deck Lift Lever Engaging the BladesMulching If Equipped MowingHeadlights Front To Rear Adjusting Your Lawn TractorLeveling the Deck Side to SideSteering Adjustment Parking Brake AdjustmentSeat Adjustment Quick Adjust Seat If so equippedKohler Single Shown Cleaning the Engine And DeckMaintaining Your Lawn Tractor EngineMove the tractor’s PTO Blade Engage into the OFF position Cutting Deck RemovalDeck Wash System If equipped Repeat steps 4-11 on the opposite side of the cutting deckBattery TiresCutting Blades FusesChanging the Lower Deck Belt 46 Decks Changing the Deck BeltChanging the Transmission Drive Belt Belt Cover Inch Two-stage Snow Thrower Rear Wheel Weight KitFor an extended period Storing your tractor Inch Deck Mulch KitYour Responsibility Housing Spark plug wires looseClean pre-cleaner, if so equipped Wide Dirty air cleanerWarranty 06.18.06Drive Belt Transmission 734-1731

616 specifications

The MTD 616 is a versatile and powerful ride-on mower that stands out in the landscaping equipment market due to its robust design and innovative technologies. This machine is particularly well-suited for residential and light commercial users, offering an exceptional combination of performance, comfort, and efficiency.

One of the main features of the MTD 616 is its durable build quality. A strong steel frame ensures the mower can withstand demanding conditions, while a wide cutting deck allows for efficient mowing of larger areas. The mower typically features a 42-inch deck, which strikes a perfect balance between cutting width and maneuverability, making it ideal for both open lawns and more confined spaces.

The MTD 616 is powered by a reliable engine, usually a gas-powered unit, providing sufficient torque and power to handle various grass types and terrains. This ensures that users can tackle thick grass and uneven ground without issues. The mower's transmission system is designed for smooth operation, often featuring an automatic or hydrostatic transmission that enables seamless speed adjustments while mowing.

In terms of user comfort, the MTD 616 is equipped with an ergonomic seat and intuitive controls, making it easy for operators to navigate and operate the mower efficiently. The machine's adjustable cutting height allows users to customize their mowing experience, accommodating different grass lengths and varying seasonal growth patterns.

Additionally, the MTD 616 highlights advanced technologies aimed at enhancing functionality. Some models incorporate a mulching feature, which helps in returning cut grass to the lawn as nutrient-rich mulch, promoting healthier growth. Other models may offer bagging options for easy collection of clippings, keeping the lawn tidy.

Safety is an important consideration, and the MTD 616 typically includes features such as a blade brake that stops the mower blades when the operator leaves the seat, ensuring greater safety during operation. Furthermore, its compact design and tight turning radius enhance maneuverability, making it suitable for navigating around landscaping features and garden beds.

Overall, the MTD 616 stands out as a formidable choice for users seeking a reliable and efficient ride-on mower. Its combination of robust construction, advanced features, and user-friendly design positions it as an excellent investment for maintaining a beautiful and well-manicured lawn. Whether it’s for homeowners or light commercial use, the MTD 616 offers the performance and versatility needed for effective grass management.
Top Page Image Contents